POWER WINDOW REGULATOR MOTOR (for Front Door) REMOVAL

REMOVE REAR NO. 2 FLOOR BOARD

1. Remove the rear No. 2 floor board.

REMOVE REAR DECK FLOOR BOX

1. Remove the rear deck floor box.

REMOVE REAR NO. 3 FLOOR BOARD

1. Remove the rear No. 3 floor board.

REMOVE DECK FLOOR BOX RH

1. 

   Remove the clip.

2. Disengage the 6 guides and remove the deck floor box RH.

REMOVE REAR FLOOR BOARD UPPER NO. 3 PLATE

1. 

   Disengage the 4 claws and 2 guides, and remove the rear floor board upper No. 3 plate.

REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

1. 

   Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.

REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

1. 

   Disengage the clip and claw, and remove the front door lower frame bracket garnish.

REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

1. 

   Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides as shown in the illustration.

2. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.

REMOVE DOOR ARMREST COVER (for Driver Side)

1. 

   Remove the door armrest cover.

REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for Driver Side)

1. 

   Put protective tape around the front door panel.

   Table 1. Text in Illustration

   *1	Protective Tape

2. 

   Remove the 3 screws.

3. Using a clip remover, disengage the 11 clips.

4. Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

5. Raise the front door trim board sub-assembly and remove it.

6. w/ Seat Position Memory System:

   
   

   1. Disconnect the connector.

7. 

   Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.

REMOVE DOOR ASSIST GRIP COVER (for Front Passenger Side)

1. 

   Using a moulding remover, disengage the 4 claws and guide to remove the door assist grip cover.

REMOVE DOOR ASSIST GRIP ASSEMBLY (for Front Passenger Side)

1. 

   Remove the 2 screws.

2. Disengage the 3 guides and remove the door assist grip assembly.

REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

1. 

   Using a moulding remover, disengage the 3 clips, 8 claws and 4 guides as shown in the illustration.

2. Disconnect each connector and remove the power window regulator switch assembly with front door armrest base panel.

REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for Front Passenger Side)

1. 

   Put protective tape around the front door panel.

   Table 2. Text in Illustration

   *1	Protective Tape

2. 

   Remove the 2 screws.

3. Using a clip remover, disengage the 11 clips.

4. Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

5. Raise the front door trim board sub-assembly and remove the front door trim board sub-assembly .

6. 

   Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.

REMOVE FRONT DOOR TRIM BRACKET (for Driver Side)

1. 

   Remove the 2 screws and front door trim bracket.

REMOVE FRONT DOOR TRIM BRACKET (for Front Passenger Side)

1. 

   Remove the 2 screws and front door trim bracket.

REMOVE FRONT DOOR SERVICE HOLE COVER

1. 

   Remove the front door service hole cover.

   Tip:

   Remove any remaining butyl tape from the door.

REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

1. 

   Remove the grommet.

2. Connect the cable to the negative (-) battery terminal.

3. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

4. Disconnect the cable from the negative (-) battery terminal.

   Note:

   When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

5. Disconnect the power window regulator master switch assembly.

6. 

   Remove the 2 bolts.

   Note:

   After the bolts are removed, do not allow the door glass to fall.

7. 

   Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

   Note:

   Do not damage the door glass.

REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

1. 

   Disconnect the connector.

2. Loosen the temporary bolt.

   Table 3. Text in Illustration

   *1	Temporary Bolt

   Note:

   Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

3. Remove the 5 bolts.

4. Remove the front door window regulator assembly.

5. Remove the temporary bolt from the front door window regulator assembly.