ENTRY AND START SYSTEM(for Entry Function) CUSTOMIZE PARAMETERS

PROCEDURE


  1. CUSTOMIZE ENTRY AND START SYSTEM (for Entry Function)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Utility / Customize / Entry & Start or Warning.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Park Wait Time (Waiting time to permit unlocking door after locking) 2.5s Function that sets the period of time (lock confirmation time) that the door is prevented from being unlocked by operating the front door outside handle assembly after an entry lock operation is performed. 0.5s, 1.5s, 2.5s or 5s Certification ECU (smart key ECU assembly)

        Ignition Available Area

        (Entry ignition available area)

        		 All Function that sets the area that the key must be in before the engine switch can be operated. Front or All Certification ECU (smart key ECU assembly)
        Back Door Opening Operation Long Function to open the back door when the driver has the electrical key and presses back door opener switch assembly (opener switch). Long, Twice or OFF Certification ECU (smart key ECU assembly)
        Key Low Battery Warning (Warn when key battery becomes weak) ON Enables or disables the sounding of the buzzer when the key battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more. ON or OFF Certification ECU (smart key ECU assembly)
        Auto Entry Cancel SW OFF Function that enables or disables the entry and start system. ON or OFF Certification ECU (smart key ECU assembly)
        Engine Start Indicator ON Function to Turn ON / OFF of the Engine Start Indicator. ON or OFF Certification ECU (smart key ECU assembly)
        Touch Activation Over Threshold* Active The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed. Active or Not Active Certification ECU (smart key ECU assembly)

        • *: for 1NZ-FE

    2. Customizing with the radio receiver assembly (for Radio and Display Type)


      1. Turn the engine switch on (IG).

      2. Select the following menus: SETUP / Vehicle / Entry and Start System.

        Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Entry and Start System On Function that enables or disables the entry and start system. On or Off Certification ECU (smart key ECU assembly)

    3. Entry cancel function

      Tech Tips

      While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the key against the engine switch.


      1. The following functions are disabled when the entry and start system is canceled.


        1. Entry unlock/lock functions

        2. Entry ignition function

        3. Key lock-in prevention function

        4. Entry back door open/lock function

        5. Entry warning functions

      2. Canceling the system operation:


        1. Make sure the following conditions are met:


          • The engine switch is off.

          • The driver side door is closed.

          • The driver side door is unlocked.

        2. Press the unlock switch of the electrical key transmitter.

        3. Open the driver side door within 5 seconds of completing the step above (driver side door: closed at beginning of step → opened).

        4. With the driver side door open, press the unlock switch of the electrical key transmitter 2 times within 5 seconds of completing the step above.

          Note

          If the driver side door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

        5. Close and open the driver side door twice within 30 seconds of completing the above step (driver side door: open at beginning of step → closed → opened → closed → opened).

        6. With the driver side door open, press the unlock switch of the electrical key transmitter 2 times within 30 seconds of completing the step above.

          Note

          If the driver side door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

        7. Close and open the driver side door within 30 seconds of completing the step above (driver side door: open at beginning of step → closed → opened).

        8. Close the driver side door within 5 seconds of completing the above step.

        9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the entry and start system has been canceled.

      3. Perform the following procedure to restore the entry and start system to the active state from the canceled state.


        1. Perform the procedures to cancel the entry and start system again.

        2. Check that the wireless buzzer sounds once (short beep) to confirm that the entry and start system has been restored to the active state.

          Tech Tips


          • The system changes between the canceled state and the active state each time the procedure to cancel the system is performed.

          • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.