AIR CONDITIONING SYSTEM, Diagnostic DTC:B1441/41

DTC Code DTC Name
B1441/41 Air Mix Damper Control Servo Motor Circuit (Passenger Side)

DESCRIPTION

The air mix control servo motor (for front passenger side) sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the air mix control servo motor (for front passenger side) to any position. As a result, the amount of air passing through the heater core after passing through the evaporator is adjusted, and the temperature of the air blowing toward the passenger side is controlled.

The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

Tech Tips

Confirm that no mechanical problem is present because this DTC can be stored when either a damper link or the damper is mechanically locked.

DTC No. DTC Detection Condition Trouble Area
B1441/41 Air mix damper position sensor value does not change even if air conditioning amplifier assembly operates air mix control servo motor

  • Air mix control servo motor (for front passenger side)

  • Air conditioning harness assembly

  • Air conditioning amplifier assembly

WIRING DIAGRAM

A003ZGTE04

INSPECTION PROCEDURE

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Operate the front passenger side temperature adjustment switch.

    5. Enter the following menus: Body / Air Conditioner / Data List.

    6. Check the value(s) by referring to the table below.

      Air Conditioner
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Air Mix Servo Targ Pulse (P) Front passenger side air mix servo motor target pulse / Min.: 0, Max.: 255

      for LHD:

      MAX. COLD: 6 (pulse)

      MAX. HOT: 93 (pulse)

      for RHD:

      MAX. COLD: 92 (pulse)

      MAX. HOT: 5 (pulse)

      		 -
      Air Mix Servo Actual Pulse (P) Front passenger side air mix servo motor actual pulse / Min.: 0, Max.: 255

      for LHD:

      MAX. COLD: 6 (pulse)

      MAX. HOT: 93 (pulse)

      for RHD:

      MAX. COLD: 92 (pulse)

      MAX. HOT: 5 (pulse)

      		 -
      OK
      The display is as specified in the Normal Condition column.
      Result
      Result Proceed to
      NG A
      OK (When troubleshooting according to Problem Symptoms Table) B
      OK (When troubleshooting according to the DTC) C

    B

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    C

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    A

  2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Air Conditioner / Active Test.

    5. Check the operation by referring to the table below.

      Air Conditioner
      Tester Display Test Part Control Range Diagnostic Note
      Air Mix Servo Targ Pulse (P) Air mix servo motor pulse (for front passenger side) Min.: 0, Max.: 255 -
      OK
      Air temperature changes in accordance with each control range.

    NG

    INSPECT AIR MIX CONTROL SERVO MOTOR (FOR FRONT PASSENGER SIDE) Click here

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

  3. INSPECT AIR MIX CONTROL SERVO MOTOR (FOR FRONT PASSENGER SIDE)


    1. Replace the air mix control servo motor (for front passenger side) Click here.

      Tech Tips

      Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

    2. Check for the DTC.

      Result
      Result Proceed to
      DTC B1441/41 is output A
      DTC B1441/41 is not output B

    B

    END (AIR MIX CONTROL SERVO MOTOR WAS DEFECTIVE)

    A

  4. INSPECT AIR CONDITIONING HARNESS ASSEMBLY


    1. Replace the air conditioning harness assembly Click here.

      Tech Tips

      Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or a known good one and check that the condition returns to normal.

    2. Check for the DTC.

      Result
      Result Proceed to
      DTC B1441/41 is output A
      DTC B1441/41 is not output B

    B

    END (AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)

    A

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here