СИСТЕМА SFI, Diagnostic DTC:P0016, P0018

Информация добавлена 08-08-2017

DTC Code DTC Name
P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)
P0018 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)

DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the intake camshaft and camshaft timing oil control valve assembly (for intake side), and operating the camshaft timing gear assembly; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) Deviation in the crankshaft position sensor signal and VVT sensor (for intake side of bank 1) signal (2 trip detection logic).

  • Valve timing

  • Camshaft timing oil control valve assembly (for intake side of bank 1)

  • Oil control valve filter (RH)

  • Oil pipe

  • Camshaft timing gear assembly (bank 1)

  • ECM

 Comes on DTC stored
P0018 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A) Deviation in the crankshaft position sensor signal and VVT sensor (for intake side of bank 2) signal (2 trip detection logic).

  • Valve timing

  • Camshaft timing oil control valve assembly (for intake side of bank 2)

  • Oil control valve filter (LH)

  • Oil pipe

  • Camshaft timing gear assembly (bank 2)

  • ECM

 Comes on DTC stored

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM stores DTC P0016 (bank 1) or P0018 (bank 2).

CONFIRMATION DRIVING PATTERN

B001SKZE50

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the engine switch off and wait for at least 30 seconds.

  5. Turn the engine switch on (IG) and turn the GTS on [A].

  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

  7. Idle the engine for 5 minutes or more [C].

  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

  9. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is output, the system is malfunctioning.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  11. Input the DTC: P0016 or P0018.

  12. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

  13. Drive the vehicle for 2 to 3 minutes [E].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Idle the engine for 5 minutes or more [F].

  15. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [G].

  16. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  17. Check the DTC judgment result.

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

CAUTION / NOTICE / HINT

Tech Tips


  • Bank 1 refers to the bank that includes the No. 1 cylinder*.

    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.

  • Bank 2 refers to the bank that does not include the No. 1 cylinder.

  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016 OR P0018)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


      Powertrain > Engine and ECT > Trouble Codes

    5. Read the DTCs.

      Result
      Result Proceed to
      DTC P0016 or P0018 is output A
      DTC P0016 or P0018 and other DTCs are output B

      Tech Tips

      If any DTCs other than P0016 or P0018 are output, troubleshoot those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)

    Tech Tips

    If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2) / Ptrl Valve Control / VVT Change Angle #1 or VVT Change Angle #2.


      Powertrain > Engine and ECT > Active Test
      Tester Display
      Control the VVT Linear (Bank1)

      Powertrain > Engine and ECT > Active Test
      Tester Display
      Control the VVT Linear (Bank2)

    5. Perform the Active Test. Check that the displacement angle varies.

      OK
      Displacement angle varies.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE) Click here

    OK

  3. ADJUST VALVE TIMING


    1. Adjust the valve timing.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 7 Click here

  4. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE)


    1. Inspect the camshaft timing oil control valve assembly (for intake side).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE) Click here

    OK

  5. INSPECT OIL CONTROL VALVE FILTER AND PIPE


    1. B001TQUC02
      *A Bank 2
      *B Bank 1
      *1 No. 1 Oil Pipe
      *2 No. 2 Oil Pipe

      Remove the No. 1 oil pipe or No. 2 oil pipe.

      Click here

    2. Remove the oil control valve filter RH or oil control valve filter LH.

    3. Check that the oil control valve filter and oil pipe are not clogged.

      OK
      The oil control valve filter or oil pipe is not clogged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE OIL CONTROL VALVE FILTER OR OIL PIPE Click here

    OK

  6. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY


    1. Inspect the camshaft timing gear assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CAMSHAFT TIMING GEAR ASSEMBLY Click here

    OK

  7. CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0018)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.

      Click here


      Powertrain > Engine and ECT > Clear DTCs

    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Turn the engine switch on (IG).

    7. Turn the GTS on.

    8. Start the engine and warm it up.

    9. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    10. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


      Powertrain > Engine and ECT > Trouble Codes

    11. Read the pending DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC P0016 or P0018 is output B

    A

    END

    B

    REPLACE ECM Click here