МАСЛО И МАСЛЯНЫЙ ФИЛЬТР ЗАМЕНА

Информация добавлена 08-08-2017

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

  • In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.

PROCEDURE


  1. REMOVE ENGINE UNDER COVER SEAL


    1. Remove the 2 bolts and engine under cover seal.

  2. REMOVE LOWER FRONT BUMPER COVER

    Click here

  3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

    Click here

  4. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the oil pan drain plug and drain the engine oil into a container.

    3. Install a new gasket and the oil pan drain plug.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  5. REMOVE OIL FILTER ELEMENT


    1. A01NAZ0C01
      *1 Pipe
      *2 Hose

      Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

    2. B001OX4

      Remove the oil filter drain plug.

    3. A01NA8VC01
      *1 Cap
      *2 Valve
      *3 Pipe
      *4 O-Ring
      *5 Hose

      Install the pipe to the oil filter cap.

      Note

      If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

      Tech Tips

      Use a container to catch the draining oil.

    4. B001RSQ

      Check that oil is drained from the oil filter. Then, disconnect the pipe and remove the O-ring as shown in the illustration.

    5. A01NBVEC01
      *1 Oil Filter Bracket Clip

      Using SST, remove the oil filter cap.

      SST
      09228-06501

      Note

      Do not remove the oil filter bracket clip.

    6. B001P8PC01
      *1 O-Ring

      Remove the oil filter element and O-ring from the oil filter cap.

      Note

      Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the cap.

  6. INSTALL OIL FILTER ELEMENT


    1. Clean the inside of the oil filter cap, the threads and O-ring

    2. A01NCI7C01
      *1 O-Ring
      *a CORRECT
      *b INCORRECT

      Apply a small amount of engine oil to a new O-ring and install the O-ring to the oil filter cap.

      Note


      • Be sure to install the O-ring in the proper location, otherwise oil may leak.

      • Do not twist the O-ring.

    3. Set a new oil filter element on the oil filter cap.

    4. Remove any dirt or foreign matter from the installation surface of the engine.

    5. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

      Note

      Do not pinch the O-ring for the cap.

    6. A01NCCXC01
      *1 Oil Filter Bracket Clip
      *2 Oil Filler Cap
      *3 O-Ring
      *4 Oil Filter Bracket
      *a No Gap

      Using SST, tighten the oil filter cap.

      SST
      09228-06501
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note


      • When tightening the oil filter cap, do not remove the oil filter bracket clip.

      • After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.

    7. A01NACGC01
      *1 O-Ring

      Apply a small amount of engine oil to a new drain plug O-ring and install the O-ring to the oil filter cap.

      Note

      Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

    8. Install the oil filter drain plug.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

      Note

      Make sure that the O-ring does not get caught between the parts.

  7. ADD ENGINE OIL


    1. Add fresh oil.

      Standard Engine Oil
      Oil Grade Oil Viscosity (SAE)
      API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil

      0W-20

      5W-20

      5W-30

      10W-30
      API grade SL, SM or SN multigrade engine oil

      15W-40

      20W-50
      Standard Oil Capacity
      Item Specified Condition
      Drain and refill without oil filter change 5.7 liters (6.0 US qts, 5.0 Imp. qts)
      Drain and refill with oil filter change 6.2 liters (6.6 US qts, 5.5 Imp. qts)
      Dry fill 7.1 liters (7.5 US qts, 6.2 Imp. qts)

  8. CHECK ENGINE OIL LEVEL

    Click here

  9. INSPECT FOR ENGINE OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.

  10. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

    Click here

  11. INSTALL LOWER FRONT BUMPER COVER

    Click here

  12. INSTALL ENGINE UNDER COVER SEAL


    1. Install the engine under cover seal with the 2 bolts.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }