DATA LIST
Tech Tips
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Sliding Roof / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Open Switch | Roof sunshade switch open signal/ON or OFF | ON: Open switch pressed OFF: Open switch not pressed |
- |
| Close Switch | Roof sunshade switch close signal/ON or OFF | ON: Close switch pressed OFF: Close switch not pressed |
- |
| Hall IC1 Status | Roof sunshade operation signal/Normal or Lock | Normal: Sliding roof motor operating Lock: Sliding roof motor not operating |
- |
| Hall IC1 Pulse | Roof sunshade operation signal/Lo or Hi | Lo: Sliding roof motor not operating Hi: Sliding roof motor operating |
- |
| Hall IC2 Status | Roof sunshade operation signal/Normal or Lock | Normal: Sliding roof motor operating Lock: Sliding roof motor not operating |
- |
| Hall IC2 Pulse | Roof sunshade operation signal/Lo or Hi | Lo: Sliding roof motor not operating Hi: Sliding roof motor operating |
- |
| Ignition (Direct Signal) | Ignition switch signal/ON or OFF | ON: Ignition switch ON OFF: Ignition switch off |
- |
| Ignition (MPX) | Ignition switch signal (MPX signal)/ON or OFF | ON: Ignition switch ON OFF: Ignition switch off |
- |
| Open Switch Failure(Past) | Open switch failure signal (Past)/Fail or Not Fail | Fail: Roof sunshade open signal failure (Past) Not Fail: No roof sunshade open signal failure (Past) |
- |
| Close Switch Failure(Past) | Close switch failure signal (Past)/Fail or Not Fail | Fail: Roof sunshade close signal failure (Past) Not Fail: No roof sunshade close signal failure (Past) |
- |
| Open Switch Failure(Current) | Open switch failure signal (Current)/Fail or Not Fail | Fail: Roof sunshade open signal failure (Current) Not Fail: No roof sunshade open signal failure (Current) |
- |
| Close Switch Failure(Current) | Close switch failure signal (Current)/Fail or Not Fail | Fail: Roof sunshade close signal failure (Current) Not Fail: No roof sunshade close signal failure (Current) |
- |
| Number of Trouble Codes | Number of trouble codes/Min.: 0, Max.: 255 | Number of DTCs displayed | - |
ACTIVE TEST
Tech Tips
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Sliding Roof / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Slide Roof | Operate roof sunshade | Clos/Up: Roof sunshade close operation occurs Opn/Dwn: Roof sunshade open operation occurs OFF: Roof sunshade is not operating |
Be careful to avoid injuries as this test causes vehicle parts to move. |