ENTRY AND START SYSTEM(for Start Function), Diagnostic DTC:B2284

DTC Code DTC Name
B2284 Brake Signal Malfunction

DESCRIPTION

The certification ECU (smart key ECU assembly) receives brake signal information from 2 sources. It receives a signal from the stop light switch assembly via a direct line, and a signal from the ECM via CAN. If the information from these 2 sources is inconsistent, this DTC will be stored.

Tech Tips

When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.

DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2284 The brake signal information from the direct line and the brake signal information from the ECM via CAN communication are inconsistent (1-trip detection logic*).

  • AM2 fuse

  • MAIN fuse

  • STOP fuse

  • ALT fuse

  • Certification ECU (smart key ECU assembly)

  • SFI system (except 1ND-TV)

  • ECD system (for 1ND-TV)

  • Wire harness or connector

 Connect the cable to the negative (-) battery terminal, turn the brakes off for 20 seconds or more and then turn them on for 20 seconds or more.

*: Only output while a malfunction is present and the engine switch is on (IG)

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected

When the key is inside the vehicle, the engine does not start even though an engine start operation is performed (the entry key indicator in the combination meter assembly does not illuminates in green). However, if the engine switch is pressed and held for a certain period of time after the power source mode is changed to on (ACC), the engine can be started.


  • When a direct line ON malfunction is present, the engine can be started by pressing the engine switch even if the brakes are off.

  • When a direct line OFF malfunction is present, the engine cannot be started by pressing the engine switch even if the brakes are on.

 -

WIRING DIAGRAM

A005MGZE03

CAUTION / NOTICE / HINT

Note


  • When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "MANUAL" from the initial screen on the intelligent tester, and then select "KEY REGIST" under Model Code.

  • The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting Click here.

  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

Tech Tips

Related Data List and Active Test Items

DTC No. Data List Item Active Test Item
B2284

Power Source Control


  • Stop Light Switch1

Powertrain / Engine and ECT


  • ST1

 -

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Power Source Control / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Power Source Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Stop Light Switch1 State of brake pedal / ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      • Use this item to determine whether the stop light switch is malfunctioning.

      • The engine cannot be started when this item is "OFF".

      • When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.
      OK
      ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen.
      Result
      Result Proceed to
      NG A
      OK (for 1NZ-FE) B
      OK (for 1NR-FE) C
      OK (for 1ND-TV) D

    B

    GO TO SFI SYSTEM Click here

    C

    GO TO SFI SYSTEM Click here

    D

    GO TO ECD SYSTEM Click here

    A

  2. CHECK HARNESS AND CONNECTOR (POWER SOURCE)

    A005GV2E01
    Text in Illustration
    *a

    Rear view of harness connected

    (to Certification ECU (Smart Key ECU Assembly))

    1. Disconnect the F65 certification ECU (smart key ECU assembly) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      F65-2 (+B) - Body ground Always 9.5 to 16 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

    OK

  3. CHECK HARNESS AND CONNECTOR (GROUND)


    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F65-11 (E) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (ECU - STOP LIGHT SWITCH ASSEMBLY)


    1. Disconnect the F65 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the A37*1 or A38*2 stop light switch assembly connector.


      • *1: for LED Type Stop Light

      • *2: for Bulb Type Stop Light

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      for LED Type Stop Light
      Tester Connection Condition Specified Condition
      F65-18 (STP1) - A37-1 Always Below 1 Ω
      for Bulb Type Stop Light
      Tester Connection Condition Specified Condition
      F65-18 (STP1) - A38-1 Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      F65-18 (STP1) - Body ground Always 10 kΩ or higher

    4. Reconnect the A37*1 or A38*2 stop light switch assembly connector.


      • *1: for LED Type Stop Light

      • *2: for Bulb Type Stop Light

    5. A005I54E01
      Text in Illustration
      *a

      Component without wire harness connected

      (to Certification ECU (Smart Key ECU Assembly))

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Brake Pedal Operation Specified Condition
      F65-18 (STP1) - Body ground Released Below 1 V
      Depressed 9 V or higher

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR