POWER MIRROR CONTROL SYSTEM (w/ Memory) Power Retractable Mirrors do not Operate with Power Retract Mirror Switch

SYSTEM DESCRIPTION

The main body ECU (multiplex network body ECU) receives the retractable outer mirror switch signal from the retractable outer mirror switch. The main body ECU then sends the mirror retract/return signal to each outer mirror control ECU assembly via CAN communication. Based on the signal, each outer mirror control ECU assembly retracts or returns the outer rear view mirror assembly.

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. CHECK CAN COMMUNICATION SYSTEM

   
   

   1. Use the intelligent tester to check if the CAN communication system is functioning normally Click here.

      OK
      CAN communication DTC is not output.

   
   

   NG

   GO TO CAN COMMUNICATION SYSTEM Click here

   OK

2. READ VALUE USING INTELLIGENT TESTER (RETRACTABLE OUTER MIRROR SWITCH)

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Enter the following menus: Body / Main Body / Data List.

   5. Read the Data List according to the display on the intelligent tester.

      Main Body

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      Outer Mirror Fold SW	Retractable outer mirror switch signal / ON or OFF	ON: Retractable outer mirror switch in retract position OFF: Retractable outer mirror switch in driving position	-

      OK
      On the intelligent tester screen, ON or OFF is displayed for each item according to the above.

   
   

   NG

   INSPECT RETRACTABLE OUTER MIRROR SWITCH Click here

   OK

3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MIRROR RETRACT FUNCTION)

   
   

   1. Enter the following menus: Body / Mirror L or Mirror R / Active Test.

   2. Perform the Active Test according to the display on the intelligent tester.

      Mirror L / Mirror R

      Tester Display	Test Part	Control Range	Diagnostic Note
      Mirror Fold/Return	Mirror retract operation	Fold / Return	operate with power switch on (IG) and the vehicle stopped. This test activates the Fold / Return. This operation can be confirmed by watching the mirror move in the desired direction.

      Result
      Result Proceed to Outer rear view mirror assemblies operate normally A Outer rear view mirror assembly RH does not operate normally B Outer rear view mirror assembly LH does not operate normally C

   
   

   B

   INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH Click here

   C

   INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH Click here

   A

   REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)
      *b	(A) Forward Position
      *c	(B)
      *d	(C) Driving Position
      *e	(D)
      *f	(E) Retracted Position

      Remove the outer rear view mirror assembly RH Click here.

   2. When checking each mirror position, set the mirror position by hand. Apply auxiliary battery voltage and check the mirror movement.

      Note

      
      

      • Disconnect and reconnect the auxiliary battery for each mirror position check.

      • The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

      OK

      Measurement Condition Mirror Position Specified Condition Auxiliary battery positive (+) → Terminal z7-3 (MR+) Auxiliary battery negative (-) → Terminal z7-11 (MR-) Forward position (A) Moves from (A) to retracted position (E) Auxiliary battery negative (-) → Terminal z7-3 (MR+) Auxiliary battery positive (+) → Terminal z7-11 (MR-) Forward position (A) Does not move Auxiliary battery positive (+) → Terminal z7-3 (MR+) Auxiliary battery negative (-) → Terminal z7-11 (MR-) Between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Auxiliary battery negative (-) → Terminal z7-3 (MR+) Auxiliary battery positive (+) → Terminal z7-11 (MR-) Between forward position (A) and driving position (C) Moves from (B) to forward position (A) Auxiliary battery positive (+) → Terminal z7-3 (MR+) Auxiliary battery negative (-) → Terminal z7-11 (MR-) Driving position (C) Moves from (C) to retracted position (E) Auxiliary battery negative (-) → Terminal z7-3 (MR+) Auxiliary battery positive (+) → Terminal z7-11 (MR-) Driving position (C) Does not move Auxiliary battery positive (+) → Terminal z7-3 (MR+) Auxiliary battery negative (-) → Terminal z7-11 (MR-) Between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Auxiliary battery negative (-) → Terminal z7-3 (MR+) Auxiliary battery positive (+) → Terminal z7-11 (MR-) Between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Auxiliary battery positive (+) → Terminal z7-3 (MR+) Auxiliary battery negative (-) → Terminal z7-11 (MR-) Retracted position (E) Does not move Auxiliary battery negative (-) → Terminal z7-3 (MR+) Auxiliary battery positive (+) → Terminal z7-11 (MR-) Retracted position (E) Moves from (E) to driving position (C)

