SFI SYSTEM, Diagnostic DTC:P0403

DTC Code DTC Name
P0403 Exhaust Gas Recirculation Control Circuit

DESCRIPTION

Refer to DTC P0401 Click here.

DTC No. DTC Detection Condition Trouble Area
P0403 Open or short in EGR valve circuit (1 trip detection logic)

  • Open or short in EGR valve assembly circuit

  • EGR valve assembly

  • ECM

MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the EGR valve assembly circuit.

Example:


MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A005KEVE26

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the ignition switch off and wait for at least 30 seconds.

  5. Turn the ignition switch to ON and turn the GTS on [A].

  6. Start the engine and warm it up [B].

  7. Drive the vehicle at 20 km/h (12 mph) or more for 10 minutes [C].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

  9. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  11. Input the DTC: P0403.

  12. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

WIRING DIAGRAM

A005JBAE01

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.

      Tech Tips

      The A/C switch and all accessory switches should be off.

    5. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / All Data / MAP.

    6. Check the engine idling condition and MAP values in the Data List while performing the Active Test.

      Tech Tips


      • Do not leave the EGR valve open for 10 seconds or more during the Active Test.

      • Be sure to return the EGR valve to step 0 when the Active Test is completed.

      • Do not open the EGR valve 30 steps or more during the Active Test.

      OK
      MAP and idling condition change in response to EGR step position.
      Standard
      - EGR Step Position (Active Test)
      0 Steps 0 to 30 Steps
      Idling condition Steady idling Idling changes from steady to rough idling or engine stalls

      MAP

      (Data List)

      MAP value is 20 to 48 kPa(abs) [150 to 360 mmHg(abs)]

      (EGR valve is fully closed)

      		 MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed
      Result
      Result Proceed to
      NG A
      OK B

      Tech Tips

      During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.


    B

    CHECK FOR INTERMITTENT PROBLEMS Click here

    A

  2. INSPECT EGR VALVE ASSEMBLY


    1. Inspect the EGR valve assembly Click here.

      Tech Tips

      Perform "Inspection After Repair" after replacing the EGR valve assembly Click here.


    NG

    REPLACE EGR VALVE ASSEMBLY Click here

    OK

  3. CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY)


    1. A005H1QE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to EGR Valve Assembly)

      Disconnect the EGR valve assembly connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      B56-2 (+B1) - Body ground Ignition switch ON 11 to 14 V
      B56-5 (+B2) - Body ground Ignition switch ON 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (EGR VALVE ASSEMBLY - NO. 1 INTEGRATION RELAY)

    OK

  4. CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)


    1. Disconnect the EGR valve assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B56-4 (EGR1) - B23-28 (EGR1) Always Below 1 Ω
      B56-3 (EGR2) - B23-27 (EGR2) Always Below 1 Ω
      B56-6 (EGR3) - B23-26 (EGR3) Always Below 1 Ω
      B56-1 (EGR4) - B23-25 (EGR4) Always Below 1 Ω
      B56-4 (EGR1) or B23-28 (EGR1) - Body ground Always 10 kΩ or higher
      B56-3 (EGR2) or B23-27 (EGR2) - Body ground Always 10 kΩ or higher
      B56-6 (EGR3) or B23-26 (EGR3) - Body ground Always 10 kΩ or higher
      B56-1 (EGR4) or B23-25 (EGR4) - Body ground Always 10 kΩ or higher

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR