ENTRY AND START SYSTEM(for Entry Function) OPERATION CHECK


  1. CHECK ENTRY AND START SYSTEM (for Entry Function) OPERATION

    Note

    Make sure that the entry and start system (for entry function) has not been canceled before performing this inspection.


    1. Check the entry unlock function (driver side door, front passenger side door).


      1. Perform a wireless lock operation to lock all the doors, touch the unlock sensor built into the backside of the front door outside handle assembly of the driver side door while carrying the electrical key transmitter and check that all the doors unlock.

        Tech Tips

        To perform a wireless lock operation, press the lock switch of the electrical key transmitter while standing near the front door outside handle assembly.

      2. A005JNUE01
        Text in Illustration
        *a 0.7 to 1 m (2.30 to 3.28 ft.)

        Inspect the entry unlock detection area. Hold the electrical key transmitter at the same height as the front door outside handle assembly (approximately 0.8 m (2.62 ft.) from the ground) and approximately 0.7 m (2.30 ft.) from the vehicle as shown in the illustration and check that the LED (red) of the electrical key transmitter blinks.

        Tech Tips

        The outside mirror illumination turns on.

      3. With the system in unlock standby mode, hold the front door outside handle assembly and check that all the doors unlock.

        Tech Tips


        • The system is in unlock standby mode when the electrical key transmitter is in the detection area and the key ID code sent by the key matches the key ID code stored by the certification ECU (smart key ECU assembly).

        • Communication may not be possible if the electrical key transmitter is within 0.2 m (0.66 ft.) of the front door outside handle assembly.

        • Inspect the front passenger side door using the same procedure.

      4. A005KWCE01
        Text in Illustration
        *1 Unlock Sensor (Backside)

        Check the unlock response sensitivity. With the system in unlock standby mode, touch the area shown in the illustration and check that the door unlocks.

        Note

        If the sensor is touched too quickly or released too slowly, the sensor may not react and the door will not unlock.

    2. Check the entry lock function (driver side door, front passenger side door).

      Note

      If the electrical key transmitter is in the vehicle but outside the detection area (on the instrument panel, in the glove box, on the floor) and a door lock operation is performed, the key lock-in prevention function will not operate and the electrical key transmitter will be locked inside the vehicle.


      1. A005KALE01
        Text in Illustration
        *a Approximately 0.3 m (0.98 ft.)

        With all the doors closed and unlocked, touch the lock sensor of the front door outside handle assembly of the driver side door while carrying the electrical key transmitter and check that all the doors lock.

      2. A005H6ZE01
        Text in Illustration
        *1 Lock Sensor

        Inspect the entry lock operating range. Hold the electrical key transmitter approximately 0.1 m (0.33 ft.) below the bottom edge of the door glass (approximately 0.8 m (2.62 ft.) from the ground) and approximately 0.3 m (0.98 ft.) from the vehicle as shown in the illustration, touch the lock sensor and check that all the doors lock.

        Tech Tips


        • If the door does not lock when you touch the lock sensor, touch the lock sensor with your palm.

        • As communication may not be possible if the electrical key transmitter is within 0.2 m (0.66 ft.) of the front door outside handle assembly, the door may not lock if the lock sensor is touched with the same hand that is holding the electrical key transmitter, etc.

        • If the key lock-in prevention function buzzer sounds, electric waves from the indoor electrical key antenna may be leaking from the vehicle.

        • Inspect the front passenger side door using the same procedure.

    3. Check the entry back door unlock function.


      1. A005KTUE01
        Text in Illustration
        *a Vehicle center
        *b Approximately 0.7 m (2.30 ft.)

        Perform a wireless lock operation to lock all the doors, operate the back door opener switch while carrying the electrical key transmitter and check that all the doors unlock.

      2. Inspect the entry back door unlock operating range. While standing at the rear of the vehicle, hold the electrical key transmitter so that it is facing the direction shown in the illustration at the same height as the back door opener switch assembly and approximately 0.7 m (2.30 ft.) from the vehicle, press the back door opener switch assembly and check that all the doors unlock.

    4. Check the entry back door lock function.

      Note

      If the electrical key transmitter is inside the vehicle and a door lock operation is performed, it is possible that the electrical key transmitter may be locked inside the vehicle.


      1. With all the doors closed and unlocked, press the lock switch of the back door opener switch while carrying the electrical key transmitter outside of the vehicle and check that all the doors lock.

      2. A005H9TE01
        Text in Illustration
        *a Vehicle center
        *b Approximately 0.3 m (0.98 ft.)

        Inspect the entry back door lock operating range. Hold the electrical key transmitter so that it is facing the direction shown in the illustration at the same height as the top edge of the rear bumper and approximately 0.3 m (0.98 ft.) from the vehicle, press the lock of the back door opener switch and check that all the doors lock.

