HOOD LOCK CONTROL CABLE ASSEMBLY REMOVAL


  1. REMOVE FRONT BUMPER ASSEMBLY

    Click here

  2. REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)


    1. A003YXS

      Disconnect the connector.

    2. A003XDO

      Remove the 3 bolts and the millimeter wave radar sensor assembly.

  3. REMOVE FRONT WHEEL LH (for LHD)

  4. REMOVE FRONT FENDER LINER LH (for LHD)

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  5. REMOVE FRONT WHEEL RH (for RHD)

  6. REMOVE FRONT FENDER LINER RH (for RHD)


    1. A003XBFE01

      Using a screwdriver, turn each pin 90 degrees counterclockwise and remove the 2 pin hold clips.

    2. A003VN9

      Using a 4 mm hexagon wrench, remove the 3 screws.

    3. A003WD4E01

      Remove the 6 screws and bolt.

    4. Remove the 6 clips and 2 grommets and front fender liner RH.

      Tech Tips

      The grommets need to be replaced with new ones because they will break when they are removed.

      Text in Illustration
      *1 Grommet

  7. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)


    1. A003VX8

      Disengage the 4 claws, 2 guides and 4 clips, and remove the front door scuff plate LH.

  8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD)


    1. A003X2U

      Remove the clip as shown in the illustration.

    2. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.

  9. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. A003Y9D

      Remove the 2 screws <E>.

    2. Disengage the clip.

    3. Disengage the clamp.

    4. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  10. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  11. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH (for RHD)

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  12. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. A003ZMA

      Remove the screw <E>.

    2. Disengage the 2 clips.

    3. Disengage the clamp.

    4. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  13. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A003VHK

      Disengage the claw and 2 guides, and disconnect the hood lock control lever sub-assembly.

  14. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A003XSO

      Disconnect the hood lock control cable assembly and remove the hood lock control lever sub-assembly.

  15. REMOVE HOOD LOCK ASSEMBLY (w/o Engine Hood Courtesy Switch)


    1. A003W68E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the hood lock nut cap.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A003VTAE01
      Text in Illustration
      *1 Hood Lock Bolt

      Remove the 2 bolts and hood lock bolt.

    3. for LHD:


      1. A003X78

        Disconnect the hood lock control cable and remove the hood lock assembly.

    4. For RHD:


      1. A003W92

        Disconnect the hood lock control cable and remove the hood lock assembly.

  16. REMOVE HOOD LOCK ASSEMBLY (w/ Engine Hood Courtesy Switch)


    1. A003VZDE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the hood lock nut cap.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A003V1OE01
      Text in Illustration
      *1 Hood Lock Bolt

      Disconnect the connector.

    3. Disengage the clamp.

    4. Remove the 2 bolts and hood lock bolt.

    5. for LHD:


      1. A003X4C

        Disconnect the hood lock control cable and remove the hood lock assembly.

    6. For RHD:


      1. A003X9K

        Disconnect the hood lock control cable and remove the hood lock assembly.

  17. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)


    1. Using a screwdriver, disengage each clamp shown in the illustration.

      A003WEIE01
      Text in Illustration
      *1 Hood Lock Control Cable *2 Grommet
      *3 Hood Cable Grommet - -

      Tech Tips

      Tape the screwdriver tip before use.

    2. Pull the hood lock control cable assembly from the engine compartment and remove it.

  18. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)


    1. Using a screwdriver, disengage each clamp shown in the illustration.

      A003YOLE01
      Text in Illustration
      *1 Hood Lock Control Cable *2 Grommet
      *3 Hood Cable Grommet - -

      Tech Tips

      Tape the screwdriver tip before use.

    2. Pull the hood lock control cable assembly from the engine compartment and remove it.