ROOF HEADLINING REMOVAL

REMOVE REAR NO. 2 FLOOR BOARD
1. Remove the rear No. 2 floor board.
REMOVE REAR DECK FLOOR BOX
1. Remove the rear deck floor box.
REMOVE REAR NO. 3 FLOOR BOARD
1. Remove the rear No. 3 floor board.
REMOVE DECK FLOOR BOX RH
1. Remove the clip.
2. Disengage the 6 guides and remove the deck floor box RH.
REMOVE REAR FLOOR BOARD UPPER NO. 3 PLATE
1. Disengage the 4 claws and 2 guides, and remove the rear floor board upper No. 3 plate.

REMOVE REAR SEAT CUSHION ASSEMBLY

Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

Note

Follow the instructions below carefully as the cushion frame can be deformed easily.

Text in Illustration
*1	Hook
*2	Guide

Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

Repeat the step above for the other hook.

Disengage the guide of the seat cushion from the seatback.
Standard Measurement

*a 100 mm (3.94 in.) or less

Remove the bolt and disconnect the rear center seat outer belt assembly.
Pull out the rear center seat outer belt assembly from the rear seat cushion assembly.
Remove the rear seat cushion assembly.

REMOVE REAR SEAT CUSHION LOCK HOOK
1. Disengage the claw and remove the rear seat cushion lock hook.
  
  Note
  
  Rear seat cushion lock hooks must not be reused.
  
  Tech Tips
  
  Use the same procedure the LH side and RH side.
REMOVE REAR SEATBACK ASSEMBLY RH
1. Disengage the fastener and disconnect the rear No. 1 floor board sub-assembly.
2. Remove the 2 bolts and rear seatback assembly RH.
  
  Note
  
  Be careful not to damage the vehicle body.
REMOVE REAR SEATBACK ASSEMBLY LH
1. Disengage the fastener and disconnect the rear No. 2 floor board sub-assembly.
2. Remove the 2 bolts and rear seatback assembly LH.
  
  Note
  
  Be careful not to damage the vehicle body.
REMOVE REAR NO. 4 FLOOR BOARD (w/o Woofer)
1. Remove the rear No. 4 floor board.
REMOVE REAR NO. 4 FLOOR BOARD (w/ Woofer)
1. Disengage the 2 clips and 3 guides, and remove the rear No. 4 floor board.
REMOVE DECK FLOOR BOX LH (w/o Woofer)
1. Remove the clip.
2. Disengage the 6 guides and remove the deck floor box LH.
REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
1. Remove the tonneau cover assembly.
REMOVE REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY
1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board sub-assembly.
REMOVE REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY
1. Disengage the claw and 2 clips, and remove the rear No. 2 floor board sub-assembly.
REMOVE REAR NO. 1 FLOOR BOARD
1. Remove the bolt.
2. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board.
REMOVE DECK TRIM SERVICE HOLE COVER
1. Disengage the 2 claws and guide (A).
2. Disengage the 2 guides (B) and remove the deck trim service hole cover.
REMOVE REAR DECK TRIM COVER
1. Disengage the 4 clips and remove the rear deck trim cover.
REMOVE FRONT SEAT ASSEMBLY

for Manual Seat Click here

for Power Seat Click here

Tech Tips

Use the same procedure for the RH side and LH side.
REMOVE FRONT DOOR SCUFF PLATE LH
1. Disengage the 4 claws, 2 guides and 4 clips, and remove the front door scuff plate LH.
REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
1. Disengage the 2 clips, claw and 2 guides.
2. Disengage the clamp.
3. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
1. Remove the clip as shown in the illustration.
2. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
1. Remove the front door opening trim weatherstrip LH.
2. Remove the residual weatherstrip sealant from the body of the vehicle using cleaner.
  
  Note
  
  Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.

