CAN COMMUNICATION SYSTEM TERMINALS OF ECU

Tech Tips

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note


      • Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. JUNCTION CONNECTOR


    1. NO. 1 JUNCTION CONNECTOR (for RHD)

      A005IB0E02
      Text in Illustration
      *a for ECM (Power Train Bus)*1 *b for ECM (V1 Bus)
      *c for Skid Control ECU (Brake Actuator Assembly) (V1 Bus) *d for Main Body ECU (Multiplex Network Body ECU) (V1 Bus)
      *e for Certification ECU (Smart Key ECU Assembly) (V1 Bus)*2 *f for No. 2 Junction Connector (V1 Bus)
      *g for Power Management Control ECU (Power Train Bus)*1 - -
      Terminal No. (Symbol) Wiring Color Connect to
      A61-3 (CANH) B ECM (Power Train Bus)*1
      A61-14 (CANL) W
      A61-9 (CANH) L ECM (V1 Bus)
      A61-20 (CANL) W
      A61-10 (CANH) G Skid Control ECU (Brake Actuator Assembly) (V1 Bus)
      A61-21 (CANL) W
      F82-1 (CANH) R Main Body ECU (Multiplex Network Body ECU) (V1 Bus)
      F82-12 (CANL) W
      F82-3 (CANH) L Certification ECU (Smart Key ECU Assembly) (V1 Bus)*2
      F82-14 (CANL) W
      F82-4 (CANH) SB No. 2 Junction Connector (V1 Bus)
      F82-15 (CANL) W
      F82-10 (CANH) Y Power Management Control ECU (Power Train Bus)*1
      F82-21 (CANL) W

      • *1 : w/ Rear Fog Light

      • *2 : w/ Entry and Start System

    2. NO. 1 JUNCTION CONNECTOR (for LHD)

      A005KZCE02
      Text in Illustration
      *a for TCM (Power Train Bus)*3 *b for ECM (Power Train Bus)
      *c for ECM (V1 Bus) *d for Skid Control ECU (Brake Actuator Assembly) (V1 Bus)
      *e for Main Body ECU (Multiplex Network Body ECU) (V1 Bus) *f for Power Steering ECU Assembly (V1 Bus)
      *g for DLC3 (V1 Bus) *h for No. 2 Junction Connector (V1 Bus)
      *i for Engine Stop and Start ECU (V1 Bus)*4 *j for Power Management Control ECU (Power Train Bus)*5
      Terminal No. (Symbol) Wiring Color Connect to
      A61-1 (CANH) BR TCM (Power Train Bus)*3
      A61-12 (CANL) W
      A61-3 (CANH) B ECM (Power Train Bus)
      A61-14 (CANL) W
      A61-9 (CANH) L ECM (V1 Bus)
      A61-20 (CANL) W
      A61-10 (CANH) G Skid Control ECU (Brake Actuator Assembly) (V1 Bus)
      A61-21 (CANL) W
      F82-1 (CANH) R Main Body ECU (Multiplex Network Body ECU) (V1 Bus)
      F82-12 (CANL) W
      F82-2 (CANH) LG Power Steering ECU Assembly (V1 Bus)
      F82-13 (CANL) W
      F82-3 (CANH) GR DLC3 (V1 Bus)
      F82-14 (CANL) W
      F82-4 (CANH) SB No. 2 Junction Connector (V1 Bus)
      F82-15 (CANL) W
      F82-5 (CANH) BE Engine Stop and Start ECU (V1 Bus)*4
      F82-16 (CANL) W
      F82-10 (CANH) Y Power Management Control ECU (Power Train Bus)*5
      F82-21 (CANL) W

