ENTRY AND START SYSTEM(for Entry Function) Front Passenger Side Door Entry Lock and Unlock Functions do not Operate

DESCRIPTION

When the front passenger door entry lock and unlock functions do not operate, one of the following may be malfunctioning: 1) power door lock control system; 2) front door outside handle assembly (for front passenger side electrical key antenna); or 3) certification ECU (smart key ECU assembly).

WIRING DIAGRAM

A005LR9E07

CAUTION / NOTICE / HINT

Note


  • The entry and start system (for entry function) uses a multiplex communication system (LIN communication system) and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for entry function) after confirming that the communication system is functioning properly.

  • When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3, and turn a courtesy light switch on and off at 1.5-second intervals until communication between the tester and vehicle begins

  • Check that there are no electrical key transmitters in the vehicle.

  • Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output Click here.

  • When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.

  • Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) Click here.

  • After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".

Tech Tips

If no operations are performed for 14 days with all doors locked, the certification ECU (smart key ECU assembly) stops the entry function for the front passenger side for power save Click here.

PROCEDURE


  1. CHECK POWER DOOR LOCK OPERATION


    1. When the door control switch on the master switch assembly is operated, check that the doors unlock and lock according to switch operation Click here.

      OK
      Door locks operate normally.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM (PROCEED TO PROBLEM SYMPTOMS TABLE) Click here

    OK

  2. CHECK WAVE ENVIRONMENT


    1. A005MK1E01
      Text in Illustration
      *A for LHD
      *B for RHD
      *a Approximately 0.3 m (0.98 ft.)

      Bring the electrical key transmitter near the front door outside handle assembly, and perform a front passenger door entry lock and unlock operation check.

      Note

      If the key is brought within 0.2 m (0.656 ft.) of the door outside handle assembly, communication is not possible.

      Tech Tips


      • When the electrical key transmitter is brought near the front door outside handle assembly, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

      • If the operation is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

      Result
      Result Proceed to
      Entry functions operate abnormally A
      Entry functions operate normally B

    B

    AFFECTED BY WAVE INTERFERENCE

    A

  3. PERFORM KEY DIAGNOSTIC MODE INSPECTION


    1. A005LGWE01
      Text in Illustration
      *A for LHD
      *B for RHD
      *a 0.7 to 1.0 m (2.30 to 3.28 ft.)

      Diagnostic mode inspection (door electrical key antenna (for front passenger side))

      Note

      Perform this check with the vehicle is stopped.


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Passenger Side.

      5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

      Result
      Result Proceed to
      Wireless door lock buzzer does not sound A
      Wireless door lock buzzer sounds B

    B

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    A

  4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)


    1. Disconnect the F63 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the G11*1 or H10*2 front door outside handle assembly connector.

    3. Measure the resistance according to the value(s) in the table below.


      • *1: for LHD

      • *2: for RHD

      Standard Resistance (Check for Open)
      for LHD
      Tester Connection Condition Specified Condition
      F63-11 (CLG2) - G11-6 (ANT1) Always Below 1 Ω
      F63-10 (CG2B) - G11-3 (ANT2) Always Below 1 Ω
      F63-21 (POS2) - G11-5 (B) Always Below 1 Ω
      G11-2 (GND) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      F63-11 (CLG2) - H10-6 (ANT1) Always Below 1 Ω
      F63-10 (CG2B) - H10-3 (ANT2) Always Below 1 Ω
      F63-21 (POS2) - H10-5 (B) Always Below 1 Ω
      H10-2 (GND) - Body ground Always Below 1 Ω
      Standard Resistance (Check for Short)
      for LHD
      Tester Connection Condition Specified Condition
      F63-11 (CLG2) - Body ground Always 10 kΩ or higher
      G11-6 (ANT1) - Body ground Always 10 kΩ or higher
      F63-10 (CG2B) - Body ground Always 10 kΩ or higher
      G11-3 (ANT2) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      F63-11 (CLG2) - Body ground Always 10 kΩ or higher
      H10-6 (ANT1) - Body ground Always 10 kΩ or higher
      F63-10 (CG2B) - Body ground Always 10 kΩ or higher
      H10-3 (ANT2) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (DOOR OUTSIDE HANDLE - BATTERY AND BODY GROUND)


    1. Reconnect the F63 certification ECU (smart key ECU assembly) connector.

    2. A005GRNE01
      Text in Illustration
      *A for LHD
      *B for RHD
      *a

      Front view of wire harness connector

      (to Front Door Outside Handle assembly)

      Measure the pulse generation according to the value(s) in the table below.

      OK
      for LHD
      Tester Connection Condition Specified Condition
      G11-6 (ANT1) - G11-3 (ANT2) Engine switch off, all doors closed, all doors locked with wireless door lock control, and key not in the cabin No pulse generation → Pulse generation
      for RHD
      Tester Connection Condition Specified Condition
      H10-6 (ANT1) - H10-3 (ANT2) Engine switch off, all doors closed, all doors locked with wireless door lock control, and key not in the cabin No pulse generation → Pulse generation

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Switch Condition Specified Condition
      G11-5 (B) - Body ground Engine switch off →Engine switch on (IG) 9 to 12 V → Below 2 V
      for RHD
      Tester Connection Switch Condition Specified Condition
      H10-5 (B) - Body ground Engine switch off →Engine switch on (IG) 9 to 12 V → Below 2 V

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

  6. REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    1. Replace the front door outside handle assembly Click here.


    NEXT

  7. CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    1. Check that the entry functions operate normally Click here.

      OK
      Entry functions operate normally.

    OK

    END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY WAS DEFECTIVE)

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)