OUTER REAR VIEW MIRROR INSPECTION

PROCEDURE

1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Check the operation of the outer rear view mirror assembly. (w/o Retract Mirror)

      
      

      1. Apply battery voltage and check the operation of the outer rear view mirror assembly.

         OK

         Measurement Condition Specified Condition Battery positive (+) → Terminal 5 (MV) Battery negative (-) → Terminal 4 (M+) Turns upward Battery positive (+) → Terminal 4 (M+) Battery negative (-) → Terminal 5 (MV) Turns downward Battery positive (+) → Terminal 4 (M+) Battery negative (-) → Terminal 3 (MH) Turns left Battery positive (+) → Terminal 3 (MH) Battery negative (-) → Terminal 4 (M+) Turns right

         If the result is not as specified, replace the outer rear view mirror assembly.

   2. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Check the operation of the outer rear view mirror assembly. (w/ Retract Mirror)

      
      

      1. Apply battery voltage and check the operation of the outer rear view mirror assembly.

         OK

         Measurement Condition Specified Condition Battery positive (+) → Terminal 3 (MV) Battery negative (-) → Terminal 7 (M+) Turns upward Battery positive (+) → Terminal 7 (M+) Battery negative (-) → Terminal 3 (MV) Turns downward Battery positive (+) → Terminal 6 (MH) Battery negative (-) → Terminal 7 (M+) Turns left Battery positive (+) → Terminal 7 (M+) Battery negative (-) → Terminal 6 (MH) Turns right

         If the result is not as specified, replace the outer rear view mirror assembly.

   3. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Check the mirror heater. (w/ Mirror Heater)

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 2 (+) - 1 (-) 25°C (75°F) 8 to 11 Ω

         If the result is not as specified, replace the outer rear view mirror assembly.

2. INSPECT OUTER MIRROR RETRACTOR LH (w/ Retract Mirror)

   

   Text in Illustration

   *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

   
   

   1. Check the retractable mirror's movement.

      
      

      1. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

         OK

         Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal 1 (MR) Battery negative (-) → Terminal 2 (MF) Forward position A Moves from A to retracted position E Battery positive (+) → Terminal 2(MF) Battery negative (-) → Terminal 1 (MR) Forward position A Does not move Battery positive (+) → Terminal 1(MR) Battery negative (-) → Terminal 2 (MF) Position between forward position A and driving position C Moves from B to retracted position E Battery positive (+) → Terminal 2 (MF) Battery negative (-) → Terminal 1 (MR) Position between forward position A and driving position C Moves from B to forward position A Battery positive (+) → Terminal 1 (MR) Battery negative (-) → Terminal 2 (MF) Driving position C Moves from C to retracted position E Battery positive (+) → Terminal 2 (MF) Battery negative (-) → Terminal 1 (MR) Driving position C Does not move Battery positive (+) → Terminal 1 (MR) Battery negative (-) → Terminal 2 (MF) Position between driving position C and retracted position E Moves from D to retracted position E Battery positive (+) → Terminal 2 (MF) Battery negative (-) → Terminal 1 (MR) Position between driving position C and retracted position E Moves from D to retracted position E Battery positive (+) → Terminal 1 (MR) Battery negative (-) → Terminal 2 (MF) Retracted position E Does not move Battery positive (+) → Terminal 2 (MF) Battery negative (-) → Terminal 1 (MR) Retracted position E Moves from E to driving position C

         Note

         
         

         • Disconnect and reconnect the battery between each mirror position check.

         • The mirror position cannot be changed manually when the battery is connected.

         • To change the mirror position manually, the battery must be disconnected first.

         If the result is not as specified, replace the mirror assembly.

3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Check the outer rear view mirror operation. (w/o Retract Mirror)

      
      

      1. Apply battery voltage and check the operation of the outer rear view mirror assembly.

         OK

         Measurement Condition Specified Condition Battery positive (+) → Terminal 5 (MV) Battery negative (-) → Terminal 4 (M+) Turns upward Battery positive (+) → Terminal 4 (M+) Battery negative (-) → Terminal 5 (MV) Turns downward Battery positive (+) → Terminal 3 (MH) Battery negative (-) → Terminal 4 (M+) Turns left Battery positive (+) → Terminal 4 (M+) Battery negative (-) → Terminal 3 (MH) Turns right

         If the result is not as specified, replace the outer rear view mirror assembly.

   2. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Check the outer rear view mirror operation. (w/ Retract Mirror)

      
      

      1. Apply battery voltage and check the operation of the outer rear view mirror assembly.

         OK

         Measurement Condition Specified Condition Battery positive (+) → Terminal 3 (MV) Battery negative (-) → Terminal 7 (M+) Turns upward Battery positive (+) → Terminal 7 (M+) Battery negative (-) → Terminal 3 (MV) Turns downward Battery positive (+) → Terminal 6 (MH) Battery negative (-) → Terminal 7 (M+) Turns left Battery positive (+) → Terminal 7 (M+) Battery negative (-) → Terminal 6 (MH) Turns right

         If the result is not as specified, replace the outer rear view mirror assembly.

   3. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Check the mirror heater. (w/ Mirror Heater)

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 2 (+) - 1 (-) 25°C (75°F) 8 to 11 Ω

         If the result is not as specified, replace the outer rear view mirror assembly.

4. INSPECT OUTER MIRROR RETRACTOR RH (w/ Retract Mirror)

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Check the retractable mirror's movement.

      
      

      1. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

         OK

         Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal 1 (MR) Battery negative (-) → Terminal 2 (MF) Forward position A Moves from A to retracted position E Battery positive (+) → Terminal 2 (MF) Battery negative (-) → Terminal 1 (MR) Forward position A Does not move Battery positive (+) → Terminal 1 MR) Battery negative (-) → Terminal 2 (MF) Position between forward position A and driving position C Moves from B to retracted position E Battery positive (+) → Terminal 2 (MF) Battery negative (-) → Terminal 1 (MR) Position between forward position A and driving position C Moves from B to forward position A Battery positive (+) → Terminal 1 (MR) Battery negative (-) → Terminal 2 (MF) Driving position C Moves from C to retracted position E Battery positive (+) → Terminal 2 (MF) Battery negative (-) → Terminal 1 (MR) Driving position C Does not move Battery positive (+) → Terminal 1 (MR) Battery negative (-) → Terminal 2 (MF) Position between driving position C and retracted position E Moves from D to retracted position E Battery positive (+) → Terminal 2 (MF) Battery negative (-) → Terminal 1 (MR) Position between driving position C and retracted position E Moves from D to retracted position E Battery positive (+) → Terminal 1 (MR) Battery negative (-) → Terminal 2 (MF) Retracted position E Does not move Battery positive (+) → Terminal 2 (MF) Battery negative (-) → Terminal 1 (MR) Retracted position E Moves from E to driving position C

         Note

         
         

         • Disconnect and reconnect the battery between each mirror position check.

         • The mirror position cannot be changed manually when the battery is connected.

         • To change the mirror position manually, the battery must be disconnected first.

         If the result is not as specified, replace the mirror assembly.