FRONT SEAT OUTER BELT ASSEMBLY DISPOSAL

CAUTION / NOTICE / HINT

Tech Tips

When scrapping vehicles equipped with a seat belt pretensioner or disposing of a front seat outer belt (with seat belt pretensioner), always first activate the seat belt pretensioner in accordance with the procedures described below. If any abnormality occurs during activation of the seat belt pretensioner, contact the service department of the distributor.

CAUTION:


  • Before deploying any SRS components for disposal, carefully review and follow all applicable environmental and hazardous material regulations. Depending on the area, deployment of SRS components before disposal may be considered treatment of hazardous materials, which may require special training, certification or licensing.

  • Never dispose of a front seat outer belt that has an un-activated pretensioner.

  • The seat belt pretensioner produces a loud, exploding sound when it activates. Perform the operation where it will not be a nuisance to nearby people.

  • When activating a front seat outer belt (with seat belt pretensioner), stand at least 10 m (32.8 ft.) away from the front seat outer belt.

  • Use gloves and safety glasses when handling a front seat outer belt with an activated pretensioner.

  • Always wash your hands with water after completing the disposal.

  • Do not apply water to a front seat outer belt that has an activated pretensioner.

  • Perform procedures in a place away from electrical interference.

  • When activating the seat belt pretensioner, always use the specified SST (SRS airbag deployment tool).

PROCEDURE


  1. DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (WHEN INSTALLED IN VEHICLE)

    Tech Tips

    Prepare a battery to activate the seat belt pretensioner.


    1. A005KLCE02

      Check if SST is functioning properly.

      SST
      09082-00700
      09082-00770

      CAUTION:

      When activating the seat belt pretensioner, always use the specified SST.


      1. A005HKEE13
        Text in Illustration
        *1 Battery

        Connect the red clip of SST to the positive (+) battery terminal and the black clip to the negative (-) battery terminal.

        Tech Tips

        Do not connect the yellow connector. The yellow connector is used to connect the seat belt pretensioner.

      2. A005M9CE06

        Press SST activation switch and check that the LED of SST activation switch illuminates.

        CAUTION:

        If the LED illuminates when the activation switch is not being pressed, SST may be malfunctioning. Replace SST with a new one.

    2. Disconnect SST from the battery.

    3. Disconnect the pretensioner connector.

    4. Prepare SST for activation of the seat belt pretensioner.


      1. Install the floor anchor of the seat belt.

      2. A005JYIE06

        Connect SST (A) to SST (B). Then connect the connector of SST (B) to the seat belt pretensioner.

        Note

        To avoid damaging SST connector and wire harness, do not lock the secondary lock of the twin lock.

      3. A005L4FE01
        Text in Illustration
        *a 10 m (32.8 ft.) or more

        Move SST at least 10 m (32.8 ft.) away from the front of the vehicle.

      4. Close all the doors and windows of the vehicle.

        Tech Tips

        Leave a gap in one of the windows for SST wire harness.

        Note

        Take care not to damage SST wire harness.

      5. Connect the red clip of SST to the positive (+) battery terminal and the black clip to the negative (-) battery terminal.

    5. Activate the seat belt pretensioner.


      1. Confirm that no one is inside the vehicle or within 10 m (32.8 ft.) of the vehicle.

      2. Press SST activation switch to activate the seat belt pretensioner.

        Tech Tips

        The seat belt pretensioner operates at the same time SST activation switch LED illuminates.

    6. Dispose of the front seat outer belt (with the seat belt pretensioner).

      CAUTION:


      • Do not touch the front seat outer belt for at least 30 minutes after the seat belt pretensioner has been activated. It is very hot.

      • Use gloves and safety glasses when handling a front seat outer belt whose pretensioner has been activated.

      • Always wash your hands with water after completing the disposal.

      • Do not apply water to a front seat outer belt that has an activated pretensioner.

      Tech Tips

      When scrapping a vehicle, activate the seat belt pretensioner, and then scrap the vehicle with the activated front seat outer belt installed.

  2. DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE)

    Note

    Be sure to follow the procedures listed below when activating the seat belt pretensioner.


    1. A005JSSE03

      Remove the front seat outer belt assembly Click here.

    2. Wind the seat belt with the retractor.

    3. When the seat belt is sufficiently wound, cut the seat belt approximately 100 mm (3.94 in.) from the retractor as shown in the illustration.

      Tech Tips

      The seat belt is designed so that winding the seat belt before pretensioner activation will decrease the pulling power of the seat belt during pretensioner activation.

      Text in Illustration
      *a Cut Here
    4. A005HKEE13
      Text in Illustration
      *1 Battery

      Check if SST is functioning properly.

      SST
      09082-00700
      09082-00770

      CAUTION:

      When activating a seat belt pretensioner, always use the specified SST.

    5. A005JYIE06

      Prepare SST for activation of the seat belt pretensioner.


      1. Connect SST (A) to SST (B). Then connect the connector of SST (B) to the seat belt pretensioner.

        Note

        To avoid damaging SST connector and wire harness, do not lock the secondary lock of the twin lock.

      2. A005KG2E07

        Place the front seat outer belt on the ground and cover it with a tire (with wheel).

        Note

        Set up the front seat outer belt as shown in the illustration.

      3. A005K45E06
        Text in Illustration
        *a 10 m (32.8 ft.) or more

        Move SST at least 10 m (32.8 ft.) away from the wheel.

        Note

        Take care not to damage SST wire harness.

    6. Activate the seat belt pretensioner.


      1. Connect the red clip of SST to the positive (+) battery terminal and the black clip to the negative (-) battery terminal.

      2. Check that no one is within 10 m (32.8 ft.) of the wheel.

      3. Press SST activation switch to activate the seat belt pretensioner.

        Tech Tips

        The seat belt pretensioner operates at the same time SST activation switch LED illuminates.

    7. Dispose of the front seat outer belt (with the seat belt pretensioner).

      CAUTION:


      • Do not touch the front seat outer belt for at least 30 minutes after the seat belt pretensioner has been activated. It is very hot.

      • Use gloves and safety glasses when handling a front seat outer belt whose pretensioner has been activated.

      • Always wash your hands with water after completing the disposal.

      • Do not apply water to a front seat outer belt that has an activated pretensioner.


      1. Remove the tire (with wheel) and SST.

      2. A005KJW

        Place the front seat outer belt in a plastic bag, tie the end tightly and dispose of it in the same way as other general parts.