РАСПРЕДВАЛ УЗЛЫ И ДЕТАЛИ
Информация добавлена 08-08-2017 
ILLUSTRATION
| *1 | ENGINE ROOM SIDE COVER | *2 | ENGINE ROOM SIDE COVER LH |
| *3 | LOWER FRONT BUMPER COVER | *4 | NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY |
| *5 | REAR ENGINE UNDER COVER ASSEMBLY | *6 | TRANSMISSION UNDER COVER |
 |
Specified torque: N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *1 | AIR CLEANER CAP AND HOSE | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | BATTERY | *4 | BATTERY TRAY |
| *5 | UPPER RADIATOR SUPPORT SEAL | *6 | V-BANK COVER SUB-ASSEMBLY |
| *7 | WIRING HARNESS CLAMP BRACKET | *8 | BATTERY HOLD DOWN CLAMP |
| *9 | WIRE HARNESS | *10 | VACUUM HOSE |
| *11 | PCV HOSE | *12 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *1 | FAN SHROUD | *2 | NO. 1 RADIATOR HOSE |
| *3 | NO. 2 RADIATOR HOSE | *4 | OIL COOLER TUBE |
| *5 | RADIATOR RESERVOIR ASSEMBLY | *6 | FAN AND GENERATOR V BELT |
| *7 | FAN PULLEY | *8 | FAN WITH FLUID COUPLING |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *1 | ENGINE OIL LEVEL DIPSTICK GUIDE | *2 | IGNITION COIL ASSEMBLY |
| *3 | INTAKE AIR SURGE TANK | *4 | VANE PUMP ASSEMBLY |
| *5 | NO. 2 SURGE TANK STAY | *6 | NO. 1 VACUUM SWITCHING VALVE CONNECTOR |
| *7 | NO. 1 FUEL VAPOR FEED HOSE | *8 | NO. 1 VENTILATION HOSE |
| *9 | WIRE HARNESS | *10 | NO. 1 SURGE TANK STAY |
| *11 | HEATER WATER HOSE | *12 | NO. 4 WATER BY-PASS HOSE |
| *13 | NO. 5 WATER BY-PASS HOSE | *14 | ENGINE OIL LEVEL DIPSTICK |
| *15 | THROTTLE BODY BRACKET | *16 | THROTTLE BODY CONNECTOR |
| *17 | O-RING | *18 | GASKET |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
| *A | for Separate Type | *B | for Integrated Type |
| *1 | NO. 2 IDLER PULLEY SUB-ASSEMBLY | *2 | IDLER PULLEY COVER PLATE |
| *3 | NO. 2 IDLER PULLEY COVER PLATE | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *1 | CYLINDER HEAD COVER SUB-ASSEMBLY | *2 | CYLINDER HEAD COVER SUB-ASSEMBLY LH |
| *3 | FUEL PIPE SUB-ASSEMBLY | *4 | GENERATOR ASSEMBLY |
| *5 | NO. 1 OIL PIPE | *6 | NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
| *7 | NO. 2 OIL PIPE | *8 | REAR CYLINDER HEAD COVER |
| *9 | WATER BY-PASS PIPE SUB-ASSEMBLY | *10 | SEAL WASHER |
| *11 | CYLINDER HEAD COVER GASKET | *12 | SEAL WASHER |
| *13 | OIL CONTROL VALVE FILTER LH | *14 | OIL CONTROL VALVE FILTER RH |
| *15 | NO. 2 CYLINDER HEAD COVER GASKET | *16 | GENERATOR BRACKET |
| *17 | GASKET | - | |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT | *2 | CAMSHAFT BEARING CAP (for Bank 1) |
| *3 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Bank 1) | *4 | CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 1) |
| *5 | NO. 1 CHAIN SUB-ASSEMBLY | *6 | NO. 1 CHAIN TENSIONER ASSEMBLY |
| *7 | NO. 2 CAMSHAFT | *8 | NO. 3 CAMSHAFT |
| *9 | NO. 4 CAMSHAFT | *10 | TIMING CHAIN COVER PLATE |
| *11 | NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1) | *12 | NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2) |
| *13 | CAMSHAFT BEARING CAP (for Bank 2) | *14 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Bank 2) |
| *15 | NO. 2 CHAIN TENSIONER ASSEMBLY | *16 | NO. 3 CHAIN TENSIONER ASSEMBLY |
| *17 | CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 2) | *18 | GASKET |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |