REAR SEAT OUTER BELT ASSEMBLY INSTALLATION

INSTALL REAR SEAT OUTER BELT ASSEMBLY
1. Temporarily install the rear seat outer belt assembly.
2. Install the bolt <C>.
  
  Torque:
  
  7.5 N*m { 77 kgf*cm, 66 in.*lbf }
3. Install the rear seat outer belt assembly with the bolt <B>.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
4. Install the shoulder anchor of the rear seat outer belt assembly with the bolt <A>.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
5. w/ Pretensioner:
  1. Text in Illustration
    
    *1 Pretensioner Connector
    
    Connect the pretensioner connector and lock the locking button as shown in the illustration.
    
    Note
    
    Securely lock the locking button.
INSTALL ROOF SIDE INNER GARNISH ASSEMBLY
1. Pass the floor anchor of the rear seat outer belt assembly LH through the roof side inner garnish LH.
2. Engage the 8 clips to install the roof side inner garnish assembly LH.
3. Engage the 2 guides.
4. Engage the 3 claws to connect the belt guide.
INSTALL DECK TRIM SIDE PANEL ASSEMBLY
1. Engage the 4 claws and 3 clips.
2. Install the deck trim side panel assembly LH with the 3 screw.
CONNECT REAR SEAT OUTER BELT ASSEMBLY
1. Text in Illustration
  
  *1 Protruding Part
  
  Connect the floor end of the rear seat outer belt assembly with the bolt.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
  
  Note
  
  Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.
INSTALL NO. 2 ROOM LIGHT ASSEMBLY (for RH Side)
1. Connect the connector.
2. Engage the claw to install the No. 2 room light assembly.
INSTALL TONNEAU COVER HOLDER CAP
1. Engage the guide.
2. Engage the claw to install the tonneau cover holder cap.
INSTALL TONNEAU COVER HOOK
1. Engage the 2 claws and pin to install the tonneau cover hook.
INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY
1. Engage the guide.
2. Install the luggage hold belt striker assembly with the bolt.
INSTALL ROPE HOOK ASSEMBLY
1. Install the rope hook assembly with the bolt.
2. Engage the 2 claws.
INSTALL REAR SEAT SIDE GARNISH
1. Engage the 6 claws.
2. Install the rear seat side garnish LH with the clip.
INSTALL REAR SEAT SIDE COVER RH (for RH Side)
1. Engage the 3 claws and 2 clips to install the rear seat side cover RH.
INSTALL REAR DECK TRIM COVER
1. Engage the 4 clips to install the rear deck trim cover.
INSTALL DECK TRIM SERVICE HOLE COVER
1. Engage the 2 guides (B).
2. Engage the 2 claws and guide (A) to install the deck trim service hole cover.
INSTALL REAR NO. 1 FLOOR BOARD
1. Engage the 2 claws and 2 clips.
2. Install the rear No. 1 floor board with the bolt.
INSTALL REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY
1. Engage the claw and 2 clips to install the rear No. 2 floor board sub-assembly.
INSTALL REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY
1. Engage the 2 claws and 2 clips to install the rear No. 1 floor board sub-assembly.
INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
1. Install the tonneau cover assembly.
INSTALL DECK FLOOR BOX LH (w/o Woofer)
1. Engage the 6 guides.
2. Install the deck floor box LH with the clip.
INSTALL REAR NO. 4 FLOOR BOARD (w/o Woofer)
1. Install the rear No. 4 floor board.
INSTALL REAR NO. 4 FLOOR BOARD (w/ Woofer)
1. Engage the 2 clips and 3 guides to install the rear No. 4 floor board.
INSTALL REAR SEATBACK ASSEMBLY RH (for RH Side)
1. Place the rear seatback assembly RH in the cabin.
  
  Note
  
  Be careful not to damage the vehicle body.
2. Install the rear seatback assembly RH with the 2 bolts.
  
  Torque:
  
  37 N*m { 375 kgf*cm, 27 ft.*lbf }
3. Engage the fastener to connect the rear No. 1 floor board sub-assembly.
INSTALL REAR SEAT CUSHION LOCK HOOK
1. Engage the claw to install a new rear seat cushion lock hook.
  
  Note
  
  Rear seat cushion lock hooks must not be reused.
  
  Tech Tips
  
  Use the same procedure the LH side and RH side.

Text in Illustration
*1	Pretensioner Connector

Text in Illustration
*1	Protruding Part

INSTALL REAR SEAT CUSHION ASSEMBLY

Place the rear seat cushion assembly in the cabin.

Note

Be careful not to damage the vehicle body.
Pass the rear center seat outer belt assembly through the rear seat cushion assembly.
Install the rear center seat outer belt assembly with the bolt.

Torque:

42 N*m { 428 kgf*cm, 31 ft.*lbf }
Engage the guide as shown in the illustration.

Pass the rear seat inner with center belt assembly LH and rear seat inner belt assembly through the rear seat cushion assembly as shown in the illustration.

Text in Illustration
*1	Rear Seat Inner Belt Assembly	*2	Rear Seat Inner with Center Belt Assembly LH

Engage the 2 hooks of the seat cushion to the vehicle body as shown in the illustration.
Confirm that the seat cushion is firmly installed.

Note

When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

INSTALL REAR SEATBACK ASSEMBLY LH (for LH Side)
1. Place the rear seatback assembly LH in the cabin.
  
  Note
  
  Be careful not to damage the vehicle body.
2. Install the rear seatback assembly LH with the 2 bolts.
  
  Torque:
  
  37 N*m { 375 kgf*cm, 27 ft.*lbf }
3. Engage the fastener to connect the rear No. 2 floor board sub-assembly.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP

for LH Side: Click here

for RH Side: Click here
INSTALL REAR DOOR SCUFF PLATE
1. Engage the 4 claws, 2 guides and 2 clips to install the rear door scuff plate LH.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSTALL REAR FLOOR BOARD UPPER NO. 3 PLATE (for RH Side)
1. Engage the 4 claws and 2 guides to install the rear floor board upper No. 3 plate.
INSTALL DECK FLOOR BOX RH
1. Engage the 6 guides.
2. Install the deck floor box RH with the clip.
INSTALL REAR NO. 3 FLOOR BOARD
1. Install the rear No. 3 floor board.
INSTALL REAR DECK FLOOR BOX
1. Engage the 6 guides.
2. Install the deck floor box RH with the clip.
INSTALL REAR NO. 2 FLOOR BOARD
1. Install the rear No. 2 floor board.
INSPECT SRS WARNING LIGHT

Click here