FRONT SEAT OUTER BELT ASSEMBLY REMOVAL


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work Click here.

  2. REMOVE REAR NO. 2 FLOOR BOARD


    1. Remove the rear No. 2 floor board.

  3. REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  4. REMOVE REAR NO. 3 FLOOR BOARD


    1. Remove the rear No. 3 floor board.

  5. REMOVE DECK FLOOR BOX RH


    1. A003Z5J

      Remove the clip.

    2. Disengage the 6 guides and remove the deck floor box RH.

  6. REMOVE REAR FLOOR BOARD UPPER NO. 3 PLATE


    1. A003VKN

      Disengage the 4 claws and 2 guides, and remove the rear floor board upper No. 3 plate.

  7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. REMOVE FRONT DOOR SCUFF PLATE


    1. A003VX8

      Disengage the 4 claws, 2 guides and 4 clips, and remove the front door scuff plate LH.

  9. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. A003VC3

      Disengage the 2 clips, claw and 2 guides.

    2. Disengage the clamp.

    3. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.

  10. REMOVE COWL SIDE TRIM SUB-ASSEMBLY


    1. A003X2U

      Remove the clip as shown in the illustration.

    2. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.

  11. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP


    1. Remove the front door opening trim weatherstrip LH.

    2. Remove the residual weatherstrip sealant from the body of the vehicle using cleaner.

      Note

      Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.

  12. REMOVE REAR DOOR SCUFF PLATE


    1. A003ZA0

      Disengage the 4 claws, 2 guides and 2 clips, and remove the rear door scuff plate LH.

  13. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP


    1. Remove the rear door opening trim weatherstrip LH.

    2. Remove the residual weatherstrip sealant from the body of the vehicle using cleaner.

      Note

      Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.

  14. REMOVE LAP BELT OUTER ANCHOR COVER


    1. A003WAO

      Disengage the 3 claws and remove the lap belt outer anchor cover.

  15. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY


    1. A003ZN2

      Remove the bolt and disconnect the floor end of the front seat outer belt assembly.

  16. REMOVE CENTER PILLAR LOWER GARNISH


    1. A003ZLT

      Disengage the 4 claws and 2 clips, and remove the center pillar lower garnish LH.

  17. REMOVE CENTER PILLAR UPPER GARNISH


    1. A003YUB

      Remove the screw.

    2. Disengage the 2 clips.

    3. Pass the floor anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.

  18. REMOVE FRONT SEAT OUTER BELT ASSEMBLY


    1. A003V5T

      Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly.

    2. A003YMXE01
      Text in Illustration
      *A w/ Pre-crash Safety System
      *1 Pretensioner Connector

      Using a screwdriver, pull out the locking button in the direction shown by the arrow in the illustration to release the lock, and disconnect the pretensioner connector as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    3. Disconnect the connector.

    4. w/ Pre-crash Safety System:


      1. Disconnect the connector.

    5. A003VK8

      Remove the 2 bolts and front seat outer belt assembly.

  19. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    1. A003VNS

      Remove the 2 bolts.

    2. Disengage the guide and remove the front shoulder belt anchor adjuster assembly.