SEAT POSITION SENSOR INSTALLATION

Note


  • Use the same procedure for the driver side of RHD and LHD vehicles.

  • The procedures listed below are for the driver side of an LHD vehicle.


  1. INSTALL SEAT POSITION AIRBAG SENSOR (for Manual Seat)


    1. A003XB8

      Install the seat position airbag sensor to the seat slide position sensor protector with the pin as shown in the illustration.

    2. A003Z0LE12
      Text in Illustration
      *1 Seat Position Airbag Sensor
      *2 Feeler Gauge
      *3 Seat Rail

      Using a 1.3 mm (0.0512 in.) feeler gauge, temporarily install the seat position airbag sensor with the "TORX" screw.

      Note


      • If the seat position airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position airbag sensor with a new one.

      • When installing the seat position airbag sensor, be careful that the SRS wiring does not interfere with or is pinched between other parts.

      Tech Tips

      Be sure that the clearance between the seat position airbag sensor and seat rail is between 0.6 mm (0.0236 in.) and 2.0 mm (0.0787 in.).

    3. Using a T30 "TORX" socket wrench, tighten the "TORX" screw to install the seat position airbag sensor.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    4. Make sure that the clearance between the seat position airbag sensor and seat rail is between 0.6 mm (0.0236 in.) and 2.0 mm (0.0787 in.).

    5. Connect the connector.

    6. Install the wire harness to the 2 hooks.

    7. Check that there is no looseness in the installation parts of the seat position airbag sensor.

  2. INSTALL SEAT POSITION AIRBAG SENSOR (for Power Seat)


    1. A003XB8

      Install the seat position airbag sensor to the seat slide position sensor protector with the pin as shown in the illustration.

    2. A003Z0LE12
      Text in Illustration
      *1 Seat Position Airbag Sensor
      *2 Feeler Gauge
      *3 Seat Rail

      Using a 1.3 mm (0.0512 in.) feeler gauge, temporarily install the seat position airbag sensor with the "TORX" screw and nut.

      Note


      • If the seat position airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position airbag sensor with a new one.

      • When installing the seat position airbag sensor, be careful that the SRS wiring does not interfere with or is pinched between other parts.

      Tech Tips

      Be sure that the clearance between the seat position airbag sensor and seat rail is between 0.6 mm (0.0236 in.) and 2.0 mm (0.0787 in.).

    3. Using a T30 "TORX" socket wrench, install the seat position airbag sensor with the "TORX" screw and nut.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    4. Make sure that the clearance between the seat position airbag sensor and seat rail is between 0.6 mm (0.0236 in.) and 2.0 mm (0.0787 in.).

    5. Connect the connector.

    6. Install the wire harness to the 2 hooks.

    7. Check that there is no looseness in the installation parts of the seat position airbag sensor.

  3. INSTALL FRONT SEAT CUSHION SHIELD LH (for Manual Seat)


    1. A003X3J

      Engage the clip.

    2. Engage the 11 claws.

    3. Install the front seat cushion shield with the screw.

  4. INSTALL VERTICAL ADJUSTING HANDLE LH (for 6 Way Seat Type)


    1. A003ZAO

      Install the vertical adjusting handle with the screw.

  5. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH (for Manual Seat)


    1. A003V2M

      Engage the claw to install the reclining adjuster release handle.

  6. INSTALL FRONT SEAT ASSEMBLY LH

    for Manual Seat: Click here

    for Power Seat: Click here

  7. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here