Click here

WINDSHIELD GLASS REMOVAL

Click here
Click here
  1. Click here

    REMOVE FRONT WIPER ARM HEAD CAP


    1. A003YRSE01

      Using a screwdriver, disengage the 3 claws and remove the front wiper arm head cap.

      Table 1. Text in Illustration
      *1 Protective Tape
      Tip:

      • Tape the screwdriver tip before use.

      • Use the same procedure for the RH side and LH side.

  2. Click here

    REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. A003ZKK

      Remove the nut and the front wiper arm and blade assembly LH.

  3. Click here

    REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. A003VE4

      Remove the nut and the front wiper arm and blade assembly RH.

  4. Click here

    REMOVE FRONT NO. 2 SIDE PANEL PROTECTOR LH


    1. A003XZCE01

      Disengage the clip and guide, and remove the front No. 2 side panel protector LH.

      Table 2. Text in Illustration
      *1 Double-sided Tape
  5. Click here

    REMOVE FRONT NO. 2 SIDE PANEL PROTECTOR RH

    Tip:

    Use the same procedure as for the LH side.

  6. Click here

    REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. A003ZOG

      Remove the 2 clips.

    2. A003Y5F

      Disengage the 6 claws and guide as shown in the illustration.

    3. A003X59

      Disengage the 7 guides and pull out the cowl top ventilator louver sub-assembly as shown in the illustration.

  7. Click here

    REMOVE WINDSHIELD OUTSIDE MOULDING LH


    1. A003ZM7E01

      Put protective tape around the windshield outside moulding.

      Table 3. Text in Illustration
      *1 Protective Tape
    2. A003YNB

      Using a moulding remover, disengage the 10 claws.

    3. Disengage the guide and remove the windshield outside moulding.

  8. Click here

    REMOVE WINDSHIELD OUTSIDE MOULDING RH

    Tip:

    Use the same procedure as for the LH side.

  9. Click here

    REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. w/o Rear View Monitor System:


      1. A003W36

        Disengage the 2 guides and slide the inner rear view mirror stay holder cover as shown in the illustration.

      2. A003ZM5

        Disengage the 6 claws and remove the inner rear view mirror stay holder cover.

    2. w/ Rear View Monitor System:


      1. A003YB5

        Disengage the 2 guides and slide the inner rear view mirror stay holder cover as shown in the illustration.

      2. A003WC6

        Disengage the 2 claws and remove the inner rear view mirror stay holder cover.

  10. Click here

    REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)


    1. A003W5A

      Disengage the 2 claws and disconnect the inner mirror base cover.

    2. A003VXRE01

      Pull the lever in the direction indicated by the arrow in the illustration, and slide the inner rear view mirror assembly upward to remove it.

  11. Click here

    REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)


    1. A003WM7E01

      Disconnect the connector.

      Table 4. Text in Illustration
      *A w/o Rear View Monitor System
      *B w/ Rear View Monitor System

    2. Using a T20 "TORX" socket wrench, remove the screw and inner rear view mirror assembly.

  12. Click here

    REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    1. A003X8A

      Disengage the 2 guides and disconnect the rain sensor cover as shown in the illustration.

    2. Disengage the 2 claws and remove the rain sensor cover.

  13. Click here

    REMOVE RAIN SENSOR (w/ Rain Sensor)


    1. A003ZQC

      Disconnect the connector.

    2. A003XTJE01

      Release the stopper by pulling the stopper down and disconnect the rain sensor as shown in the illustration.

      Table 5. Text in Illustration
      *1 Stopper
  14. Click here

    REMOVE PROTECTOR (w/ Humidity Sensor)


    1. A003W59

      Disengage the 2 guides and slide the protector as shown in the illustration.

    2. Disengage the 2 claws and remove the protector.

  15. Click here

    REMOVE HUMIDITY SENSOR (w/ Humidity Sensor)


    1. A003Z4B

      Disconnect the connector.

    2. A003Z18E01

      Release the stopper by pulling it down.

      Table 6. Text in Illustration
      *1 Stopper

    3. Remove the humidity sensor as shown in the illustration.

  16. Click here

    DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A003YSW

      Disconnect the front door opening trim weatherstrip.

    2. Remove the residual weatherstrip sealant from the body of the vehicle using cleaner.

      Note:

      Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.

  17. Click here

    REMOVE FRONT PILLAR GARNISH LH


    1. A003WN2E01

      Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

      Table 7. Text in Illustration
      *1 Front Pillar Garnish Clip
      Tip:

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    2. A003X1NE01

      Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.

      Table 8. Text in Illustration
      *1 Protective Tape
      Note:

      • Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.

      • Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

      Tip:

      Tape the tips of the needle-nosed pliers before use.

    3. Disengage the 2 guides.

    4. w/o Front Center Speaker:


      1. Remove the front pillar garnish LH by pulling it in the direction indicated by the arrow (2) in the illustration.

    5. w/ Front Center Speaker:


      1. Disconnect the front pillar garnish LH by pulling it in the direction indicated by the arrow (2) in the illustration.

      2. Disconnect the connector and remove the front pillar garnish LH.

    6. A003YYHE01

      Protect the curtain shield airbag assembly.

      Table 9. Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      1. Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.

        Note:

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  18. Click here

    DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tip:

    Use the same procedure as for the LH side.

  19. Click here

    REMOVE FRONT PILLAR GARNISH RH

    Tip:

    Use the same procedure as for the LH side.

  20. Click here

    REMOVE MAP LIGHT ASSEMBLY


    1. Open the overhead console.

    2. A003VMOE01

      Disengage the 4 clips and 3 guides as shown in the illustration.

    3. Disconnect the connector and remove the map light assembly.

  21. Click here

    REMOVE NO. 1 ROOM LIGHT ASSEMBLY


    1. A003WETE02

      Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws and remove the No. 1 room light lens.

      Table 10. Text in Illustration
      *1 Protective Tape
    2. A003WKME02

      Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws and disconnect the No. 1 room light housing as shown in the illustration.

      Table 11. Text in Illustration
      *1 Protective Tape
    3. A003ZFHE01

      Disengage the 4 claws and disconnect the room light switch base from the No. 1 room light housing.

      Table 12. Text in Illustration
      *a Room Light Switch Base
  22. Click here

    REMOVE ASSIST GRIP SUB-ASSEMBLY


    1. A003YT9E01

      Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.

      Table 13. Text in Illustration
      *1 Protective Tape
      Note:

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tip:

      Tape the screwdriver tip before use.

    2. Disengage the 2 clips and remove the assist grip sub-assembly.

    3. A003VS0

      Remove the 2 clips from the vehicle body.

      Tip:

      Use the same procedure for the other 3 assist grip sub-assemblies.

  23. Click here

    REMOVE VISOR BRACKET COVER (for LH Side)


    1. A003ZAT

      Using a moulding remover, disengage the 4 claws and remove the visor bracket cover LH.

  24. Click here

    REMOVE VISOR ASSEMBLY LH


    1. A003WM1

      Remove the 2 screws and the visor assembly LH.

  25. Click here

    REMOVE VISOR BRACKET COVER (for RH Side)

    Tip:

    Use the same procedure as for the LH side.

  26. Click here

    REMOVE VISOR ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

  27. Click here

    REMOVE VISOR HOLDER


    1. A003XURE01

      Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Disengage the 2 claws and remove the visor holder.

      Tip:

      Use the same procedure for the other visor holder.

  28. Click here

    REMOVE SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)


    1. Remove the sliding roof opening trim moulding.

  29. Click here

    REMOVE ROOF HEADLINING ASSEMBLY


    1. Slightly lower the front section of the roof headlining assembly so that the windshield glass can be removed.

      Tip:

      It is not necessary to completely remove the roof headlining assembly.

  30. Click here

    REMOVE WINDSHIELD GLASS SUB-ASSEMBLY


    1. w/ Front Window Deicer System:


      1. A003W8DE01

        Disengage the 3 clamps.

        Table 14. Text in Illustration
        *A LHD
        *B RHD

      2. Disconnect the connector.

    2. A003VLNE01

      Apply protective tape to the area around the installation position of the windshield glass on the vehicle body to prevent it from being scratched.