      • *3 : w/ Multi-mode Manual Transaxle System

      • *4 : w/ Stop and Start System

      • *5 : w/o Stop and Start System

    3. NO. 2 JUNCTION CONNECTOR (for RHD)

      A005HMYE02
      Text in Illustration
      *a for Steering Angle Sensor (Spiral Cable Sub-assembly) (V1 Bus)*6 *b for Airbag Sensor Assembly (V1 Bus)
      *c for Radio Receiver Assembly (V1 Bus)*7 *d for Power Steering ECU Assembly (V1 Bus)
      *e for Combination Meter Assembly (V1 Bus) *f for Air Conditioning Amplifier Assembly (V1 Bus)*8
      *g for No. 1 Junction Connector (V1 Bus) *h for DLC3 (V1 Bus)
      Terminal No. (Symbol) Wiring Color Connect to
      F83-1 (CANH) P Steering Angle Sensor (Spiral Cable Sub-assembly) (V1 Bus)*6
      F83-12 (CANL) W
      F83-4 (CANH) B Airbag Sensor Assembly (V1 Bus)
      F83-15 (CANL) W
      F83-5 (CANH) BE Radio Receiver Assembly (V1 Bus)*7
      F83-16 (CANL) W
      F83-6 (CANH) LG Power Steering ECU Assembly (V1 Bus)
      F83-17 (CANL) W
      F83-7 (CANH) G Combination Meter Assembly (V1 Bus)
      F83-18 (CANL) W
      F83-8 (CANH) V Air Conditioning Amplifier Assembly (V1 Bus)*8
      F83-19 (CANL) W
      F83-10 (CANH) SB No. 1 Junction Connector (V1 Bus)
      F83-21 (CANL) W
      F83-11 (CANH) GR DLC3 (V1 Bus)
      F83-22 (CANL) W

      • *6 : w/ VSC

      • *7 : w/ Radio and Display System

      • *8 : w/ Air Conditioning System or Electrical Type Power Heater System

    4. NO. 2 JUNCTION CONNECTOR (for LHD)

      A005GPWE02
      Text in Illustration
      *a for Steering Angle Sensor (Spiral Cable Sub-assembly) (V1 Bus)*6 *b for Certification ECU (smart key ECU assembly) (V1 Bus)*2
      *c for Airbag Sensor Assembly (V1 Bus) *d for Radio Receiver Assembly (V1 Bus)*7
      *e for Combination Meter Assembly (V1 Bus) *f for Air Conditioning Amplifier Assembly (V1 Bus)*8
      *g for No. 1 Junction Connector (V1 Bus) - -
      Terminal No. (Symbol) Wiring Color Connect to
      F83-1 (CANH) P Steering Angle Sensor (Spiral Cable Sub-assembly) (V1 Bus)*6
      F83-12 (CANL) W
      F83-3 (CANH) L Certification ECU (smart key ECU assembly) (V1 Bus)*2
      F83-14 (CANL) W
      F83-4 (CANH) B Airbag Sensor Assembly (V1 Bus)
      F83-15 (CANL) W
      F83-5 (CANH) BE Radio Receiver Assembly (V1 Bus)*7
      F83-16 (CANL) W
      F83-7 (CANH) G Combination Meter Assembly (V1 Bus)
      F83-18 (CANL) W
      F83-8 (CANH) V Air Conditioning Amplifier Assembly (V1 Bus)*8
      F83-19 (CANL) W
      F83-10 (CANH) SB No. 1 Junction Connector (V1 Bus)
      F83-21 (CANL) W

      • *2 : w/ Entry and Start System

      • *6 : w/ VSC

      • *7 : w/ Radio and Display System

      • *8 : w/ Air Conditioning System or Electrical Type Power Heater System

  3. CHECK DLC3

    A005MBGE02

    1. Turn the ignition switch off.

    2. Measure the resistance according to the value(s) in the table below.

      for V1 Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      F4-6 (CANH) - F4-14 (CANL) GR - W Ignition switch off 54 to 69 Ω
      F4-6 (CANH) - F4-16 (BAT) GR - BE Ignition switch off 6 kΩ or higher
      F4-14 (CANL) - F4-16 (BAT) W - BE Ignition switch off 6 kΩ or higher
      F4-6 (CANH) - F4-4 (CG) GR - W-B Ignition switch off 200 Ω or higher
      F4-14 (CANL) - F4-4 (CG) W - W-B Ignition switch off 200 Ω or higher

  4. CHECK ECM (for 1NR-FE and 1NZ-FE)

    A005GEVE01
    Text in Illustration
    *A for RHD *B for LHD

    1. Disconnect the A58 ECM and B23*1 or B22*2 ECM connectors.

    2. Measure the resistance according to the value(s) in the table below.

      for V1 Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A58-13 (CANH) - A58-26 (CANL) L - W Ignition switch off 108 to 132 Ω
      A58-13 (CANH) - A58-2 (+B) L - B Ignition switch off 6 kΩ or higher
      A58-26 (CANL) - A58-2 (+B) W - B Ignition switch off 6 kΩ or higher

      A58-13 (CANH) - B23-16 (E1)*1

      A58-13 (CANH) - B22-16 (E1)*2

      		 L - W-B Ignition switch off 200 Ω or higher

      A58-26 (CANL) - B23-16 (E1)*1

      A58-26 (CANL) - B22-16 (E1)*2

      		 W - W-B Ignition switch off 200 Ω or higher
      for Power Train Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A58-12 (CANP) - A58-25 (CANN) B - W Ignition switch off 108 to 132 Ω
      A58-12 (CANP) - A58-2 (+B) B - B Ignition switch off 6 kΩ or higher
      A58-25 (CANN) - A58-2 (+B) W - B Ignition switch off 6 kΩ or higher

