PROCEDURE
INSPECT SPEEDOMETER
Check the operation.
Note
The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.
The Data List values of the skid control ECU are used for this inspection. Therefore, make sure to perform this inspection after confirming that no DTCs are output from the vehicle stability control system.
If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.
Before starting the following inspection, check if vehicle stability control system DTCs are output Click here.
Warm up the engine.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Vehicle Speed | Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| GTS Indication (km/h) | Acceptable Range (km/h) Data in ( ) is for Reference |
|---|---|
| 20 | (21.0 to 25.0) |
| 40 | 41.7 to 46.2 |
| 60 | 62.7 to 67.2 |
| 80 | 83.4 to 88.4 |
| 100 | 104.3 to 109.3 |
| 120 | 125.1 to 130.6 |
| 140 | 145.8 to 151.8 |
| 160 | 166.2 to 173.2 |
| 180 | 186.9 to 194.5 |
| 200 | 207.7 to 215.7 |
| 220 | 228.4 to 236.8 |
| 240 | 249.2 to 258.0 |
| 260 | 270 to 279.2 |
| GTS Indication (mph) | Acceptable Range (mph) |
|---|---|
| 20 | 21.0 to 23.5 |
| 40 | 42.0 to 44.5 |
| 60 | 62.5 to 66.0 |
| 80 | 83.1 to 87.1 |
| 100 | 103.9 to 108.4 |
| 120 | 124.7 to 129.6 |
| 140 | 145.4 to 150.7 |
| 160 | 166.2 to 171.9 |
| 180 | 187.0 to 193.0 |
Check the deflection width of the speedometer indicator.
| Reference |
|---|
| Within 0.3° |
INSPECT TACHOMETER
Check the operation.
Before starting the following inspection, check if ECD system*1, SFI system*2 DTCs are output.
for 1NR-FE Click here
for 1ND-TV Click here
for 1NZ-FE Click here
Warm up the engine.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 16383 rpm |
600 to 700 rpm: Idling (for CVT) 550 to 650 rpm: Idling (for Manual Transaxle) |
When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 16383 rpm |
720 to 820 rpm: Idling | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 16383 rpm |
680 to 780 rpm: Idling | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed |
| GTS Indication (rpm) | Acceptable Range (rpm) Data in ( ) is for Reference |
|---|---|
| 700 | 630 to 770 |
| 1000 | (900 to 1100) |
| 2000 | (1850 to 2150) |
| 3000 | 2800 to 3200 |
| 4000 | (3800 to 4200) |
| 5000 | 4800 to 5200 |
| 6000 | (5750 to 6250) |
| 7000* | (6700 to 7300) |
| 8000* | (7700 to 8300) |
*1: for 1ND-TV
*2: except 1ND-TV
Check the deflection width of the tachometer indicator.
| Reference |
|---|
| Within 0.3° |
Check LED illumination (LED check)
Check the illumination function of the warning or indicator lights listed below when turning the ignition switch to ON.
| Warning or Indicator Light | Specification |
|---|---|
| BRAKE, ABS, VSC OFF, SLIP, TRC OFF, TEMP HOT, OIL LEVEL*1, OIL MAINTENANCE*1, DPF*1, ECO*2, ECO RUN*3, ECO RUN OFF*3, SEDIMENT*1, TIRE PRESSURE*5 | Warning or indicator light comes on for about 3 seconds after turning the ignition switch to ON. |
| AIRBAG | Warning light comes on for about 6 seconds after turning the ignition switch to ON. |
| OIL PRESSURE, CHECK ENGINE, CHARGE, EPS, SHIFT UP/DOWN*4 | Warning or indicator light comes on after turning the ignition switch to ON and the indicator light goes off after the engine starts. |
*1: for 1ND-TV
*2: w/ ECO Driving Indicator
*3: w/ Stop and Start System
*4: for Manual Transaxle
*5: except 1NZ-FE