UPPER INSTRUMENT PANEL INSTALLATION

INSTALL UPPER INSTRUMENT PANEL ASSEMBLY
1. Engage the 5 guides.
  
  Note
  
  Do not damage the upper instrument panel assembly.
2. Engage the 12 claws.
3. Install the upper instrument panel assembly with the 2 bolts <A> and 2 screws <B>.
  
  Torque:
  
  Bolt <A>
  
  20 N*m { 204 kgf*cm, 15 ft.*lbf }
4. Engage the clamp.
5. Connect each connector.
CONNECT NO. 3 INSTRUMENT PANEL WIRE
1. Check that the power switch is off.
2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
3. Connect the connector.
  
  Note
  
  When connecting any airbag connector, take care not to damage the airbag wire harness.
INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Navigation System)
1. Engage the 16 claws to install the instrument cluster finish panel sub-assembly.
INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY
1. Connect the connector.
2. Engage the 3 guides and 8 claws to install the center instrument panel register assembly.
INSTALL FRONT NO. 4 SPEAKER ASSEMBLY (w/ Front Center Speaker)
1. Connect the connector.
2. Install the front No. 4 speaker assembly with the 2 bolts.
  
  Note
  
  Do not touch the speaker cone.
  
  Tech Tips
  
  Install the bolts in the order shown in the illustration.
INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY
1. Engage the 4 clips to install the No. 1 speaker opening cover assembly.
INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (w/ Front No. 2 Speaker)
1. Connect the connector.
2. Install the front No. 2 speaker assembly with the 2 bolts.
  
  Note
  
  Do not touch the speaker cone.
  
  Tech Tips
  
  Install the bolts in the order shown in the illustration.
INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
1. Engage the 2 guides and 2 clips to install the No. 2 instrument panel speaker panel sub-assembly.
INSTALL NO. 1 DEFROSTER NOZZLE OPENING PLATE
1. Engage the 5 claws to install the No. 1 defroster nozzle opening plate.
INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
1. Engage the 3 guides and 4 claws to install the No. 1 instrument panel register assembly.

INSTALL FRONT PILLAR GARNISH LH

Remove the protective cover.

Text in Illustration
*1	Front Pillar Garnish Clip
*2	Protective Tape

Make sure that the front pillar garnish clip is not damaged.

Note

If there is any damage, replace the garnish clip with a new one.
When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

Engage the 2 guides by moving the garnish in the direction indicated by the arrow (1).
Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.

Tech Tips

Tape the tips of the needle-nosed pliers before use.
Engage the 2 clips to install the front pillar garnish LH.

INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
1. Connect each connector.
2. Engage the 8 claws and clip to install the lower instrument panel finish panel sub-assembly.
INSTALL INSTRUMENT SIDE PANEL LH
1. Engage the 4 guides, clip and 3 claws to install the instrument side panel LH.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
1. Text in Illustration
  
  *a Alignment Mark (Orange)
  
  Align the alignment mark (orange) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (w/ Front No. 2 Speaker)

Tech Tips

Use the same procedure described for the LH side.
INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

Tech Tips

Use the same procedure described for the LH side.
INSTALL NO. 2 DEFROSTER NOZZLE OPENING PLATE
1. Engage the 4 claws to install the No. 2 defroster nozzle opening plate.
INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
1. Engage the 3 guides and 7 claws to install the No. 2 instrument panel register assembly.
INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for Metal Finish Panel and Urethane Panel)
1. Engage the 5 clips to install the No. 3 instrument cluster finish panel garnish.
INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for Wood Panel and Bamboo Panel)
1. Engage the 4 clips to install the No. 3 instrument cluster finish panel garnish.
INSTALL FRONT PILLAR GARNISH RH

Tech Tips

Use the same procedure described for the LH side.
INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
1. Connect the connector.
2. Engage the clamp.
3. Engage the 5 claws.
4. Install the glove compartment door assembly with the 4 screws <C>.
INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY
1. Check that the power switch is off.
2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
  
  CAUTION:
  
  Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
3. Connect the airbag connector to the lower No. 2 instrument panel airbag assembly.
  
  Note
  
  When connecting any airbag connector, take care not to damage the airbag wire harness.
4. Push in the lock to install the airbag connector.
5. Temporarily install the lower No. 2 instrument panel airbag assembly with the 6 claws and 2 guides.
6. Install the 3 bolts.
  
  Torque:
  
  10 N*m { 102 kgf*cm, 7 ft.*lbf }
  
  Note
  
  Confirm that the lower No. 2 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side Click here.
INSTALL FRONT DOOR SCUFF PLATE RH

Tech Tips

Use the same procedure described for the LH side Click here.
INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)
1. Connect the connector.
2. Engage the clamp.
3. Engage the guide, claw and 2 clips to install the No. 2 instrument panel under cover sub-assembly.
INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
1. Connect the connector.
2. Engage the clamp.
3. Engage the 2 guides, claw and 2 clips to install the No. 2 instrument panel under cover sub-assembly.
INSTALL INSTRUMENT SIDE PANEL RH
1. Connect the connector.
2. Engage the 4 guides, clip and 3 claws to install the instrument side panel RH.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
1. Text in Illustration
  
  *a Alignment Mark (Light blue)
  
  Align the alignment mark (light blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL COMBINATION METER ASSEMBLY
1. Connect the connector.
2. Engage the 2 clips.
3. Install the combination meter assembly with the 2 screws.
4. Engage the clamp.
INSTALL METER HOOD SUB-ASSEMBLY
1. Connect the connector.
2. Engage the 11 claws.
3. Engage the 2 guides and 4 clips to install the meter hood sub-assembly.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSTALL REAR FLOOR BOARD UPPER NO. 3 PLATE
1. Engage the 4 claws and 2 guides to install the rear floor board upper No. 3 plate.
INSTALL DECK FLOOR BOX RH
1. Engage the 6 guides.
2. Install the deck floor box RH with the clip.
INSTALL REAR NO. 3 FLOOR BOARD
1. Install the rear No. 3 floor board.
INSTALL REAR DECK FLOOR BOX
1. Install the rear deck floor box.
INSTALL REAR NO. 2 FLOOR BOARD
1. Install the rear No. 2 floor board.
PERFORM DIAGNOSTIC SYSTEM CHECK

Click here
INSPECT SRS WARNING LIGHT

Click here