      A58-12 (CANP) - B22-16 (E1)*2

      A58-12 (CANP) - B23-16 (E1)*3

      		 B - W-B Ignition switch off 200 Ω or higher

      A58-25 (CANN) - B22-16 (E1)*2

      A58-25 (CANN) - B23-16 (E1)*3

      		 W - W-B Ignition switch off 200 Ω or higher

    *1 : for RHD

    *2 : for LHD

    *3 : for RHD with Rear Fog Light

  5. CHECK ECM (for 1ND-TV)

    A005M6AE01

    1. Disconnect the A59 ECM connectors.

    2. Measure the resistance according to the value(s) in the table below.

      for V1 Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A59-3 (CANH) - A59-4 (CANL) L - W Ignition switch off 108 to 132 Ω
      A59-3 (CANH) - A59-1 (+B) L - B Ignition switch off 6 kΩ or higher
      A59-4(CANL) - A59-1 (+B) W - B Ignition switch off 6 kΩ or higher
      A59-3 (CANH) - A59-2 (E1) L - W-B Ignition switch off 200 Ω or higher
      A59-4 (CANL) - A59-2 (E1) W - W-B Ignition switch off 200 Ω or higher
      for Power Train Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A59-17 (CANP) - A59-16 (CANN) B - W Ignition switch off 108 to 132 Ω
      A59-17 (CANP) - A59-1 (+B) B - B Ignition switch off 6 kΩ or higher
      A59-16 (CANN) - A59-1 (+B) W - B Ignition switch off 6 kΩ or higher
      A59-17 (CANP) - A59-2 (E1) B - W-B Ignition switch off 200 Ω or higher
      A59-16 (CANN) - A59-2 (E1) W - W-B Ignition switch off 200 Ω or higher

  6. CHECK POWER MANAGEMENT CONTROL ECU (for Rear Fog Light without Stop and Start System)

    A005JCUE01

    1. Disconnect the F74 power management control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      for Power Train Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      F74-4 (CA3P) - F74-3 (CA3N) Y - W Ignition switch off 108 to 132 Ω
      F74-4 (CA3P) - F74-8 (AM21) Y - BE Ignition switch off 6 kΩ or higher
      F74-3 (CA3N) - F74-8 (AM21) W - BE Ignition switch off 6 kΩ or higher
      F74-4 (CA3P) - F74-12 (GND) Y - BR Ignition switch off 200 Ω or higher
      F74-3 (CA3N) - F74-12 (GND) W - BR Ignition switch off 200 Ω or higher

  7. CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU), INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

    A005IYYE01
    Text in Illustration
    *A for LHD *B for RHD
    *C w/ Theft Deterrent System - -
    *1 Instrument Panel Junction Block Assembly *2 Main Body ECU (Multiplex Network Body ECU)

    1. Disconnect the F76 main body ECU (multiplex network body ECU) connector.

    2. Disconnect the 3B and 3C instrument panel junction block assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      for V1 Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      F76-14 (CANH) - F76-13 (CANL) R - W Ignition switch off 54 to 69 Ω
      F76-14 (CANH) - 3C-21 R - L Ignition switch off 6 kΩ or higher
      F76-13 (CANL) - 3C-21 W - L Ignition switch off 6 kΩ or higher
      F76-14 (CANH) - 3B-8 R - W-B Ignition switch off 200 Ω or higher
      F76-13 (CANL) - 3B-8 W - W-B Ignition switch off 200 Ω or higher

  8. CHECK COMBINATION METER ASSEMBLY

    A005GXZE01

    1. Disconnect the F1 combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      for V1 Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      F1-32 (CANH) - F1-31 (CANL) G - W Ignition switch off 108 to 132 Ω
      F1-32 (CANH) - F1-40 (B) G - L Ignition switch off 6 kΩ or higher
      F1-31 (CANL) - F1-40 (B) W - L Ignition switch off 6 kΩ or higher
      F1-32 (CANH) - F1-21 (ET) G - W-B Ignition switch off 200 Ω or higher
      F1-31 (CANL) - F1-21 (ET) W - W-B Ignition switch off 200 Ω or higher

  9. CHECK SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

    A005JB9E02
    Text in Illustration
    *A w/ VSC (except LHD with CVT) *B w/o VSC (except LHD with CVT)
    *C w/ VSC (for LHD with CVT) *D w/o VSC (for LHD with CVT)

    1. Disconnect the A54*1, A55*2, A56*3 or A57*4 skid control ECU (brake actuator assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      for V1 Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition

      A54-25 (CANH) - A54-14 (CANL)*1

      A55-25 (CANH) - A55-14 (CANL)*2

      A56-25 (CANH) - A56-14 (CANL)*3

      A57-25 (CANH) - A57-14 (CANL)*4

      		 G - W Ignition switch off 54 to 69 Ω

      A54-25 (CANH) - A54-12 (+BS)*1

      A55-25 (CANH) - A55-12 (+BS)*2

      A56-25 (CANH) - A56-12 (+BS)*3

      A57-25 (CANH) - A57-12 (+BS)*4

      		 G - W Ignition switch off 6 kΩ or higher

      A54-14 (CANL) - A54-12 (+BS)*1

      A55-14 (CANL) - A55-12 (+BS)*2

      A56-14 (CANL) - A56-12 (+BS)*3

      A57-14 (CANL) - A57-12 (+BS)*4

      		 W - W Ignition switch off 6 kΩ or higher

      A54-25 (CANH) - A54-1 (GND1)*1

      A55-25 (CANH) - A55-1 (GND1)*2

      A56-25 (CANH) - A56-1 (GND1)*3

      A57-25 (CANH) - A57-1 (GND1)*4

      		 G - W-B Ignition switch off 200 Ω or higher

      A54-14 (CANL) - A54-1 (GND1)*1

      A55-14 (CANL) - A55-1 (GND1)*2

      A56-14 (CANL) - A56-1 (GND1)*3

      A57-14 (CANL) - A57-1 (GND1)*4

      		 W - W-B Ignition switch off 200 Ω or higher

    *1 : w/ VSC (except LHD with CVT)

    *2 : w/o VSC (except LHD with CVT)

    *3 : w/ VSC (for LHD with CVT)

    *4 : w/o VSC (for LHD with CVT)

  10. CHECK AIRBAG SENSOR ASSEMBLY

    A005KAME01
    Text in Illustration
    *A w/o VSC *B w/ VSC

    1. Disconnect the F16 airbag sensor assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      for V1 Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      F16-13 (CANH) - F16-22 (CANL) B - W Ignition switch off 54 to 69 Ω
      F16-13 (CANH) - F4-16 (BAT) B - BE Ignition switch off 6 kΩ or higher
      F16-22 (CANL) - F4-16 (BAT) W - BE Ignition switch off 6 kΩ or higher
      F16-13 (CANH) - F4-4 (CG) B - W-B Ignition switch off 200 Ω or higher
      F16-22 (CANL) - F4-4 (CG) W - W-B Ignition switch off 200 Ω or higher

  11. CHECK STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) (w/ VSC)

    A005LX1E01

    1. Disconnect the F30 steering angle sensor (spiral cable sub-assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      for V1 Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      F30-4 (CANH) - F30-3 (CANL) P - W Ignition switch off 54 to 69 Ω
      F30-4 (CANH) - F30-6 (BAT) P - SB Ignition switch off 6 kΩ or higher
      F30-3 (CANL) - F30-6 (BAT) W - SB Ignition switch off 6 kΩ or higher
      F30-4 (CANH) - F30-2 (ESS) P - BR Ignition switch off 200 Ω or higher
      F30-3 (CANL) - F30-2 (ESS) W - BR Ignition switch off 200 Ω or higher

  12. CHECK POWER STEERING ECU ASSEMBLY

    A005HU7E01

    1. Disconnect the A42 and F6 power steering ECU assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      for V1 Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      F6-7 (CANH) - F6-8 (CANL) LG - W Ignition switch off 54 to 69 Ω
      F6-7 (CANH) - A42-1 (PIG) LG - W Ignition switch off 6 kΩ or higher
      F6-8 (CANL) - A42-1 (PIG) W - W Ignition switch off 6 kΩ or higher
      F6-7 (CANH) - A42-2 (PGND) LG - W-B Ignition switch off 200 Ω or higher
      F6-8 (CANL) - A42-2 (PGND) W - W-B Ignition switch off 200 Ω or higher

  13. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)

