MULTI-MODE MANUAL TRANSAXLE SYSTEM FAIL-SAFE CHART


  1. FAIL-SAFE CHART


    1. If any of the following codes is recorded, the TCM enters the fail-safe mode.

      DTC No. Malfunction Area Fail-safe Function Fail-safe Deactivation Condition

      • P0806

      • P0807

      • P0808

      • P0810

      • P0900

      • Clutch stroke sensor or its circuit

      • Clutch actuator assembly or its circuit

      • Hydraulic pressure clutch system

      • Gear does not change

      • Vehicle does not start moving again after stopping

      Either (a) or (b) met:


      • (a) All of following conditions met:


        • Pass condition detected

        • Shift lever in N position

        • Transaxle gear in neutral*

        • Vehicle speed less than 6 km/h (3.73 mph)

      • (b) Pass condition detected and ignition switch off

      • P0807

      • P0808

      • P0906

      • P0907

      • P0916

      • P0917

      • Clutch stroke sensor or its circuit

      • Select stroke sensor or its circuit

      • Shift stroke sensor or its circuit

      		 Limit to 3rd gears or lower

      Either (a) or (b) met:


      • (a) All of the following conditions met:


        • Pass condition detected

        • Shift lever in N position

        • Transmission gear in neutral*

        • Vehicle speed less than 6 km/h (3.73 mph)

      • (b) Pass condition detected and ignition switch off

      • P0905

      • P0906

      • P0907

      • P0909

      • P0910

      • P0915

      • P0916

      • P0917

      • P0919

      • P0920

      • Shift stroke sensor or its circuit

      • Shift actuator assembly or its circuit

      • Select stroke sensor or its circuit

      • Select actuator assembly or its circuit

      • Gear does not change

      • Vehicle does not start moving again after stopping

      Either (a) or (b) met:


      • (a) All of following conditions met:


        • Pass condition detected

        • Shift lever in N position

        • Vehicle speed less than 6 km/h (3.75 mph)

      • (b) Pass condition detected and ignition switch off
      P0725 Engine speed input circuit

      • Convert engine revolution signals into CAN communication signals

      • No effect

      Either (a) or (b) met:


      • (a) All of following conditions met:


        • Pass condition detected

        • Actual gear position not in neutral

        • Clutch engaged

      • (b) Pass condition detected and ignition switch off

      • P0500

      • P0715

      • Vehicle speed sensor or its circuit

      • Transmission revolution sensor or its circuit

      • Gear does not shift down while driving

      • Only possible to drive in 1st or reverse gears after vehicle stops

      Either (a) or (b) met:


      • (a) All of following conditions met:


        • Pass condition detected

        • Vehicle speed less than 6 km/h (3.73 mph)

        • Accelerator pedal released

        • Brake pedal depressed

      • (b) Pass condition detected and ignition switch off

      • P0603

      • P0885

      • TCM

      • Clutch actuator, shift actuator, select actuator power source circuit

      • Gear does not change

      • Engine cannot be started

      • TCM stops engine when vehicle stops

      		 Pass condition detected and ignition switch off
      P0820

      • Shift lever position sensor or its circuit

      • Transmission shift main switch or its circuit

      • Impossible to enter M-mode

      • Gear does not shift to 1st or reverse (and forward or backward gears)

      		 Pass condition detected and ignition switch off
      P0335 Crankshaft position sensor or its circuit

      Gear does not change

      (Only E ←→ N ←→ R is possible)

      		 Pass condition detected and ignition switch off
      U0100 CAN communication signal circuit

      • Gear does not change

      • Only possible to drive in 1st or reverse gears after vehicle stops

      Either (a) or (b) met:


      • (a) All of following conditions met:


        • Pass condition detected

        • Vehicle stopped

        • Accelerator pedal released

        • Brake pedal depressed

      • (b) Pass condition detected and ignition switch off

      Tech Tips


      • *: Transaxle gear: Actual transaxle gear position

      • The TCM identifies the actual transaxle gear position through the signals from the shift stroke sensor and select stroke sensor.

      • The TCM identifies the shift lever position through the signal from the shift lever position sensor.