Click here

BACK DOOR ADJUSTMENT

Click here
Click here
Table 1. Text in Illustration *1 Centering Bolt *2 Standard Bolt
Tip:

  • Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.

  • Specified torque for standard bolts is shown in the standard bolt chart (Click here).

Click here
  1. Click here

    INSPECT BACK DOOR


    1. A003XANE01

      Check that the clearance measurements of areas *a through *l are within each standard range.

      Table 2. Standard Clearance
      Area Measurement Area Measurement
      *a 5.2 to 8.2 mm (0.205 to 0.323 in.) *b 0 to 3.0 mm (0 to 0.118 in.)
      *c 5.2 to 8.2 mm (0.205 to 0.323 in.) *d 4.0 to 7.0 mm (0.157 to 0.276 in.)
      *e 1.2 to 4.2 mm (0.0472 to 0.165 in.) *f 4.0 to 7.0 mm (0.157 to 0.276 in.)
      *g 1.1 to 4.7 mm (0.0433 to 0.185 in.) *h 3.25 to 7.25 mm (0.128 to 0.285 in.)
      *i -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) *j 3.2 to 7.2 mm (0.126 to 0.283 in.)
      *k -1.8 to 2.2 mm (-0.0709 to 0.0866 in.) *l 3.85 to 5.85 mm (0.152 to 0.230 in.)
  2. Click here

    REMOVE REAR NO. 2 FLOOR BOARD


    1. Remove the rear No. 2 floor board.

  3. Click here

    REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  4. Click here

    REMOVE REAR NO. 3 FLOOR BOARD


    1. Remove the rear No. 3 floor board.

  5. Click here

    REMOVE DECK FLOOR BOX RH


    1. A003Z5J

      Remove the clip.

    2. Disengage the 6 guides and remove the deck floor box RH.

  6. Click here

    REMOVE REAR NO. 4 FLOOR BOARD (w/o Woofer)


    1. Remove the rear No. 4 floor board.

  7. Click here

    REMOVE REAR NO. 4 FLOOR BOARD (w/ Woofer)


    1. A003WPK

      Disengage the 2 clips and 3 guides, and remove the rear No. 4 floor board.

  8. Click here

    REMOVE DECK FLOOR BOX LH (w/o Woofer)


    1. A003WLJ

      Remove the clip.

    2. Disengage the 6 guides and remove the deck floor box LH.

  9. Click here

    REMOVE DECK TRIM SERVICE HOLE COVER


    1. A003YBSE01

      Disengage the 2 claws and guide (A).

    2. Disengage the 2 guides (B) and remove the deck trim service hole cover.

  10. Click here

    REMOVE REAR DECK TRIM COVER


    1. A003YUE

      Disengage the 4 clips and remove the rear deck trim cover.

  11. Click here

    ADJUST BACK DOOR


    1. A003ZE4

      Before adjusting the upper end of the back door up and down or left and right, loosen the bolts.

    2. Tighten the body side hinge after the adjustment.

      19 N*m 194 kgf*cm 14 ft.*lbf
    3. A003WCE

      Loosen the 3 bolts.

    4. Tighten the bolts after the adjustment.

      7.5 N*m 76 kgf*cm 66 in.*lbf
  12. Click here

    INSTALL REAR DECK TRIM COVER


    1. Engage the 4 clips to install the rear deck trim cover.

  13. Click here

    INSTALL DECK TRIM SERVICE HOLE COVER


    1. A003YBSE01

      Engage the 2 guides (B).

    2. Engage the 2 claws and guide (A) to install the deck trim service hole cover.

  14. Click here

    INSTALL DECK FLOOR BOX LH (w/o Woofer)


    1. Engage the 6 guides.

    2. Install the deck floor box LH with the clip.

  15. Click here

    INSTALL REAR NO. 4 FLOOR BOARD (w/o Woofer)


    1. Install the rear No. 4 floor board.

  16. Click here

    INSTALL REAR NO. 4 FLOOR BOARD (w/ Woofer)


    1. Engage the 2 clips and 3 guides to install the rear No. 4 floor board.

  17. Click here

    INSTALL DECK FLOOR BOX RH


    1. Engage the 6 guides.

    2. Install the deck floor box RH with the clip.

  18. Click here

    INSTALL REAR NO. 3 FLOOR BOARD


    1. Install the rear No. 3 floor board.

  19. Click here

    INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  20. Click here

    INSTALL REAR NO. 2 FLOOR BOARD


    1. Install the rear No. 2 floor board.