ДВИГАТЕЛЬ В СБОРЕ УЗЛЫ И ДЕТАЛИ
Информация добавлена 08-08-2017 
ILLUSTRATION
| *1 | ENGINE ROOM SIDE COVER | *2 | ENGINE ROOM SIDE COVER LH |
| *3 | LOWER FRONT BUMPER COVER | *4 | NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY |
| *5 | REAR ENGINE UNDER COVER ASSEMBLY | *6 | TRANSMISSION UNDER COVER |
 |
Specified torque: N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *1 | AIR CLEANER CAP AND HOSE | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | BATTERY | *4 | BATTERY TRAY |
| *5 | UPPER RADIATOR SUPPORT SEAL | *6 | V-BANK COVER SUB-ASSEMBLY |
| *7 | WIRING HARNESS CLAMP BRACKET | *8 | BATTERY HOLD DOWN CLAMP |
| *9 | WIRE HARNESS | *10 | VACUUM HOSE |
| *11 | PCV HOSE | *12 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *1 | COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY | *2 | FRONT BUMPER COVER |
| *3 | HOOD SUB-ASSEMBLY | *4 | FRONT WIPER ARM HEAD CAP |
| *5 | FRONT WIPER ARM AND BLADE ASSEMBLY LH | *6 | FRONT WIPER ARM AND BLADE ASSEMBLY RH |
| *7 | FRONT WIPER ARM HEAD CAP | *8 | FRONT FENDER TO COWL SIDE SEAL RH |
| *9 | FRONT FENDER SIDE PANEL PROTECTOR RH | *10 | HOOD TO COWL TOP SEAL |
| *11 | FRONT FENDER SIDE PANEL PROTECTOR LH | *12 | FRONT FENDER TO COWL SIDE SEAL LH |
| *13 | CENTER NO. 2 COWL TOP VENTILATOR LOUVER | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *1 | FAN AND GENERATOR V BELT | *2 | FAN SHROUD |
| *3 | NO. 1 RADIATOR HOSE | *4 | NO. 2 RADIATOR HOSE |
| *5 | OIL COOLER TUBE | *6 | RADIATOR ASSEMBLY |
| *7 | RADIATOR RESERVOIR ASSEMBLY | *8 | RADIATOR SIDE DEFLECTOR LH |
| *9 | RADIATOR SIDE DEFLECTOR RH | *10 | RADIATOR CAP SUB-ASSEMBLY |
| *11 | FAN PULLEY | *12 | FAN WITH FLUID COUPLING |
| *13 | RADIATOR DRAIN COCK PLUG | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *1 | INTAKE AIR SURGE TANK | *2 | NO. 1 VACUUM SWITCHING VALVE CONNECTOR |
| *3 | NO. 1 FUEL VAPOR FEED HOSE | *4 | NO. 1 VENTILATION HOSE |
| *5 | NO. 1 SURGE TANK STAY | *6 | NO. 2 SURGE TANK STAY |
| *7 | NO. 4 WATER BY-PASS HOSE | *8 | NO. 5 WATER BY-PASS HOSE |
| *9 | THROTTLE BODY CONNECTOR | *10 | THROTTLE BODY BRACKET |
| *11 | WIRE HARNESS | *12 | GASKET |
| *13 | HEATER WATER HOSE | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
| *1 | COOLER COMPRESSOR ASSEMBLY | *2 | DISCHARGE HOSE SUB-ASSEMBLY |
| *3 | GENERATOR ASSEMBLY | *4 | SUCTION HOSE SUB-ASSEMBLY |
| *5 | VANE PUMP ASSEMBLY | *6 | O-RING |
| *7 | GENERATOR BRACKET | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
 |
Compressor oil ND-OIL 8 or equivalent | - | - |
ILLUSTRATION
| *A | for Separate Type | *B | for Integrated Type |
| *1 | NO. 2 IDLER PULLEY SUB-ASSEMBLY | *2 | IDLER PULLEY COVER PLATE |
| *3 | NO. 2 IDLER PULLEY COVER PLATE | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *1 | FRONT EXHAUST PIPE ASSEMBLY | *2 | GASKET |
| *3 | COMPRESSION SPRING | *4 | FRONT NO. 2 EXHAUST PIPE ASSEMBLY |
| *5 | EXHAUST PIPE STOPPER BRACKET | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
| *1 | EXHAUST MANIFOLD SUB-ASSEMBLY LH | *2 | EXHAUST MANIFOLD SUB-ASSEMBLY RH |
| *3 | FRONT FENDER APRON SEAL LH | *4 | FRONT FENDER APRON SEAL RH |
| *5 | FRONT NO. 1 FENDER APRON TO FRAME SEAL LH | *6 | FRONT NO. 1 FENDER APRON TO FRAME SEAL RH |
| *7 | MANIFOLD STAY | *8 | NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
| *9 | NO. 2 EXHAUST MANIFOLD HEAT INSULATOR | *10 | NO. 2 MANIFOLD STAY |
| *11 | GASKET | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
| *1 | ENGINE WIRE | *2 | HEATER WATER HOSE ASSEMBLY |
| *3 | NO. 1 FUEL PIPE | *4 | STARTER ASSEMBLY |
| *5 | STARTER COVER | *6 | ECM CONNECTOR |
| *7 | NO. 2 FUEL PIPE CLAMP | *8 | NO. 2 FUEL PIPE |
| *9 | STARTER WIRE | *10 | STARTER CONNECTOR |
| *11 | GROUND WIRE | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *1 | FRONT PROPELLER SHAFT ASSEMBLY | *2 | PROPELLER SHAFT ASSEMBLY |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) |  |
Do not apply lubricants to the threaded parts |
ILLUSTRATION
| *1 | AUTOMATIC TRANSMISSION ASSEMBLY | *2 | DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT |
| *3 | OIL COOLER TUBE ASSEMBLY | *4 | WATER BY-PASS PIPE ASSEMBLY |
| *5 | TRANSMISSION OIL COOLER ASSEMBLY | *6 | WIRE HARNESS AND CONNECTOR |
| *7 | GASKET | *8 | DRAIN PLUG |
| *9 | TRANSMISSION CONTROL CABLE BRACKET | *10 | TRANSMISSION CONTROL CABLE ASSEMBLY |
| *11 | TRANSFER CASE LOWER PROTECTOR | *12 | FRONT SUSPENSION MEMBER BRACKET LH |
| *13 | FRONT SUSPENSION MEMBER BRACKET RH | *14 | REAR NO. 1 ENGINE MOUNTING INSULATOR |
| *15 | REAR NO. 1 ENGINE MOUNTING HEAT INSULATOR | *16 | NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
| *a | Black | *b | Silver |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
| *1 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY | *2 | ENGINE HANGER |
| *3 | FRONT DRIVE PLATE SPACER | *4 | REAR DRIVE PLATE SPACER |
| *5 | FRONT ENGINE MOUNTING INSULATOR RH | *6 | FRONT ENGINE MOUNTING INSULATOR LH |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ★ | Precoated part |