ТОПЛИВНЫЙ НАСОС СНЯТИЕ


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work Click here.

  2. DISCHARGE FUEL SYSTEM PRESSURE

    Click here

  3. REMOVE REAR NO. 2 FLOOR BOARD


    1. Снимите панель заднего пола № 2.

  4. REMOVE REAR DECK FLOOR BOX


    1. Снимите заднюю напольную коробку полки багажного отделения.

  5. REMOVE REAR NO. 3 FLOOR BOARD


    1. Снимите панель заднего пола № 3.

  6. REMOVE DECK FLOOR BOX RH


    1. A003Z5J

      Снимите фиксатор.

    2. Освободите 6 направляющих и снимите правую напольную коробку полки багажного отделения.

  7. REMOVE REAR FLOOR BOARD UPPER NO. 3 PLATE


    1. A003VKN

      Освободите 4 захвата и 2 направляющих, и снимите верхнюю пластину панели заднего пола № 3.

  8. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  9. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. Открепите крепление подушки сиденья от кузова автомобиля, как показано на рисунке.

      Note

      Поскольку каркас подушки легко деформируется, аккуратно соблюдайте приведенные ниже указания.


      1. A003ZN5E01
        Обозначения на рисунке
        *1 Крюк
        *2 Направляющая

        Выберите крепление, которое будет отсоединяться первым. Расположите руки рядом с креплением, как показано на рисунке. Затем поднимите подушку сиденья, чтобы отсоединить крепление.

      2. Повторите описанный выше шаг для другого крепления.

    2. Освободите направляющую подушки сиденья от спинки сиденья.

    3. A003YWG
      Номинальная величина
      *a 100 мм (3,94 дюйма) или менее

      Выверните болт и отсоедините центральный ремень безопасности заднего сиденья в сборе.

    4. Вытяните центральный задний ремень безопасности в сборе из подушки заднего сиденья в сборе.

    5. Снимите подушку заднего сиденья в сборе.

  10. REMOVE REAR SEAT CUSHION LOCK HOOK


    1. A003Y4L

      Освободите захват и снимите крепление подушки заднего сиденья.

      Note

      Крепления подушки заднего сиденья не подлежат повторному использованию.

      Tech Tips

      Порядок выполнения работ для левой и правой сторон одинаков.

  11. REMOVE REAR FLOOR SERVICE HOLE COVER


    1. A003VCS

      Remove the rear floor service hole cover.

    2. A003Y96

      Disconnect the connector from the fuel suction tube with pump and gauge assembly.

  12. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. A003ZALE01
      Text in Illustration
      *1 Tube Joint Clip
      *2 Fuel Tube Joint
      *3 O-ring

      Remove the tube joint clip, then pull the fuel tube joint out of the plug of the fuel suction tube with pump and gauge assembly.

      Note


      • Check that there is no dirt or other foreign matter around the fuel tube joint before disconnecting it. Clean the joint if necessary.

      • It is necessary to prevent dirt or foreign matter from entering the joint. If dirt or foreign matter gets in the joint, the O-rings may not seal properly.

      • Only disconnect the joint by hand.

      • Do not bend, kink or twist the nylon tubes.

      • Protect the contact surfaces by covering it with a plastic bag.

  13. DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY


    1. A003YGZE01

      Loosen the clip and disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel suction tube with pump and gauge assembly.

  14. DISCONNECT NO. 1 CHARCOAL CANISTER OUTLET HOSE


    1. A003VS3

      Disconnect the No. 1 charcoal canister outlet hose from the fuel suction tube with pump and gauge assembly.

  15. DISCONNECT FUEL TANK EVAPORATION TUBE


    1. A003Z5EE01
      Text in Illustration
      *1 Retainer

      Release the retainer and disconnect the fuel tank evaporation tube from the fuel suction tube with pump and gauge assembly.

  16. REMOVE FUEL PUMP GAUGE RETAINER


    1. A003W9BE01
      Text in Illustration
      *1

      SST

      (Plate)
      *2

      SST

      (Claw)
      *3 Rib

      Temporarily install the SST plate and claws to the fuel pump gauge retainer.

      SST
      09808-14030   ( 09808-01030, 09808-01040, 09808-01050 )

      Tech Tips

      Engage the SST claws securely with the fuel pump gauge retainer ribs to secure SST.

    2. While pressing the claws of SST to the fuel pump gauge retainer ribs securely, tighten the bolts.

      Tech Tips

      Install SST while pressing the SST claws toward the fuel pump gauge retainer (towards the center of SST).

    3. Install the SST handle.

    4. A003ZI8E01
      Text in Illustration
      *1

      SST

      (Handle)
      *2

      SST

      (Plate)
      *3

      SST

      (Claw)

      Lightly press down on SST to prevent it from separating from the retainer. While pressing SST, rotate the handle slowly to loosen the retainer.

      SST
      09808-14030   ( 09808-01010, 09808-01020, 09808-01030, 09808-01040, 09808-01050 )

      Note


      • Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.

      • Do not press down on SST excessively as this may make the retainer hard to rotate, and may damage components.

      • Make sure to rotate the SST handle horizontally. If the SST handle is rotated at an angle, SST may come off.

      • Do not spin SST too fast or use an impact wrench as this may result in damage to components.

      • If SST comes off of the retainer, loosen the SST bolts and reinstall SST.

      Tech Tips

      The ribs on the fuel pump gauge retainer can be fitted into the tips of SST.

    5. Remove the fuel pump gauge retainer while holding the fuel suction tube with pump and gauge assembly by hand.

  17. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


    1. A003VYP

      Remove the fuel suction tube with pump and gauge assembly from the fuel tank.

      Note

      Make sure that the fuel sender gauge arm does not bend.

    2. A003WE8E02
      Text in Illustration
      *1 Gasket

      Remove the gasket from the fuel tank.