    A005KW9E01

    1. Disconnect the F63 and F65 certification ECU (smart key ECU assembly) connectors.

    2. Measure the resistance according to the value(s) in the table below.

      for V1 Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      F63-14 (CANH) - F63-15 (CANL) L - W Ignition switch off 54 to 69 Ω
      F63-14 (CANH) - F65-2 (+B) L - W Ignition switch off 6 kΩ or higher
      F63-15 (CANL) - F65-2 (+B) W - W Ignition switch off 6 kΩ or higher
      F63-14 (CANH) - F65-11 (E) L - BR Ignition switch off 200 Ω or higher
      F63-15 (CANL) - F65-11 (E) W - BR Ignition switch off 200 Ω or higher

  14. RADIO RECEIVER ASSEMBLY (w/ Radio and Display System)

    A005HY0E01

    1. Disconnect the F45 and F47 radio receiver assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      for V1 Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      F47-9 (CANH) - F47-10 (CANL) BE - W Ignition switch off 54 to 69 Ω
      F47-9 (CANH) - F45-4 (+B1) BE - SB Ignition switch off 6 kΩ or higher
      F47-10 (CANL) - F45-4 (+B1) W - SB Ignition switch off 6 kΩ or higher
      F47-9 (CANH) - F45-7 (GND1) BE - BR Ignition switch off 200 Ω or higher
      F47-10 (CANL) - F45-7 (GND1) W - BR Ignition switch off 200 Ω or higher

  15. CHECK ENGINE STOP AND START ECU (w/ Stop and Start System)

    A005LQUE01

    1. Disconnect the A53 and F75 engine stop and start ECU connectors.

    2. Measure the resistance according to the value(s) in the table below.

      for V1 Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      F75-2 (CA1H) - F75-1 (CA1L) BE - W Ignition switch off 54 to 69 Ω
      F75-2 (CA1H) - A53-13 (AM21) BE - B Ignition switch off 6 kΩ or higher
      F75-1 (CA1L) - A53-13 (AM21) W - B Ignition switch off 6 kΩ or higher
      F75-2 (CA1H) - F75-6 (GND) BE - BR Ignition switch off 200 Ω or higher
      F75-1 (CA1L) - F75-6 (GND) W - BR Ignition switch off 200 Ω or higher
      for Local Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A53-2 (CA3P) - A53-1 (CA3N) B - W Ignition switch off 108 to 132 Ω
      A53-2 (CA3P) - A53-13 (AM21) B - B Ignition switch off 6 kΩ or higher
      A53-1 (CA3N) - A53-13 (AM21) W - B Ignition switch off 6 kΩ or higher
      A53-2 (CA3P) - F75-6 (GND) B - BR Ignition switch off 200 Ω or higher
      A53-1 (CA3N) - F75-6 (GND) W - BR Ignition switch off 200 Ω or higher

  16. CHECK TCM (w/ Multi-mode Manual Transaxle System)

    A005ICDE01

    1. Disconnect the A47 and F68 TCM connectors.

    2. Measure the resistance according to the value(s) in the table below.

      for Power Train Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A47-1 (CAN+) - A47-2 (CAN-) BR - W Ignition switch off 54 to 69 Ω
      A47-1 (CAN+) - F68-1 (+B) BR - BE Ignition switch off 6 kΩ or higher
      A47-2 (CAN-) - F68-1 (+B) W - BE Ignition switch off 6 kΩ or higher
      A47-1 (CAN+) - F68-6 (GND) BR - W-B Ignition switch off 200 Ω or higher
      A47-2 (CAN-) - F68-6 (GND) W - W-B Ignition switch off 200 Ω or higher

  17. CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Air Conditioning System or Electrical Type Power Heater System)

    A005KDVE02

    1. Disconnect the F42*1 or F41*2 air conditioning amplifier assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      for V1 Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition

      F42-11 (TX+) - F42-12 (TX-)*1

      F41-8 (TX+) - F41-9 (TX-)*2

      		 V - W Ignition switch off 54 to 69 Ω

      F42-11 (TX+) - F42-21 (B)*1

      F41-8 (TX+) - F4-16 (BAT)*2

      		 V - BE Ignition switch off 6 kΩ or higher

      F42-12 (TX-) - F42-21 (B)*1

      F41-9 (TX-) - F4-16 (BAT)*2

      		 W - BE Ignition switch off 6 kΩ or higher

      F42-11 (TX+) - F42-14 (GND)*1

      F41-8 (TX+) - F41-23 (GND)*2

      		 V - W-B Ignition switch off 200 Ω or higher

      F42-12 (TX-) - F42-14 (GND)*1

      F41-9 (TX-) - F41-23 (GND)*2

      		 W - W-B Ignition switch off 200 Ω or higher

      • *1 : w/ Automatic Air Conditioning System

      • *2 : w/ Manual Air Conditioning System or Electrical Type Power Heater System