AUDIO AND VISUAL SYSTEM(for Radio and Display Type) Speaker Circuit

DESCRIPTION

If there is a short in this circuit, the radio receiver detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the radio receiver or speakers.

If a short is detected in the speaker circuit, no sound can be heard from the speakers.

WIRING DIAGRAM

A005JB0E05

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR


    1. Disconnect the F45 and F46 radio and display assembly connectors.

    2. Disconnect the H8 and G8 front No. 1 speaker assembly connectors.

    3. Disconnect the H9 and G9 front No. 2 speaker assembly connectors (for 6 speakers).

    4. Disconnect the J4 and I4 rear speaker assembly connectors.

    5. Measure the resistance between each of the front No. 2 speaker assembly and the radio and display assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F45-2 (FL+) - H9-4 (+) Always Below 1 Ω
      F45-6 (FL-) - H9-2 (-) Always Below 1 Ω
      F45-1 (FR+) - G9-4 (+) Always Below 1 Ω
      F45-5 (FR-) - G9-2 (-) Always Below 1 Ω

    6. Measure the resistance between each of the front No. 1 speaker assembly and front No. 2 speakers to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H9-3 (TWL+) - H8-1 Always Below 1 Ω
      H9-1 (TWL-) - H8-2 Always Below 1 Ω
      G9-3 (TWR+) - G8-1 Always Below 1 Ω
      G9-1 (TWR-) - G8-2 Always Below 1 Ω

    7. Measure the resistance between each of the rear speaker assembly and the radio and display assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F46-2 (RL+) - J4-1 Always Below 1 Ω
      F46-6 (RL-) - J4-2 Always Below 1 Ω
      F46-1 (RR+) - I4-1 Always Below 1 Ω
      F46-3 (RR-) - I4-2 Always Below 1 Ω

    8. Measure the resistance between each speaker assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H8-1 - Body ground Always 10 kΩ or higher
      H8-2 - Body ground Always 10 kΩ or higher
      G8-1 - Body ground Always 10 kΩ or higher
      G8-2 - Body ground Always 10 kΩ or higher
      H9-4 (+) - Body ground Always 10 kΩ or higher
      H9-2 (-) - Body ground Always 10 kΩ or higher
      G9-4 (+) - Body ground Always 10 kΩ or higher
      G9-2 (-) - Body ground Always 10 kΩ or higher
      J4-1 - Body ground Always 10 kΩ or higher
      J4-2 - Body ground Always 10 kΩ or higher
      I4-1 - Body ground Always 10 kΩ or higher
      I4-2 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Inspect the front No. 1 speaker assembly Click here.

      Tech Tips

      The speaker should not be removed to check resistance.


    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  3. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Check that the malfunction disappears when another speaker in good condition is installed.

      OK
      Malfunction disappears.

      Tech Tips


      • Connect all the connectors to the front No. 2 speakers.

      • If there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both LH and RH sides.


    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  4. INSPECT REAR SPEAKER ASSEMBLY


    1. Inspect the rear speaker assembly Click here.

      Tech Tips

      The speaker should not be removed to check resistance.


    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here