БЛОК ДВИГАТЕЛЯ УЗЛЫ И ДЕТАЛИ
Информация добавлена 08-08-2017 
ILLUSTRATION
| *A | for Separate Type | *B | for Integrated Type |
| *1 | ENGINE OIL LEVEL DIPSTICK GUIDE | *2 | FRONT NO. 1 ENGINE MOUNTING BRACKET LH |
| *3 | FRONT NO. 1 ENGINE MOUNTING BRACKET RH | *4 | HEATER WATER HOSE ASSEMBLY |
| *5 | IGNITION COIL ASSEMBLY | *6 | NO. 1 IDLER PULLEY SUB-ASSEMBLY |
| *7 | NO. 2 IDLER PULLEY SUB-ASSEMBLY | *8 | REAR CYLINDER HEAD COVER |
| *9 | V-RIBBED BELT TENSIONER ASSEMBLY | *10 | ENGINE OIL LEVEL DIPSTICK |
| *11 | O-RING | *12 | IDLER PULLEY COVER PLATE |
| *13 | NO. 2 IDLER PULLEY COVER PLATE | - | - |
 |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
| *1 | CRANKSHAFT POSITION SENSOR | *2 | ENGINE COOLANT TEMPERATURE SENSOR |
| *3 | ENGINE OIL PRESSURE SWITCH ASSEMBLY | *4 | FUEL DELIVERY PIPE SUB-ASSEMBLY |
| *5 | FUEL INJECTOR ASSEMBLY | *6 | FUEL PIPE SUB-ASSEMBLY |
| *7 | INTAKE MANIFOLD | *8 | GASKET |
| *9 | INJECTOR VIBRATION INSULATOR | *10 | O-RING |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *1 | OIL FILLER CAP HOUSING | *2 | OIL FILTER BRACKET |
| *3 | OIL FILTER ELEMENT | *4 | REAR WATER BY-PASS JOINT |
| *5 | WATER BY-PASS PIPE SUB-ASSEMBLY | *6 | WATER INLET HOUSING |
| *7 | OIL FILLER CAP SUB-ASSEMBLY | *8 | NO. 2 WATER BY-PASS HOSE |
| *9 | NO. 1 WATER BY-PASS HOSE | *10 | O-RING |
| *11 | GASKET | *12 | NO. 3 WATER BY-PASS HOSE |
| *13 | OIL FILTER CAP SUB-ASSEMBLY | *14 | DRAIN PLUG |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY | *2 | CYLINDER HEAD COVER SUB-ASSEMBLY |
| *3 | NO. 2 OIL PIPE | *4 | SPARK PLUG |
| *5 | SPARK PLUG TUBE GASKET | *6 | VVT SENSOR |
| *7 | SEAL WASHER | *8 | O-RING |
| *9 | GASKET | *10 | CYLINDER HEAD COVER GASKET |
| *11 | OIL CONTROL VALVE FILTER RH | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
 |
MP grease | - | - |
ILLUSTRATION
| *1 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY | *2 | CYLINDER HEAD COVER SUB-ASSEMBLY LH |
| *3 | NO. 1 OIL PIPE | *4 | PCV VALVE SUB-ASSEMBLY |
| *5 | SPARK PLUG | *6 | SPARK PLUG TUBE GASKET |
| *7 | VVT SENSOR | *8 | O-RING |
| *9 | SEAL WASHER | *10 | NO. 2 CYLINDER HEAD COVER GASKET |
| *11 | GASKET | *12 | OIL CONTROL VALVE FILTER LH |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| |
MP grease | ★ | Precoated part |
ILLUSTRATION
| *1 | CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY | *2 | ENGINE REAR OIL SEAL RETAINER |
| *3 | NO. 1 OIL PAN BAFFLE PLATE | *4 | NO. 2 OIL PAN SUB-ASSEMBLY |
| *5 | OIL PAN DRAIN PLUG | *6 | OIL PAN SUB-ASSEMBLY |
| *7 | OIL STRAINER SUB-ASSEMBLY | *8 | REAR CRANKSHAFT OIL SEAL |
| *9 | TAPER SCREW PLUG | *10 | O-RING |
| *11 | GASKET | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| |
MP grease | ★ | Precoated part |
ILLUSTRATION
| *1 | CRANKSHAFT PULLEY | *2 | ENGINE WATER PUMP ASSEMBLY |
| *3 | FRONT CRANKSHAFT OIL SEAL | *4 | TIMING CHAIN COVER SUB-ASSEMBLY |
| *5 | TIMING CHAIN COVER PLATE | *6 | GASKET |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| |
MP grease | - | - |
ILLUSTRATION
| *1 | CHAIN TENSIONER SLIPPER | *2 | CRANKSHAFT TIMING SPROCKET |
| *3 | NO. 1 CHAIN SUB-ASSEMBLY | *4 | NO. 1 CHAIN TENSIONER ASSEMBLY |
| *5 | NO. 1 CHAIN VIBRATION DAMPER | *6 | NO. 1 IDLE GEAR SHAFT |
| *7 | NO. 2 CHAIN VIBRATION DAMPER | *8 | NO. 1 IDLE GEAR |
| *9 | NO. 2 IDLE GEAR SHAFT | *10 | O-RING |
| *11 | CRANKSHAFT TIMING GEAR KEY | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT | *2 | CAMSHAFT BEARING CAP (for Bank 1) |
| *3 | CAMSHAFT HOUSING SUB-ASSEMBLY RH | *4 | NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
| *5 | NO. 2 CAMSHAFT | *6 | NO. 2 CHAIN TENSIONER ASSEMBLY |
| *7 | VALVE LASH ADJUSTER ASSEMBLY | *8 | VALVE STEM CAP |
| *9 | NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1) | *10 | GASKET |
| *11 | CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 1) | *12 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY RH (for Bank 1) |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT BEARING CAP (for Bank 2) | *2 | CAMSHAFT HOUSING SUB-ASSEMBLY LH |
| *3 | NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY | *4 | NO. 3 CAMSHAFT |
| *5 | NO. 3 CHAIN TENSIONER ASSEMBLY | *6 | NO. 4 CAMSHAFT |
| *7 | VALVE LASH ADJUSTER ASSEMBLY | *8 | VALVE STEM CAP |
| *9 | CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 2) | *10 | NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2) |
| *11 | GASKET | *12 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY LH (for Bank 2) |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
| *1 | CYLINDER BLOCK WATER JACKET SPACER | *2 | CYLINDER HEAD GASKET |
| *3 | CYLINDER HEAD LH | *4 | CYLINDER HEAD SUB-ASSEMBLY |
| *5 | KNOCK SENSOR | *6 | NO. 1 WATER OUTLET PIPE |
| *7 | NO. 2 CYLINDER HEAD GASKET | *8 | CYLINDER HEAD SET BOLT |
| *9 | KNOCK SENSOR WIRE | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| *T1 | 1st: 36 (367, 27) 2nd: Turn 90° 3rd: Turn 90° |
- | - |