OUTER REAR VIEW MIRROR REMOVAL


  1. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A003Z3P

      Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.

  2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. A003XX5

      Disengage the clip and claw, and remove the front door lower frame bracket garnish.

  3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A003YE8

      Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides as shown in the illustration.

    2. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.

  4. REMOVE DOOR ARMREST COVER (for Driver Side)


    1. A003W2R

      Remove the door armrest cover.

  5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for Driver Side)


    1. A003Y7TE01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the front door panel.

    2. A003V24

      Remove the 3 screws.

    3. Using a clip remover, disengage the 11 clips.

    4. Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

    5. Raise the front door trim board sub-assembly and remove it.

    6. w/ Seat Position Memory System:


      1. Disconnect the connector.

    7. A003VYA

      Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.

  6. REMOVE DOOR ASSIST GRIP COVER (for Front Passenger Side)


    1. A003WCT

      Using a moulding remover, disengage the 4 claws and guide to remove the door assist grip cover.

  7. REMOVE DOOR ASSIST GRIP ASSEMBLY (for Front Passenger Side)


    1. A003VKE

      Remove the 2 screws.

    2. Disengage the 3 guides and remove the door assist grip assembly.

  8. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A003Z9Y

      Using a moulding remover, disengage the 3 clips, 8 claws and 4 guides as shown in the illustration.

    2. Disconnect each connector and remove the power window regulator switch assembly with front door armrest base panel.

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for Front Passenger Side)


    1. A003XR9E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the front door panel.

    2. A003W3R

      Remove the 2 screws.

    3. Using a clip remover, disengage the 11 clips.

    4. Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

    5. Raise the front door trim board sub-assembly and remove the front door trim board sub-assembly .

    6. A003XTZ

      Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.

  10. REMOVE OUTER MIRROR INSTALL HOLE COVER


    1. A003Z3G

      Remove the screw.

    2. Disengage the 2 claws.

    3. Disengage the clamp and remove the outer mirror install hole cover.

  11. REMOVE OUTER MIRROR PROTECTOR


    1. A003WZW

      Remove the outer mirror protector.

      Tech Tips

      Remove any remaining adhesive residue on the door.

  12. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY


    1. w/o Memory:


      1. A003W3X

        Disconnect the connector.

      2. Disengage the clamp.

      3. Remove the 3 nuts.

    2. w/ Memory:


      1. A003Z8U

        Disconnect the connector.

      2. Disengage the clamp.

      3. Remove the 3 nuts.

    3. Disengage the claw and remove the outer rear view mirror assembly.