REAR SEAT ASSEMBLY REASSEMBLY


  1. INSTALL REAR SEATBACK LOCK ASSEMBLY LH


    1. A003Y9C

      Install the rear seatback lock assembly LH with the 2 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 16 ft.*lbf }

  2. INSTALL NO. 2 REAR SEATBACK EDGE PROTECTOR


    1. Clean the installation surface of the rear seatback frame sub-assembly LH.

    2. Attach the 4 pieces of double-sided tape and install the No. 2 rear seatback edge protector to the rear seatback frame sub-assembly LH.

      A003YUIE01
      Text in Illustration
      *1 Double-sided Tape - -
      *a No. 2 Rear Seatback Edge Protector *b Front Side of Rear Seatback Frame LH
      *c Upper Limit of Headrest Support Bracket *d Insert
      *e Reference Line *f Back Side of Rear Seatback Frame LH

  3. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH


    1. Insert the rod of the rear seatback lock assembly LH to the rear seat lock control lever sub-assembly LH as shown in the illustration.

      A003X1O
    2. A003XTI

      Engage the guide.

    3. Install the rear seat lock control lever sub-assembly LH with the 2 screws.

  4. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH


    1. A003X2K

      Using hog ring pliers, install the separate type rear seatback cover LH to the separate type rear seatback pad LH with 11 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  5. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD LH


    1. Temporarily install the separate type rear seatback cover with pad LH to the rear seatback frame sub-assembly LH.

    2. A003X5D

      Engage the 4 claws to install the 2 rear seat headrest supports.

    3. A003XYC

      Engage the 2 hooks.

    4. A003WO3

      Engage the 8 hooks.

    5. Install 9 new clips to the separate type rear seatback cover LH.

    6. A003WGQE01
      Text in Illustration
      *1 Fastener

      Engage the 9 clips.

    7. Engage the fastener.

    8. A003WF4

      Install the separate type rear seatback cover with pad LH with 2 new clips.

  6. INSTALL REAR SEATBACK COVER LH


    1. A003YEK

      Engage the 4 claws to install the rear seatback cover LH.

  7. INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE LH


    1. A003YEU

      Engage the 5 claws.

    2. Install the rear seatback lock control lever base LH with the screw.

  8. INSTALL REAR SEATBACK LOCK STRIKER COVER LH


    1. A003Z2G

      Engage the 2 guides and claw to install the rear seatback lock striker cover LH.

  9. INSTALL REAR SEATBACK LOCK ASSEMBLY RH


    1. A003WZ3

      Install the rear seatback lock assembly RH with the 2 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 16 ft.*lbf }

  10. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY


    1. A003WVEE01
      Text in Illustration
      *1 Protruding Part

      Install the rear center seat outer belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the rear center seat outer belt assembly to overlap the protruding part of the rear seatback frame.

  11. INSTALL REAR SEATBACK EDGE PROTECTOR


    1. Clean the installation surface of the rear seatback frame sub-assembly RH.

    2. Attach the 12 pieces of double-sided tape and install the rear seatback edge protector to the rear seatback frame sub-assembly RH.

      A003VTPE01
      Text in Illustration
      *1 Double-sided Tape - -
      *a Rear Seatback Edge Protector *b Front Side of Rear Seatback Frame RH
      *c Upper Limit of Headrest Support Bracket *d Insert
      *e Reference Line *f Bask Side of Rear Seatback Frame RH

  12. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH


    1. Insert the rod of the rear seatback lock assembly RH to the rear seat lock control lever sub-assembly RH as shown in the illustration.

      A003ZHX
    2. A003VMS

      Engage the guide.

    3. Install the rear seat lock control lever sub-assembly RH.

  13. INSTALL SEPARATE TYPE REAR SEATBACK COVER RH


    1. A003XGD

      Using hog ring pliers, install the separate type rear seatback cover RH to the separate type rear seatback pad RH with 9 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    2. A003W06

      Engage the 2 hooks.

  14. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD RH


    1. Temporarily install the separate type rear seatback cover with pad RH to the rear seatback frame sub-assembly RH.

    2. A003VLO

      Engage the 4 claws to install the 2 rear seat center headrest supports.

    3. A003Y24

      Engage the 4 claws to install the 2 rear seat headrest supports.

    4. A003VY7

      Engage the 4 hooks.

    5. A003YP2

      Engage the 10 hooks.

    6. Install 9 new clips to the separate type rear seatback cover RH.

    7. A003ZVW

      Engage the 9 clips.

    8. A003WLX

      Install the separate type rear seatback cover with pad RH with 3 new clips.

  15. INSTALL REAR SEATBACK COVER RH


    1. A003ZGP

      Engage the 4 claws to install the rear seatback cover RH.

    2. w/ Rear Seatback Cover:


      1. Install the rear seatback cover RH.

        Tech Tips

        Use the same procedure for the LH side and RH side.

  16. INSTALL REAR SEAT SHOULDER BELT COVER


    1. A003WR5

      Engage the 4 claws to install the rear seat shoulder belt cover.

  17. INSTALL SEAT BELT ANCHOR COVER CAP


    1. A003VDC

      Engage the 2 claws to install the seat belt anchor cover cap.

  18. INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE RH


    1. A003ZN4

      Engage the 5 claws.

    2. Install the rear seatback lock control lever base RH with the screw.

  19. INSTALL REAR SEATBACK LOCK STRIKER COVER RH


    1. A003VBS

      Engage the 2 guides and claw to install the rear seatback lock striker cover RH.

  20. INSTALL BENCH TYPE REAR SEAT CUSHION COVER


    1. Using hog ring pliers, install 24 new hog rings.

      A003YIO
    2. A003YZP

      Using hog ring pliers, install 22 new hog rings.

    3. A003YI6

      Using hog ring pliers, install the bench type rear seat cushion cover to the bench type rear seat cushion pad with 21 new hog rings.