SEAT BELT CONTROL ECU INSTALLATION


  1. INSTALL SEAT BELT CONTROL ECU (for LHD)


    1. A003ZW1

      Engage the 2 claws to install the seat belt control ECU.

  2. INSTALL SEAT BELT CONTROL ECU (for RHD)


    1. A003XJ1

      Engage the 2 claws to install the seat belt control ECU.

  3. INSTALL ECU INTEGRATION BOX RH (for LHD)


    1. Install the ECU integration box RH with the 2 nuts and bolt.

    2. Engage the clamp to connect the wire harness.

    3. Connect each connector.

  4. INSTALL ECU INTEGRATION BOX LH (for RHD)


    1. Install the ECU integration box LH with the nut and bolt.

    2. Engage the clamp to connect the wire harness.

    3. Connect each connector.

  5. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    1. Connect the connector.

    2. Engage the clamp.

    3. Engage the 5 claws.

    4. Install the glove compartment door assembly with the 4 screws <C>.

  6. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A003ZOW

      Connect the airbag connector to the lower No. 2 instrument panel airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the lock to install the airbag connector.

    5. Temporarily install the lower No. 2 instrument panel airbag assembly with the 6 claws and 2 guides.

    6. Install the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the lower No. 2 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  7. INSTALL INSTRUMENT SIDE PANEL


    1. Connect the connector.

    2. A003YNR

      Engage the 4 guides, clip and 3 claws to install the instrument side panel RH.

  8. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP


    1. A003W54E01
      Text in Illustration
      *a Alignment Mark (Light blue)

      Align the alignment mark (light blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  9. INSTALL COWL SIDE TRIM SUB-ASSEMBLY

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  10. INSTALL FRONT DOOR SCUFF PLATE

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  11. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. Connect the connector.

    2. Engage the clamp.

    3. Engage the guide, claw and 2 clips to install the No. 2 instrument panel under cover sub-assembly.

  12. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. Connect the connector.

    2. Engage the clamp.

    3. Engage the 2 guides, claw and 2 clips to install the No. 2 instrument panel under cover sub-assembly.

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  14. INSTALL REAR FLOOR BOARD UPPER NO. 3 PLATE


    1. Engage the 4 claws and 2 guides to install the rear floor board upper No. 3 plate.

  15. INSTALL DECK FLOOR BOX RH


    1. Engage the 6 guides.

    2. Install the deck floor box RH with the clip.

  16. INSTALL REAR NO. 3 FLOOR BOARD


    1. Install the rear No. 3 floor board.

  17. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  18. INSTALL REAR NO. 2 FLOOR BOARD


    1. Install the rear No. 2 floor board.

  19. INSPECT SRS WARNING LIGHT

    Click here