ROOF HEADLINING INSTALLATION

INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
1. Put the roof headlining assembly into the vehicle through the back door.
  
  Note
  
  Do not damage the roof headlining assembly or body interior.
2. Install the 3 clips.
3. Engage the 3 clamps and connect the 2 connectors to the front pillar LH.
4. w/o G-BOOK System:
  1. Engage the 3 clamps and connect the connector to the front pillar RH.
  2. Connect the connector to the rear pillar RH.
5. w/ G-BOOK System:
  1. Engage the 3 clamps and connect the 2 connectors to the front pillar RH.
  2. Connect the 2 connectors to the rear pillar RH.
6. w/ EC Mirror
  1. Connect the inner rear view mirror connector.
7. w/ Humidity Sensor
  1. Connect the humidity sensor connector.
8. w/ Rain Sensor
  1. Connect the rain sensor connector
INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
1. Put the roof headlining assembly into the vehicle through the back door.
  
  Note
  
  Do not damage the roof headlining assembly or body interior.
2. Install the 3 clips.
3. Connect the connector to the sliding roof drive gear assembly.
4. Engage the 3 clamps and connect the 2 connectors to the front pillar LH.
5. w/o G-BOOK System:
  1. Engage the 3 clamps and connect the connector to the front pillar RH.
  2. Connect the connector to the rear pillar RH.
6. w/ G-BOOK System:
  1. Engage the 3 clamps and connect the 2 connectors to the front pillar RH.
  2. Connect the 2 connectors to the rear pillar RH.
7. w/ EC Mirror
  1. Connect the inner rear view mirror connector.
8. w/ Humidity Sensor
  1. Connect the humidity sensor connector.
9. w/ Rain Sensor
  1. Connect the rain sensor connector
INSTALL VISOR HOLDER
1. Engage the 2 claws.
2. Push in the visor holder as shown in the illustration.
  
  Tech Tips
  
  Use the same procedure for the other visor holder.
INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)
1. Text in Illustration
  
  *a Notch
  
  *b Alignment Mark (Green)
  
  Align the alignment mark (green) on the moulding with the notch of the roof headlining to install the sliding roof opening trim moulding.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL VISOR ASSEMBLY LH
1. Install the visor assembly LH with the 2 screws.
INSTALL VISOR BRACKET COVER (for LH Side)
1. Engage the 4 claws to install the visor bracket cover LH.
INSTALL VISOR ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL VISOR BRACKET COVER (for RH Side)

Tech Tips

Use the same procedure as for the LH side.
INSTALL ASSIST GRIP SUB-ASSEMBLY
1. Assemble the assist grip sub-assembly as shown in the illustration.
2. Install the assist grip sub-assembly.
  
  Tech Tips
  
  Use the same procedure for the other 3 assist grip sub-assemblies.
INSTALL PROTECTOR (w/ Humidity Sensor)
1. Engage the 2 claws and temporarily install the protector.
2. Slide the protector and engage the 2 guides as shown in the illustration to install the protector.
INSTALL RAIN SENSOR COVER (w/ Rain Sensor)
1. Engage the 2 claws and connect the rain sensor cover.
2. Engage the 2 guides and install the rain sensor cover as shown in the illustration.
INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)
1. w/o Rear View Monitor System:
  1. Engage the 6 claws to install the inner rear view mirror stay holder cover.
  2. Engage the 2 guides to install the inner rear view mirror stay holder cover as shown in the illustration.
2. w/ Rear View Monitor System:
  1. Engage the 2 claws to install the inner rear view mirror stay holder cover.
  2. Engage the 2 guides to install the inner rear view mirror stay holder cover as shown in the illustration.

Text in Illustration
*a	Notch
*b	Alignment Mark (Green)

INSTALL NO. 1 ROOM LIGHT ASSEMBLY

Text in Illustration
*a	Switch Part of Room Light Switch Base
*b	Switch Part of No. 1 Room Light Housing

Align the switch parts shown in the illustration and engage the 4 claws to install the room light switch base to the No. 1 room light housing.

Engage the 4 claws to install the No. 1 room light housing.
Engage the 4 claws to install the No. 1 room light lens.

INSTALL MAP LIGHT ASSEMBLY
1. Connect the connector.
2. Engage the 3 guides and 4 clips to install the map light assembly as shown in the illustration.
3. Close the overhead console.

INSTALL BACK DOOR WEATHERSTRIP

Text in Illustration
*a	Joint
*b	Alignment mark (Blue)
*c	Alignment mark (Pink)

Install a new back door weatherstrip so that the alignment marks, joint and sections indicated by the arrows, are aligned as shown in the illustration.

