LIGHTING SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuator and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester.

    4. Enter the following menus: Body / (desired system) / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Parking Brake SW Parking brake switch signal/ON or OFF

      ON: Parking brake switch on

      OFF: Parking brake switch off

      		 -
      Hazard Switch Hazard switch signal/ON or OFF

      ON: Hazard switch on

      OFF: Hazard switch off

      		 -
      Dimmer SW Dimmer switch high position signal/ON or OFF

      ON: Dimmer switch in high or high flash position

      OFF: Dimmer switch in low position

      		 -
      Passing Light SW Dimmer switch high flash position (pass) signal/ON or OFF

      ON: Dimmer switch in high flash position

      OFF: Dimmer switch not in high flash position

      		 -
      Rear Fog Light SW Rear fog light switch signal/ON or OFF

      ON: Rear fog light switch on

      OFF: Rear fog light switch off

      		 -
      Front Fog Light SW Front fog light switch signal/ON or OFF

      ON: Front fog light switch on

      OFF: Front fog light switch off

      		 -
      Auto Light SW Light control switch AUTO position signal/ON or OFF

      ON: Light control switch in AUTO position

      OFF: Light control switch not in AUTO position

      		 -
      Head Light SW (Head) Light control switch head position signal/ON or OFF

      ON: Light control switch in head position

      OFF: Light control switch not in head position

      		 -
      Head Light SW (Tail) Light control switch tail position signal/ON or OFF

      ON: Light control switch in tail or head position

      OFF: Light control switch in neither tail nor head position

      		 -
      Illumination Rate Info Illumination rate information/0 ms. to 2162.65 ms. Value is output according to ambient light levels -
      Mirr-Foot-Lgt Approached Lights up the door mirror foot lights when a key enters any actuation area around the doors./ON or OFF Customize setting displayed -
      Mirr-Foot-Lgt Unlocked Lights up the door mirror foot lights when doors are unlocked using a mechanical key or door control transmitter./ON or OFF Customize setting displayed -
      Mirr-Foot-Lgt w/Master SW

      • Lights up the door mirror foot lights when the driver side door control switch on the multiplex network master switch assembly is pushed to the unlock position.

      • Lights up the door mirror foot lights when the driver side door control switch on the multiplex network master switch assembly is pushed to the unlock position./ON or OFF

      		 Customize setting displayed -
      Mirror Foot Light Time Lighting time of the door mirror foot lights/7.5 s, 15 s, 30 s or 0 s Customize setting displayed -
      Exterior Light Control Changes the door mirror foot light control/ON or OFF Customize setting displayed -
      Response Time*1 Delay timing of lighting the taillights when the automatic light control sensor detects brightness change/0.1 s or 1.0 s Customize setting displayed -
      Sensitivity Sensitivity of the automatic light control system/Light2, Light1, Normal, Dark1 or Dark2 Customize setting displayed -
      DRL Function*2 DRL function/ON or OFF Customize setting displayed -
      Disp Ex ON Sen Ambient brightness level required to dim display lights (combination meter, navigation display etc.)/Light2, Light1, Normal, Dark1 or Dark2 Customize setting displayed -
      Disp Ex OFF Sen Ambient brightness level required to cancel dimming display lights (combination meter, navigation display etc.)/Light2, Light1, Normal, Dark1 or Dark2 Customize setting displayed -
      HL Auto Leveling
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Headlight Low Beam State Low beam headlight state/ON or OFF

      ON: Low beam headlights on

      OFF: Low beam headlights off

      		 -
      +B IG power supply voltage value/0 to 19.75 V 11 to 14 V -
      Height Sens Pw Supply Val Height control sensor power supply value/0 to 6.25 V Approx. 5 V -
      Rr Height Sens Signal Val Rear height control sensor signal value/0 to 5 V Approx. 2.5 V (When vehicle is level) Value changes according to vehicle height
      Vehicle Speed Vehicle speed/0 to 327.67 km/h (203.61 mph) Condition can be displayed -
      Rear Height Adjust Valid Flag Rear height adjustment range/VALID or INVALID Condition can be displayed -
      Init Writing Count Number of times for initialization/0 to 255 Condition can be displayed -
      Sensor Initialization Hist Sensor Initialization History/not comp, 10%, 25%, 50%, 75%, 100% or complied Condition can be displayed -
      Number Of Trouble Codes Number of trouble codes/0 to 255 Condition can be displayed -

      • *1: w/o Light Reminder

      • *2: w/ DRL

  2. ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / (desired system) / Active Test.

    5. Perform the Active Test according to the display on the intelligent tester.

      Main Body
      Tester Display Test Part Control Range Diagnostic Note
      Hazard Hazard warning lights ON/OFF -
      Daytime Running Light Daytime running lights ON/OFF -
      Side Mirror Foot Light*1 Door mirror foot lights ON/OFF -
      Taillight Relay Taillight relay ON/OFF -
      Headlight Relay Headlight relays ON/OFF -
      Head Light Hi High beam headlights ON/OFF -
      Front Fog Light Relay Front fog light relay ON/OFF Light control switch is in head position
      Rear Fog Light Relay Rear fog light relay ON/OFF Light control switch is in head position

      *1: w/o Seat Position Memory

      HL Auto Leveling
      Tester Display Test Part Control Range Diagnostic Note
      Drive The Leveling Motor UP*2 Leveling motor upward operation ON/OFF

      ON: Move up

      OFF: Stop
      Drive The Leveling Motor DOWN*2 Leveling motor downward operation ON/OFF

      ON: Move down

      OFF: Stop

      *2: Perform the active test with the power switch on (READY).

      Mirror L*3
      Tester Display Test Part Control Range Diagnostic Note
      Foot Light Door mirror foot light LH ON/OFF -
      Mirror R*3
      Tester Display Test Part Control Range Diagnostic Note
      Foot Light Door mirror foot light RH ON/OFF -

      *3: w/ Seat Position Memory