   
   

   NG

   REPLACE OUTER MIRROR ACTUATOR ASSEMBLY RH Click here

   OK

   REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (RH SIDE) Click here

5. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)
      *b	(A) Forward Position
      *c	(B)
      *d	(C) Driving Position
      *e	(D)
      *f	(E) Retracted Position

      Remove the outer rear view mirror assembly LH Click here.

   2. When checking each mirror position, set the mirror position by hand. Apply auxiliary battery voltage and check the mirror movement.

      Note

      
      

      • Disconnect and reconnect the auxiliary battery for each mirror position check.

      • The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

      OK

      Measurement Condition Mirror Position Specified Condition Auxiliary battery positive (+) → Terminal z6-3 (MR+) Auxiliary battery negative (-) → Terminal z6-11 (MR-) Forward position (A) Moves from (A) to retracted position (E) Auxiliary battery negative (-) → Terminal z6-3 (MR+) Auxiliary battery positive (+) → Terminal z6-11 (MR-) Forward position (A) Does not move Auxiliary battery positive (+) → Terminal z6-3 (MR+) Auxiliary battery negative (-) → Terminal z6-11 (MR-) Between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Auxiliary battery negative (-) → Terminal z6-3 (MR+) Auxiliary battery positive (+) → Terminal z6-11 (MR-) Between forward position (A) and driving position (C) Moves from (B) to forward position (A) Auxiliary battery positive (+) → Terminal z6-3 (MR+) Auxiliary battery negative (-) → Terminal z6-11 (MR-) Driving position (C) Moves from (C) to retracted position (E) Auxiliary battery negative (-) → Terminal z6-3 (MR+) Auxiliary battery positive (+) → Terminal z6-11 (MR-) Driving position (C) Does not move Auxiliary battery positive (+) → Terminal z6-3 (MR+) Auxiliary battery negative (-) → Terminal z6-11 (MR-) Between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Auxiliary battery negative (-) → Terminal z6-3 (MR+) Auxiliary battery positive (+) → Terminal z6-11 (MR-) Between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Auxiliary battery positive (+) → Terminal z6-3 (MR+) Auxiliary battery negative (-) → Terminal z6-11 (MR-) Retracted position (E) Does not move Auxiliary battery negative (-) → Terminal z6-3 (MR+) Auxiliary battery positive (+) → Terminal z6-11 (MR-) Retracted position (E) Moves from (E) to driving position (C)

   
   

   NG

   REPLACE OUTER MIRROR ACTUATOR ASSEMBLY LH Click here

   OK

   REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (LH SIDE) Click here

6. INSPECT RETRACTABLE OUTER MIRROR SWITCH

   
   
   1. 

      Text in Illustration

      *a	Components without harness connected (Retractable Outer Mirror Switch)

      Remove the retractable outer mirror switch Click here.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition H137-2 (MR) - H137-3 (E) Retract position Below 1 Ω H137-2 (MR) - H137-3 (E) AUTO position 10 kΩ or higher H137-2 (MR) - H137-3 (E) Return position 10 kΩ or higher

   
   

   NG

   REPLACE RETRACTABLE OUTER MIRROR SWITCH Click here

   OK

7. CHECK HARNESS AND CONNECTOR (RETRACTABLE OUTER MIRROR SWITCH - MAIN BODY ECU)

   
   

   1. Disconnect the H17 connector.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition H137-2 (MR) - H17-28 (RET) Always Below 1 Ω H137-2 (MR) - Body ground Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR (RETRACTABLE OUTER MIRROR SWITCH - MAIN BODY ECU)

   OK

   REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here