FUEL LID OPENER MOTOR ASSEMBLY INSTALLATION


  1. INSTALL FUEL LID WITH MOTOR LOCK ASSEMBLY


    1. Install the fuel lid with motor lock assembly with the bolt.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Engage the 2 claws.

    3. Connect the connector.

  2. INSTALL NO. 1 SPEAKER ASSEMBLY WITH BOX (w/ Woofer)


    1. A003VQQE01
      Text in Illustration
      *1 Screw

      Temporarily install the screw.

      Note

      Do not touch the speaker cone.

    2. Install the No. 1 speaker assembly with box with the screw and 3 bolts.

      Tech Tips

      Install the screw and bolts in the order shown in the illustration.

    3. Connect the connector.

  3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Engage the 4 claws and 3 clips.

    2. Install the deck trim side panel assembly LH with the 3 screw.

  4. INSTALL TONNEAU COVER HOLDER CAP


    1. A003WAM

      Engage the guide.

    2. Engage the claw to install the tonneau cover holder cap.

  5. INSTALL TONNEAU COVER HOOK


    1. A003YU6

      Engage the 2 claws and pin to install the tonneau cover hook.

  6. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY


    1. Engage the guide.

    2. Install the luggage hold belt striker assembly with the bolt.

  7. INSTALL ROPE HOOK ASSEMBLY


    1. A003W27

      Install the rope hook assembly with the bolt.

    2. Engage the 2 claws.

  8. INSTALL REAR SEAT SIDE GARNISH LH


    1. Engage the 6 claws.

    2. Install the rear seat side garnish LH with the clip.

  9. INSTALL REAR SEATBACK ASSEMBLY LH


    1. Place the rear seatback assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly LH with the 2 bolts.

      Torque:
      37 N*m  { 375 kgf*cm, 27 ft.*lbf }

    3. Engage the fastener to connect the rear No. 2 floor board sub-assembly.

  10. INSTALL REAR SEAT CUSHION LOCK HOOK


    1. A003YR7

      Engage the claw to install a new rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure the LH side and RH side.

  11. INSTALL REAR SEAT CUSHION ASSEMBLY


    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. A003XOT

      Pass the rear center seat outer belt assembly through the rear seat cushion assembly.

    3. Install the rear center seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    4. A003W09

      Engage the guide as shown in the illustration.

    5. Pass the rear seat inner with center belt assembly LH and rear seat inner belt assembly through the rear seat cushion assembly as shown in the illustration.

      A003Z3XE01
      Text in Illustration
      *1 Rear Seat Inner Belt Assembly *2 Rear Seat Inner with Center Belt Assembly LH
    6. A003YOA

      Engage the 2 hooks of the seat cushion to the vehicle body as shown in the illustration.

    7. Confirm that the seat cushion is firmly installed.

      Note

      When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

  12. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A003YK0E01
      Text in Illustration
      *a Alignment Mark (Purple)

      Align the alignment mark (purple) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  13. INSTALL REAR DOOR SCUFF PLATE LH


    1. Engage the 4 claws, 2 guides and 2 clips to install the rear door scuff plate LH.

  14. INSTALL REAR DECK TRIM COVER


    1. Engage the 4 clips to install the rear deck trim cover.

  15. INSTALL DECK TRIM SERVICE HOLE COVER


    1. A003YBSE01

      Engage the 2 guides (B).

    2. Engage the 2 claws and guide (A) to install the deck trim service hole cover.

  16. INSTALL REAR NO. 1 FLOOR BOARD


    1. Engage the 2 claws and 2 clips.

    2. Install the rear No. 1 floor board with the bolt.

  17. INSTALL REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    1. Engage the claw and 2 clips to install the rear No. 2 floor board sub-assembly.

  18. INSTALL REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    1. Engage the 2 claws and 2 clips to install the rear No. 1 floor board sub-assembly.

  19. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover assembly.

  20. INSTALL DECK FLOOR BOX LH (w/o Woofer)


    1. Engage the 6 guides.

    2. Install the deck floor box LH with the clip.

  21. INSTALL REAR NO. 4 FLOOR BOARD (w/o Woofer)


    1. Install the rear No. 4 floor board.

  22. INSTALL REAR NO. 4 FLOOR BOARD (w/ Woofer)


    1. Engage the 2 clips and 3 guides to install the rear No. 4 floor board.

  23. INSTALL DECK FLOOR BOX RH


    1. Engage the 6 guides.

    2. Install the deck floor box RH with the clip.

  24. INSTALL REAR NO. 3 FLOOR BOARD


    1. Install the rear No. 3 floor board.

  25. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  26. INSTALL REAR NO. 2 FLOOR BOARD


    1. Install the rear No. 2 floor board.