ENTRY AND START SYSTEM(for Entry Function), Diagnostic DTC:B27A8

DTC Code DTC Name
B27A8 Open in Outside Luggage Compartment Electrical Key Antenna Circuit

DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the electrical key antenna (outside luggage). For the electrical key antenna (outside luggage) to detect when the key is brought close to the vehicle, the received request signal is transmitted within approximately 1.0 m (3.28 ft.) of the back door. DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (between terminals CLG8 and CLG5, or terminals CG8B and CLGB).

DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B27A8 An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (CLG8 - CLG5, CG8B - CLGB) (1 trip detection logic*1).

  • Wire harness or connector

  • Electrical key antenna (outside luggage)

  • Certification ECU (smart key ECU assembly)

 Any time*2

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for back door -
Related Data List and Active Test
DTC No. Data List and Active Test
B27A8 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

A005IF0E06

CAUTION / NOTICE / HINT

Note


  • The entry and start system (for entry function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for entry function) after confirming that the communication systems are functioning properly.

  • When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

  • Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for entry function) Click here.

  • After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".

  • Electrical key antenna (outside luggage) has an antenna coil between CLG5 and CLGB terminals.

PROCEDURE


  1. CHECK CONNECTOR CONNECTION CONDITION


    1. Turn the engine switch off.

    2. Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and the electrical key antenna (outside luggage).

      OK
      Connectors are properly connected.

    NG

    CONNECT CONNECTORS PROPERLY

    OK

  2. CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)


    1. Disconnect the F64 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the K13 electrical key antenna (outside luggage) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      F64-2 (CLG8) - K13-1 (CLG5) Always Below 1 Ω
      F64-1 (CG8B) - K13-2 (CLGB) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      F64-2 (CLG8) - Body ground Always 10 kΩ or higher
      K13-1 (CLG5) - Body ground Always 10 kΩ or higher
      F64-1 (CG8B) - Body ground Always 10 kΩ or higher
      K13-2 (CLGB) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT ELECTRICAL KEY ANTENNA (Outside Luggage)


    1. A005K1LE09
      Text in Illustration
      *a

      Component without harness connected

      (Electrical Key Antenna (outside luggage))

      Remove the electrical key antenna (outside luggage) Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (CLG5) - 2 (CLGB) Always Below 1 Ω

    NG

    REPLACE ELECTRICAL KEY ANTENNA (Outside Luggage) Click here

    OK

  4. REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


    1. Temporarily replace the certification ECU (smart key ECU assembly) with a new or normally functioning one.


    NEXT

  5. CHECK DTC OUTPUT


    1. Clear the DTCs Click here.

    2. Recheck for DTCs Click here.

      OK
      B27A8 output does not recur.

    OK

    END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

    NG

    REPLACE ELECTRICAL KEY ANTENNA (Outside Luggage) Click here