БЛОК ДВИГАТЕЛЯ СНЯТИЕ


  1. INSTALL ENGINE STAND


    1. Install the engine onto an engine stand with the bolts.

  2. REMOVE ENGINE HANGERS


    1. A003X6R

      Remove the 2 bolts and 2 engine hangers.

  3. REMOVE THROTTLE BODY ASSEMBLY


    1. A003WJA

      Отсоедините разъем корпуса дроссельной заслонки и 2 перепускных шланга охлаждающей жидкости.

    2. Выверните 2 болта, отверните 2 гайки и снимите корпус дроссельной заслонки в сборе.

    3. A003WFN

      Снимите прокладку с впускного коллектора.

  4. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    1. Remove the engine oil level dipstick.

    2. A003ZA1

      Remove the 2 bolts, clamp and engine oil level dipstick guide.

    3. Remove the O-ring from the engine oil level dipstick guide.

  5. REMOVE WATER BY-PASS PIPE


    1. A003YBG

      Disconnect the 2 water hoses.

    2. Remove the 2 bolts, nut and water by-pass pipe.

  6. REMOVE INTAKE MANIFOLD


    1. A003WJV

      Disconnect the 2 wire harness clamps.

    2. A003WQ0

      Remove the bolt and wire harness support.

    3. A003ZUX

      Remove the 2 bolts and surge tank cover.

    4. Remove the gasket from the intake manifold.

    5. A003ZLL

      Disconnect the 3 connectors and 2 wire harness clamps.

    6. Remove the engine oil level dipstick.

    7. A003XWA

      Disconnect the wire harness clamp, and then remove the 2 bolts and engine oil level dipstick guide sub-assembly.

    8. Remove the O-ring from the engine oil level dipstick guide sub-assembly.

    9. A003VBE

      Disconnect the fuel vapor feed hose and ventilation hose.

    10. A003VFZ

      Remove the 2 bolts, 2 nuts and intake manifold.

    11. Remove the No. 1 intake manifold to head gasket.

  7. REMOVE FUEL VAPOR FEED PIPE


    1. A003W3O

      Remove the bolt and fuel vapor feed pipe.

  8. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY


    1. A003WKH

      Remove the bolt.

    2. A003Z7A

      Remove the 2 bolts and fuel delivery pipe sub-assembly.

      Note

      Be careful not to drop the fuel injectors when removing the fuel delivery pipe.

  9. REMOVE NO. 1 DELIVERY PIPE SPACER


    1. A003VR5

      Remove the 2 delivery pipe spacers from the cylinder head.

  10. REMOVE FUEL INJECTOR ASSEMBLY


    1. A003WXD

      Pull the 4 fuel injector assemblies out of the fuel delivery pipe sub-assembly.

    2. Remove the O-ring from each fuel injector assembly.

    3. For reinstallation, attach a tag or label to each injector shaft.

      Note

      Prevent entry of foreign objects by covering the fuel injectors with plastic bags.

    4. A003YPM

      Remove the 4 injector vibration insulators.

  11. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    1. A003XRH

      Remove the 3 bolts and No. 1 exhaust manifold heat insulator.

  12. REMOVE MANIFOLD STAY


    1. A003ZQD

      Remove the 3 bolts and manifold stay.

  13. REMOVE EXHAUST MANIFOLD


    1. A003YA8

      Remove the 5 nuts, exhaust manifold and gasket.

  14. REMOVE VENTILATION HOSE


    1. A003VNR

      Remove the ventilation hose from the ventilation valve.

  15. REMOVE IGNITION COIL ASSEMBLY


    1. A003VYT

      Отсоедините разъемы 4 катушек зажигания.

    2. Выверните 4 болта и снимите 4 катушки зажигания.

      Note

      При снятии катушек зажигания соблюдайте осторожность, чтобы не повредить наконечники свечей зажигания о края отверстия в крышке головки блока цилиндров или верхнюю кромку трубки свечного колодца.