      Table 15. Text in Illustration
      *1 Protective Tape
    3. A003YHKE01

      Pass a piano wire between the vehicle body and glass from the interior, as shown in the illustration.

      Table 16. Text in Illustration
      *1 Wooden Block
      *2 Plastic Sheet
      *3 Stopper
      *4 Piano Wire

    4. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

    5. Cut off the adhesive by pulling the piano wire around the windshield glass sub-assembly.

      Note:

      • When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.

      • To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.

    6. A003YC8E01

      Place matchmarks on the windshield glass sub-assembly and vehicle body on the locations indicated in the illustration.

      Table 17. Text in Illustration
      *1 Matchmark
      Tip:

      Matchmarks are not necessary if the windshield glass sub-assembly is not going to be reused.

    7. A003V4AE01

      Disconnect the windshield glass stoppers.

      Table 18. Text in Illustration
      *A 1-piece Type *B 2-pieceType
      *1 No. 1 Stopper *2 No. 2 Stopper
      Note:

      • There are No. 1 and No. 2 stoppers on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.

      • To prevent the windshield glass from falling when performing this operation, be sure to hold the windshield glass using suction cups.

      Tip:

      Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.

    8. Using suction cups, remove the windshield glass sub-assembly.

      Note:

      • Be careful not to drop the windshield glass sub-assembly.

      • Leave as much adhesive on the vehicle body as possible when removing the windshield glass sub-assembly.

  31. Click here

    REMOVE WINDSHIELD GLASS ADHESIVE DAM


    1. When reusing the windshield glass sub-assembly:


      1. A003V1TE01

        Using a scraper, remove the windshield glass adhesive dam.

        Table 19. Text in Illustration
        *A Back Side
        Note:

        • Be careful not to damage the windshield glass.

        • Be sure to replace the window glass adhesive dam with a new one.

  32. Click here

    REMOVE WINDSHIELD OUTSIDE MOULDING


    1. When reusing the windshield glass sub-assembly:


      1. A003XDIE01

        Using a scraper, remove the windshield outside moulding.

        Table 20. Text in Illustration
        *A Back Side
        Note:

        • Be careful not to damage the windshield glass.

        • Be sure to replace the windshield outside moulding with a new one.

  33. Click here

    REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)


    1. When reusing the windshield glass sub-assembly:


      1. A003WY1E01

        Using a scraper, remove the 2 No. 1 windshield glass stoppers.

        Table 21. Text in Illustration
        *A Back Side
        Note:

        • Be careful not to damage the windshield glass.

        • Be sure to replace the 1-piece type No. 1 windshield glass stoppers with a new pair of 2-piece type No. 1 and No. 2 windshield glass stoppers.

  34. Click here

    REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)


    1. When reusing the windshield glass sub-assembly:


      1. A003VR2E01

        Using a scraper, remove the 2 No. 2 windshield glass stoppers.

        Table 22. Text in Illustration
        *A Back Side
        Note:

        • Be careful not to damage the windshield glass.

        • Be sure to replace the No. 2 windshield glass stoppers with new ones.

  35. Click here

    REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)


    1. A003XZP

      Remove the 2 No. 1 windshield glass stoppers.

      Note:

      Be sure to replace the No. 1 windshield glass stoppers with new ones.

  36. Click here

    CLEAN WINDSHIELD GLASS


    1. When reusing the windshield glass:


      1. A003ZKQ

        Using a scraper, remove any adhesive tape and adhesive residue from the windshield glass.

        Note:

        Be careful not to damage the windshield glass.

      2. Clean the outer circumference of the windshield glass with a non-residue solvent.

        Note:

        • Do not touch the windshield glass surface after cleaning it.

        • Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.

  37. Click here

    CLEAN VEHICLE BODY


    1. A003ZJ1E07

      Clean and shape the contact surfaces of the vehicle body.

      Table 23. Text in Illustration
      *1 Adhesive
      *2 Body

      1. Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body as shown in the illustration.

        Note:

        Be careful not to damage the vehicle body.

        Tip:

        Leave as much adhesive on the vehicle body as possible.

      2. Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

        Tip:

        Even if all the adhesive has been removed, clean the vehicle body.