Standard Measurement
*a	100 mm (3.94 in.) or less

REMOVE FRONT PILLAR GARNISH LH

Text in Illustration

*1 Front Pillar Garnish Clip

Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

Tech Tips

Make the front pillar garnish LH hang down from the front pillar garnish clip.
Text in Illustration

*1 Protective Tape

Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.
Note
- Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.
- Replace the front pillar garnish clips with new ones if they are removed from the vehicle.
Tech Tips

Tape the tips of the needle-nosed pliers before use.
Disengage the 2 guides.
w/o Front Center Speaker:
1. Remove the front pillar garnish LH by pulling it in the direction indicated by the arrow (2) in the illustration.
w/ Front Center Speaker:
1. Disconnect the front pillar garnish LH by pulling it in the direction indicated by the arrow (2) in the illustration.
2. Disconnect the connector and remove the front pillar garnish LH.

Text in Illustration
*1	Front Pillar Garnish Clip

Text in Illustration
*1	Protective Tape

Text in Illustration
*1	Adhesive Tape
*2	Protective Cover
*3	Curtain Shield Airbag Assembly

Protect the curtain shield airbag assembly.

Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.

Note

Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

REMOVE REAR DOOR SCUFF PLATE LH
1. Disengage the 4 claws, 2 guides and 2 clips, and remove the rear door scuff plate LH.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
1. Remove the rear door opening trim weatherstrip LH.
2. Remove the residual weatherstrip sealant from the body of the vehicle using cleaner.
  
  Note
  
  Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.
REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)
1. Disengage the 3 claws and remove the lap belt outer anchor cover.
DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
1. Remove the bolt and disconnect the floor end of the front seat outer belt assembly.
REMOVE CENTER PILLAR LOWER GARNISH LH
1. Disengage the 4 claws and 2 clips, and remove the center pillar lower garnish LH.
REMOVE CENTER PILLAR UPPER GARNISH LH
1. Remove the screw.
2. Disengage the 2 clips.
3. Pass the floor anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.
REMOVE FRONT DOOR SCUFF PLATE RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE FRONT PILLAR GARNISH RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE REAR DOOR SCUFF PLATE RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

Tech Tips

Use the same procedure as for the LH side.
DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE CENTER PILLAR LOWER GARNISH RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE CENTER PILLAR UPPER GARNISH RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE REAR SEAT SIDE GARNISH LH
1. Remove the clip.
2. Disengage the 6 claws and remove the rear seat side garnish LH.
REMOVE ROPE HOOK ASSEMBLY (for LH Side)
1. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver, disengage the 2 claws.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
2. Remove the bolt and the rope hook assembly.
REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)
1. Remove the bolt.
2. Disengage the guide and remove the luggage hold belt striker assembly.
REMOVE TONNEAU COVER HOOK (for LH Side)
1. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver, disengage the 2 claws and pin, and remove the tonneau cover hook.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE TONNEAU COVER HOLDER CAP (for LH Side)
1. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver, disengage the claws and guide, and remove the tonneau cover holder cap.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH
1. Remove the bolt and disconnect the floor end of the rear seat outer belt assembly.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
1. Remove the 3 screws.
2. Disengage the 4 claws and 3 clips, and remove the deck trim side panel assembly LH.
REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH
1. Using a moulding remover, disengage the 3 claws and 2 guides, and disconnect the belt guide.
2. Disengage the 8 clips
3. Pass the floor anchor of the rear seat outer belt assembly LH through the roof side inner garnish assembly LH and remove the roof side inner garnish assembly LH.
REMOVE REAR SEAT SIDE COVER RH
1. Disengage the 3 claws and 2 clips, and remove the rear seat side cover RH.
REMOVE REAR SEAT SIDE GARNISH RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE ROPE HOOK ASSEMBLY (for RH Side)

Tech Tips

Use the same procedure as for the LH side.
REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

Tech Tips

Use the same procedure as for the LH side.
REMOVE TONNEAU COVER HOOK (for RH Side)
1. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver, disengage the 2 claws and pin, and remove the tonneau cover hook.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE TONNEAU COVER HOLDER CAP (for RH Side)

Tech Tips

Use the same procedure as for the LH side.
REMOVE NO. 2 ROOM LIGHT ASSEMBLY
1. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
2. Disconnect the connector and remove the No. 2 room light assembly.
DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

Click here
REMOVE BACK DOOR WEATHERSTRIP
1. Remove the back door weatherstrip.
2. Remove the residual weatherstrip sealant from the body of the vehicle using cleaner.
  