Note

After installation, check that the corners fit correctly.

INSTALL UPPER INSTRUMENT PANEL ASSEMBLY

Click here
INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH
1. Pass the floor anchor of the rear seat outer belt assembly LH through the roof side inner garnish LH.
2. Engage the 8 clips to install the roof side inner garnish assembly LH.
3. Engage the 2 guides.
4. Engage the 3 claws to connect the belt guide.
INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
1. Engage the 4 claws and 3 clips.
2. Install the deck trim side panel assembly LH with the 3 screw.
CONNECT REAR SEAT OUTER BELT ASSEMBLY LH
1. Text in Illustration
  
  *1 Protruding Part
  
  Connect the floor end of the rear seat outer belt assembly with the bolt.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
  
  Note
  
  Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.
INSTALL TONNEAU COVER HOLDER CAP (for LH Side)
1. Engage the guide.
2. Engage the claw to install the tonneau cover holder cap.
INSTALL TONNEAU COVER HOOK (for LH Side)
1. Engage the 2 claws and pin to install the tonneau cover hook.
INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)
1. Engage the guide.
2. Install the luggage hold belt striker assembly with the bolt.
INSTALL ROPE HOOK ASSEMBLY (for LH Side)
1. Install the rope hook assembly with the bolt.
2. Engage the 2 claws.
INSTALL REAR SEAT SIDE GARNISH LH
1. Engage the 6 claws.
2. Install the rear seat side garnish LH with the clip.
INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL REAR SEAT OUTER BELT ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL NO. 2 ROOM LIGHT ASSEMBLY
1. Connect the connector.
2. Engage the claw to install the No. 2 room light assembly.
INSTALL TONNEAU COVER HOLDER CAP (for RH Side)

Tech Tips

Use the same procedure as for the LH side.
INSTALL TONNEAU COVER HOOK (for RH Side)
1. Engage the 2 claws and pin to install the tonneau cover hook.
INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

Tech Tips

Use the same procedure as for the LH side.
INSTALL ROPE HOOK ASSEMBLY (for RH Side)

Tech Tips

Use the same procedure as for the LH side.
INSTALL REAR SEAT SIDE GARNISH RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL REAR SEAT SIDE COVER RH
1. Engage the 3 claws and 2 clips to install the rear seat side cover RH.
INSTALL CENTER PILLAR UPPER GARNISH LH
1. Pass the floor anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH.
2. Engage the 2 clips.
3. Install the center pillar upper garnish LH with the screw.
INSTALL CENTER PILLAR LOWER GARNISH LH
1. Engage the 4 claws and 2 clips to install the center pillar lower garnish LH.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
1. Install the floor end of the front seat outer belt assembly with the bolt.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
2. Check if the ELR locks.
  
  Note
  
  The check should be performed with the outer belt assembly installed.
  1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)
1. Engage the 3 claws to install the lap belt outer anchor cover.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
1. Text in Illustration
  
  *a Alignment Mark (Purple)
  
  Align the alignment mark (purple) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL REAR DOOR SCUFF PLATE LH
1. Engage the 4 claws, 2 guides and 2 clips to install the rear door scuff plate LH.

Text in Illustration
*1	Protruding Part

Text in Illustration
*a	Alignment Mark (Purple)

INSTALL FRONT PILLAR GARNISH LH

Remove the protective cover.

Text in Illustration
*1	Front Pillar Garnish Clip
*2	Protective Tape

Make sure that the front pillar garnish clip is not damaged.

Note

If there is any damage, replace the garnish clip with a new one.
When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

Engage the 2 guides by moving the garnish in the direction indicated by the arrow (1).
Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.

Tech Tips

Tape the tips of the needle-nosed pliers before use.
Engage the 2 clips to install the front pillar garnish LH.

INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
1. Text in Illustration
  
  *a Alignment Mark (Orange)
  
  Align the alignment mark (orange) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
1. Engage the claw and clip.
  Note
  - Be sure to engage the clip securely.
  - If there is any damage, replace the garnish clip with a new one.
2. Install the cowl side trim sub-assembly LH with the clip.
INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
1. Connect the connector.
2. Engage the clamp.
3. Engage the 2 guides, claw and 2 clips to install the No. 2 instrument panel under cover sub-assembly.
INSTALL FRONT DOOR SCUFF PLATE LH
1. Engage the 4 claws, 2 guides and 4 clips to install the front door scuff plate LH.
INSTALL CENTER PILLAR UPPER GARNISH RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL CENTER PILLAR LOWER GARNISH RH

Tech Tips

Use the same procedure as for the LH side.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

Tech Tips

Use the same procedure as for the LH side.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
1. Text in Illustration
  
  *a Alignment Mark (Yellow green)
  
  Align the alignment mark (yellow green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL REAR DOOR SCUFF PLATE RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL FRONT PILLAR GARNISH RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
1. Text in Illustration
  
  *a Alignment Mark (Light blue)
  
  Align the alignment mark (light blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.

