LIGHTING SYSTEM DATA LIST / ACTIVE TEST
-
DATA LIST
Tech Tips
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
-
Connect the intelligent tester to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the intelligent tester on.
-
Enter the following menus: Body / (desired system) / Data List.
-
According to the display on the intelligent tester, read the Data List.
Main Body Tester Display Measurement Item/Range Normal Condition Diagnostic Note Parking Brake SW Parking brake switch signal / ON or OFF ON: Parking brake applied
OFF: Parking brake released
- Dimmer SW Dimmer switch high signal / ON or OFF ON: Dimmer switch in high or high flash position
OFF: Dimmer switch in low position
- Passing Light SW Dimmer switch high flash signal / ON or OFF ON: Dimmer switch in high flash position
OFF: Dimmer switch not in high flash position
- Rear Fog Light SW Rear fog light switch signal / ON or OFF ON: Rear fog light switch on position
OFF: Rear fog light switch off position
- Front Fog Light SW Front fog light switch signal / ON or OFF ON: Front fog light switch on position
OFF: Front fog light switch off position
- Auto Light SW Light control switch AUTO signal / ON or OFF ON: Light control switch in AUTO position
OFF: Light control switch not in AUTO position
- Head Light SW (Head) Light control switch HEAD signal / ON or OFF ON: Light control switch in HEAD position
OFF: Light control switch not in HEAD position
- Head Light SW (Tail) Light control switch TAIL signal / ON or OFF ON: Light control switch in TAIL or HEAD position
OFF: Light control switch not in TAIL or HEAD position
- Illumination Rate Info Illumination rate information / 0 ms. to 99.99 ms. Condition value will be displayed - Response Time Delay timing of lighting the taillights when the automatic light control sensor detects brightness change / 1.0 s or 0.1 s Customized setting displayed - Sensitivity Sensitivity of the automatic light control system / Light2, Light1, Normal, Dark1 or Dark2 Customized setting displayed - Disp Ex ON Sen Ambient brightness level required to dim display lights (combination meter, navigation display etc.) / Light2, Light1, Normal, Dark1 or Dark2 Customized setting displayed - Disp Ex OFF Sen Ambient brightness level required to cancel dimming display lights (combination meter, navigation display etc.) / Light2, Light1, Normal, Dark1 or Dark2 Customized setting displayed - DRL Function Daytime running light system / ON or OFF Customized setting displayed - Follow Me Home Lighting Time Changes the lighting time of the follow me home system / 30 s,60 s, 90s, or 120s Customized setting displayed - HL Auto Leveling Tester Display Measurement Item/Range Normal Condition Diagnostic Note Headlight Low Beam State Low beam headlight state / ON or OFF ON: Low beam headlights on
OFF: Low beam headlights off
- +B Ignition power supply voltage value / 0 to 19.75 V 11 to 14 V - Height Sens Pw Supply Val Rear height control sensor power supply value / 0 to 5 V Approx. 5.0 V - Rr Height Sens Signal Val Rear height control sensor signal value / 0 to 5 V Approx. 2.5 V - Vehicle Speed Vehicle speed / 0 to 327.67 km/h Actual vehicle speed - Rear Height Adjust Valid Flag Result of rear vehicle height calibration / VALID or INVALID VALID: Rear vehicle height calibration completed
INVALID: Rear vehicle height calibration not completed
- Init Writing Count Number of times initialization performed / 0 to 255 Current condition displayed - Sensor Initialization Hist Sensor initialization history / not comp, 10%, 25%, 50%, 75%, 100% or complied Current condition displayed - Number of trouble cords Number of trouble cords / 0 to 255 Current condition displayed - Combination Meter Tester Display Measurement Item/Range Normal Condition Diagnostic Note Turn Signal Switch (Right) Turn signal switch signal (turn right) / ON or OFF ON: Turn signal switch right on (turn right)
OFF: Turn signal switch right off (turn right)
- Turn Signal Switch (Left) Turn signal switch signal (turn left) / ON or OFF ON: Turn signal switch left on (turn left)
OFF: Turn signal switch left off (turn left)
- Hazard Flasher Switch Hazard warning signal switch / ON or OFF ON: Hazard warning signal switch on
OFF: Hazard warning signal switch off
-
-
-
ACTIVE TEST
Tech Tips
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
-
Connect the intelligent tester to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the intelligent tester on.
-
Enter the following menus: Body / (desired system) / Active Test.
-
According to the display on the intelligent tester, perform the Active Test.
Main Body Tester Display Test Part Control Range Diagnostic Note Taillight Relay Taillight relay ON/OFF - Headlight Relay Low beam headlight relay ON/OFF - Head Light Hi Headlight dimmer relay ON/OFF - Front Fog Light Relay Front fog light relay ON/OFF Light Control switch is in TAIL position Rear Fog Light Relay Rear fog light relay ON/OFF Light Control switch is in TAIL position HL Auto Leveling Tester Display Test Part Control Range Diagnostic Note Drive The Leveling Motor UP Leveling motor ON/OFF - Drive The Leveling Motor DOWN Leveling motor ON/OFF -
-