  Note
  
  Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.
REMOVE MAP LIGHT ASSEMBLY
1. Open the overhead console.
2. Disengage the 4 clips and 3 guides as shown in the illustration.
3. Disconnect the connector and remove the map light assembly.
REMOVE NO. 1 ROOM LIGHT ASSEMBLY
1. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws and remove the No. 1 room light lens.
2. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws and disconnect the No. 1 room light housing as shown in the illustration.
3. Text in Illustration
  
  *a Room Light Switch Base
  
  Disengage the 4 claws and disconnect the room light switch base from the No. 1 room light housing.
REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)
1. w/o Rear View Monitor System:
  1. Disengage the 2 guides and slide the inner rear view mirror stay holder cover as shown in the illustration.
  2. Disengage the 6 claws and remove the inner rear view mirror stay holder cover.
2. w/ Rear View Monitor System:
  1. Disengage the 2 guides and slide the inner rear view mirror stay holder cover as shown in the illustration.
  2. Disengage the 2 claws and remove the inner rear view mirror stay holder cover.
REMOVE RAIN SENSOR COVER (w/ Rain Sensor)
1. Disengage the 2 guides and disconnect the rain sensor cover as shown in the illustration.
2. Disengage the 2 claws and remove the rain sensor cover.
REMOVE PROTECTOR (w/ Humidity Sensor)
1. Disengage the 2 guides and slide the protector as shown in the illustration.
2. Disengage the 2 claws and remove the protector.
REMOVE ASSIST GRIP SUB-ASSEMBLY
1. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.
  
  Note
  
  Do not forcibly pry the assist grip covers to prevent them from being deformed.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
2. Disengage the 2 clips and remove the assist grip sub-assembly.
3. Remove the 2 clips from the vehicle body.
  
  Tech Tips
  
  Use the same procedure for the other 3 assist grip sub-assemblies.
REMOVE VISOR BRACKET COVER (for LH Side)
1. Using a moulding remover, disengage the 4 claws and remove the visor bracket cover LH.
REMOVE VISOR ASSEMBLY LH
1. Remove the 2 screws and the visor assembly LH.
REMOVE VISOR BRACKET COVER (for RH Side)

Tech Tips

Use the same procedure as for the LH side.
REMOVE VISOR ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.
REMOVE SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)
1. Remove the sliding roof opening trim moulding.
REMOVE VISOR HOLDER
1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.
2. Disengage the 2 claws and remove the visor holder.
  
  Tech Tips
  
  Use the same procedure for the other visor holder.
REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
1. w/ EC Mirror:
  1. Disconnect the inner rear view mirror connector.
2. w/ Humidity Sensor
  1. Disconnect the humidity sensor connector.
3. w/ Rain Sensor
  1. Disconnect the rain sensor connector.
4. Disengage the 3 clamps and disconnect the connector from the front pillar RH.
5. Disconnect the connector from the rear pillar RH.
6. Disengage the 3 clamps and disconnect the 2 connectors from the front pillar LH.
7. Remove the 3 clips.
8. Remove the roof headlining assembly from the vehicle through the back door.
  
  Note
  
  Do not damage the roof headlining assembly or body interior.
REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
1. w/ EC Mirror:
  1. Disconnect the inner rear view mirror connector.
2. w/ Humidity Sensor
  1. Disconnect the humidity sensor connector.
3. w/ Rain Sensor
  1. Disconnect the rain sensor connector.
4. Disengage the 3 clamps and disconnect the connector from the front pillar RH.
5. Disconnect the connector from the rear pillar RH.
6. Disengage the 3 clamps and disconnect the 2 connectors from the front pillar LH.
7. Disconnect the connector from the sliding roof drive gear assembly.
8. Remove the 3 clips.
9. Remove the roof headlining assembly from the vehicle through the back door.
  
  Note
  
  Do not damage the roof headlining assembly or body interior.