CAUTION:
for RHD models:
Make sure that the cowl side trim sub-assembly RH is securely installed. if the cowl side trim sub-assembly RH is not installed correctly, there is a possibility that it may interfere with the accelerator pedal.
INSTALL FRONT DOOR SCUFF PLATE RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL FRONT SEAT ASSEMBLY

for Manual Seat Click here

for power Seat Click here

Tech Tips

Use the same procedure for the RH side and LH side.
INSTALL REAR DECK TRIM COVER
1. Engage the 4 clips to install the rear deck trim cover.
INSTALL DECK TRIM SERVICE HOLE COVER
1. Engage the 2 guides (B).
2. Engage the 2 claws and guide (A) to install the deck trim service hole cover.
INSTALL REAR NO. 1 FLOOR BOARD
1. Engage the 2 claws and 2 clips.
2. Install the rear No. 1 floor board with the bolt.
INSTALL REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY
1. Engage the claw and 2 clips to install the rear No. 2 floor board sub-assembly.
INSTALL REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY
1. Engage the 2 claws and 2 clips to install the rear No. 1 floor board sub-assembly.
INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
1. Install the tonneau cover assembly.
INSTALL DECK FLOOR BOX LH (w/o Woofer)
1. Engage the 6 guides.
2. Install the deck floor box LH with the clip.
INSTALL REAR NO. 4 FLOOR BOARD (w/o Woofer)
1. Install the rear No. 4 floor board.
INSTALL REAR NO. 4 FLOOR BOARD (w/ Woofer)
1. Engage the 2 clips and 3 guides to install the rear No. 4 floor board.
INSTALL REAR SEATBACK ASSEMBLY RH
1. Place the rear seatback assembly RH in the cabin.
  
  Note
  
  Be careful not to damage the vehicle body.
2. Install the rear seatback assembly RH with the 2 bolts.
  
  Torque:
  
  37 N*m { 375 kgf*cm, 27 ft.*lbf }
3. Engage the fastener to connect the rear No. 1 floor board sub-assembly.
INSTALL REAR SEATBACK ASSEMBLY LH
1. Place the rear seatback assembly LH in the cabin.
  
  Note
  
  Be careful not to damage the vehicle body.
2. Install the rear seatback assembly LH with the 2 bolts.
  
  Torque:
  
  37 N*m { 375 kgf*cm, 27 ft.*lbf }
3. Engage the fastener to connect the rear No. 2 floor board sub-assembly.
INSTALL REAR SEAT CUSHION LOCK HOOK
1. Engage the claw to install a new rear seat cushion lock hook.
  
  Note
  
  Rear seat cushion lock hooks must not be reused.
  
  Tech Tips
  
  Use the same procedure the LH side and RH side.

Text in Illustration
*a	Alignment Mark (Orange)

Text in Illustration
*a	Alignment Mark (Yellow green)

Text in Illustration
*a	Alignment Mark (Light blue)

INSTALL REAR SEAT CUSHION ASSEMBLY

Place the rear seat cushion assembly in the cabin.

Note

Be careful not to damage the vehicle body.
Pass the rear center seat outer belt assembly through the rear seat cushion assembly.
Install the rear center seat outer belt assembly with the bolt.

Torque:

42 N*m { 428 kgf*cm, 31 ft.*lbf }
Engage the guide as shown in the illustration.

Pass the rear seat inner with center belt assembly LH and rear seat inner belt assembly through the rear seat cushion assembly as shown in the illustration.

Text in Illustration
*1	Rear Seat Inner Belt Assembly	*2	Rear Seat Inner with Center Belt Assembly LH

Engage the 2 hooks of the seat cushion to the vehicle body as shown in the illustration.
Confirm that the seat cushion is firmly installed.

Note

When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

INSTALL REAR FLOOR BOARD UPPER NO. 3 PLATE
1. Engage the 4 claws and 2 guides to install the rear floor board upper No. 3 plate.
INSTALL DECK FLOOR BOX RH
1. Engage the 6 guides.
2. Install the deck floor box RH with the clip.
INSTALL REAR NO. 3 FLOOR BOARD
1. Install the rear No. 3 floor board.
INSTALL REAR DECK FLOOR BOX
1. Install the rear deck floor box.
INSTALL REAR NO. 2 FLOOR BOARD
1. Install the rear No. 2 floor board.