        Tech Tips


        • Communication may not be possible if the electrical key transmitter is within 0.2 m (0.66 ft.) of the rear bumper.

        • If the key lock-in prevention function buzzer sounds, electric waves from the indoor electrical key antenna assembly may be leaking from the vehicle.

    5. Check the entry ignition function (for CVT).


      1. With the engine switch off, move the shift lever to P, depress the brake pedal while carrying the electrical key transmitter and check that the entry key indicator light in the combination meter assembly illuminates green. Then, with the entry key indicator light in the combination meter assembly illuminates green, press the engine switch and check that the engine starts.

      2. With the brake pedal released and the engine switch off, press the engine switch while carrying the electrical key transmitter and check that the power source mode changes as follows: off → on (ACC) → on (IG) → off. However, if the shift lever is in any position other than P while the engine switch is on (IG), the power source mode will not change to off, but to on (ACC).

      3. Stop the vehicle, press the engine switch and check that the power source mode changes to off (the engine stops and all electrical systems are off). However, if the shift lever is in any position other than P, even if the engine switch is pressed while the vehicle is stationary, the power source mode will not change to off, but to on (ACC). Move the shift lever to P, open the door and check that the steering lock operates.

      4. A005HY8E01
        Text in Illustration
        *a Inspection Point

        Inspect the entry ignition operating range (front floor). Place the electrical key transmitter on the front seat at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.

        Note


        • Even if the electrical key transmitter is within the vehicle interior detection area, the electrical key transmitter may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

        • Communication may not be possible if the electrical key transmitter is within 0.2 m (0.66 ft.) of the shift lever.

        • The engine control system cannot be started when the electrical key transmitter is on the instrument panel or in the glove box.

        Tech Tips

        Perform the inspection for both inspection points.

      5. A005I67E01
        Text in Illustration
        *a Inspection Point

        Inspect the entry ignition operating range (inside luggage). Place the electrical key transmitter at either inspection point and check that the engine can be started.

        Note


        • Even if the electrical key transmitter is within the vehicle interior detection area, the electrical key transmitter may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

        • Communication may not be possible if the electrical key transmitter is within 0.2 m (0.66 ft.) of the center of the luggage compartment.

        Tech Tips

        Perform the inspection for both inspection points.

    6. Check the entry ignition function (for Multi-mode Manual Transaxle).


      1. With the engine switch off, move the shift lever to N, depress the brake pedal while carrying the electrical key transmitter and check that the entry key indicator light in the combination meter assembly illuminates green. Then, with the entry key indicator light in the combination meter assembly illuminates green, press the engine switch and check that the engine starts.

      2. With the brake pedal released and the engine switch off, press the engine switch while carrying the electrical key transmitter and check that the power source mode changes as follows: off → on (ACC) → on (IG) → off.

      3. Stop the vehicle, press the engine switch and check that the power source mode changes to off (the engine stops and all electrical systems are off). Open the door and check that the steering lock operates.

      4. A005HY8E01
        Text in Illustration
        *a Inspection Point

        Inspect the entry ignition operating range (front floor). Place the electrical key transmitter on the front seat at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.

        Note


        • Even if the electrical key transmitter is within the vehicle interior detection area, the electrical key transmitter may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

        • Communication may not be possible if the electrical key transmitter is within 0.2 m (0.66 ft.) of the shift lever.

        • The engine control system cannot be started when the electrical key transmitter is on the instrument panel or in the glove box.

        Tech Tips

        Perform the inspection for both inspection points.

        Note

        The engine control system cannot be started when the electrical key transmitter is on the instrument panel or in the glove box.

      5. A005I67E01
        Text in Illustration
        *a Inspection Point

        Inspect the entry ignition operating range (inside luggage). Place the electrical key transmitter at either inspection point and check that the engine can be started.

        Note


        • Even if the electrical key transmitter is within the vehicle interior detection area, the electrical key transmitter may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

        • Communication may not be possible if the electrical key transmitter is within 0.2 m (0.66 ft.) of the center of the luggage compartment.

        Tech Tips

        Perform the inspection for both inspection points.

    7. Check the entry ignition function (for Manual Transaxle).


      1. With the engine switch off, depress the clutch pedal while carrying the electrical key transmitter and check that the entry key indicator light in the combination meter assembly illuminates green. Then, with the entry key indicator light in the combination meter assembly illuminates green, press the engine switch and check that the engine starts.

      2. With the clutch pedal released and the engine switch off, press the engine switch while carrying the electrical key transmitter and check that the power source mode changes as follows: off → on (ACC) → on (IG) → off.

      3. Stop the vehicle, press the engine switch and check that the power source mode changes to off (the engine stops and all electrical systems are off). Open the door and check that the steering lock operates.

      4. A005HY8E01
        Text in Illustration
        *a Inspection Point

        Inspect the entry ignition operating range (front floor). Place the electrical key transmitter on the front seat at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.

        Note


        • Even if the electrical key transmitter is within the vehicle interior detection area, the electrical key transmitter may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

        • Communication may not be possible if the electrical key transmitter is within 0.2 m (0.66 ft.) of the shift lever.

        • The engine control system cannot be started when the electrical key transmitter is on the instrument panel or in the glove box.

        Tech Tips

        Perform the inspection for both inspection points.

        Note

        The engine control system cannot be started when the electrical key transmitter is on the instrument panel or in the glove box.

      5. A005I67E01
        Text in Illustration
        *a Inspection Point

        Inspect the entry ignition operating range (inside luggage). Place the electrical key transmitter at either inspection point and check that the engine can be started.

        Note


        • Even if the electrical key transmitter is within the vehicle interior detection area, the electrical key transmitter may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

        • Communication may not be possible if the electrical key transmitter is within 0.2 m (0.66 ft.) of the center of the luggage compartment.

        Tech Tips

        Perform the inspection for both inspection points.

    8. Check the key lock-in prevention function (vehicle interior).

      Note

      In order to prevent the key lock-in, perform this inspection with the window of a door open.


      1. Turn the engine switch off.

      2. Place the electrical key transmitter on a front or rear seat.

      3. Close all the doors, but make sure all the doors are unlocked.

      4. Touch a front door lock sensor and check that the doors do not lock and the key lock-in prevention function buzzer (external) sounds for approximately 10 seconds.

    9. Check the entry cancel function.


      1. Cancel the entry and start system and check that all the functions of the entry and start system (for entry function) no longer operate.

        Tech Tips


        • Refer to the following procedures to cancel the entry and start system (for entry function) Click here.

        • While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter against the engine switch.

      2. While the key cancel function (entry cancel function) is on, check that all functions of the entry and start system cannot be operated.

    10. Check the answer-back function (hazard warning light flashing and buzzer sounding).

      Entry Operation Wireless Buzzer* Hazard Warning Light
      Entry Door Lock Sounds once Flashes once
      Entry Door Unlock Sounds twice Flashes twice
      Entry Back Door Lock Sounds once Flashes once
      Entry Back Door Unlock Sounds twice Flashes twice

      • *: w/ Wireless Buzzer Answer-back

  2. KEY DIAGNOSTIC MODE (Using Intelligent Tester)

    Note

    Perform this check with the vehicle is stopped.

    Tech Tips

    With key diagnostic mode, it is possible to check if the electrical key transmitter is operating properly with the selected electrical key antenna and within the selected detection area by the sounding of the wireless buzzer.


    1. Enter the following menus: Body / Entry & Start / Utility / Key Communication Check.

    2. Select a part to inspect from the following table.

      Tester Display Inspection Range
      Overhead + Driver Side*1 Front door outside handle assembly (driver side electrical key antenna)
      Overhead + Passenger Side*2 Front door outside handle assembly (front passenger side electrical key antenna)
      Overhead + Front Room*3 No. 1 indoor electrical key antenna assembly (front floor)
      Overhead + Back Door (inside)*4 No. 2 indoor electrical key antenna (inside luggage)
      Overhead + Back Door*5 Electrical key antenna (outside luggage)

    3. Bring the electrical key transmitter near the selected electrical key antenna and check that the wireless door lock buzzer sounds.


      1. A005K1XE01
        Text in Illustration
        *A for LHD
        *B for RHD
        *a Approximately 0.7 m (2.30 ft.)

        *1: Front door outside handle assembly (driver side electrical key antenna)

        Tech Tips


        • Hold the electrical key transmitter at the same height as the front door outside handle assembly (approximately 0.8 m (2.62 ft.) from the ground) in the position shown in the illustration.

        • *2: Perform the same inspection for the front passenger side.

    4. A005HY8E01
      Text in Illustration
      *a Inspection Point

      *3: No. 1 indoor electrical key antenna assembly (front floor)

      Tech Tips

      Place the electrical key transmitter on the front seat cushion of the driver seat or front passenger seat.

    5. A005I67E01
      Text in Illustration
      *a Inspection Point

      *4: No. 2 indoor electrical key antenna (inside luggage)

      Tech Tips

      Place the electrical key transmitter in the luggage compartment. Even if the electrical key transmitter is in the luggage compartment, the buzzer may not sound.

    6. A005KTUE01
      Text in Illustration
      *a Vehicle center
      *b Approximately 0.7 m (2.30 ft.)

      *5: Electrical key antenna (outside luggage)

      Tech Tips

      While standing at the rear of the vehicle, hold the electrical key transmitter in the position shown in the illustration at the same height as the top edge of the rear bumper.