AIRBAG SYSTEM, Diagnostic DTC:B1825/56, B1826/56, B1827/56, B1828/56

DTC Code DTC Name
B1825/56 Short in Side Squib LH Circuit
B1826/56 Open in Side Squib LH Circuit
B1827/56 Short to GND in Side Squib LH Circuit
B1828/56 Short to B+ in Side Squib LH Circuit

DESCRIPTION

The side squib LH circuit consists of the airbag sensor assembly and front seat airbag assembly LH.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the side squib LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1825/56

  • The airbag sensor assembly receives a line short circuit signal in the side squib LH circuit during primary check.

  • Side squib LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Front seat airbag assembly LH (Side squib LH)

  • Airbag sensor assembly
B1826/56

  • The airbag sensor assembly receives an open circuit signal in the side squib LH circuit.

  • Side squib LH malfunction

  • Airbag sensor assembly malfunction
B1827/56

  • The airbag sensor assembly receives a short circuit to ground signal in the side squib LH circuit.

  • Side squib LH malfunction

  • Airbag sensor assembly malfunction
B1828/56

  • The airbag sensor assembly receives a short circuit to B+ signal in the side squib LH circuit.

  • Side squib LH malfunction

  • Airbag sensor assembly malfunction

WIRING DIAGRAM

A003XS6E13

INSPECTION PROCEDURE

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

Tech Tips


  • Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester Click here.

  • After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road Click here.

PROCEDURE


  1. CHECK CONNECTORS


    1. A003ZA3E26
      Text in Illustration
      *1 Front Seat Airbag Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the front seat airbag assembly LH and airbag sensor assembly.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the front seat airbag assembly LH and airbag sensor assembly.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    6. Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.

      OK
      The short spring is not deformed or damaged.

    NG

    REPLACE FLOOR WIRE

    OK

  2. CHECK FRONT SEAT AIRBAG ASSEMBLY LH (SIDE SQUIB LH)


    1. A003VCEE09
      Text in Illustration
      *1 Front Seat Airbag Assembly LH
      *2 Airbag Sensor Assembly
      *3 Connector C
      *a

      Front view of wire harness connector

      (to Front Seat Airbag Assembly LH)

      Connect the connector to the airbag sensor assembly.

    2. Connect SST (resistance 2.1 Ω) to connector C.

      CAUTION:

      Never connect the tester to the front seat airbag assembly LH (side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

      Note


      • Do not forcibly insert SST into the terminals of the connector when connecting.

      • Insert SST straight into the terminals of the connector.

      SST
      09843-18061

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Turn the power switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in memory Click here.

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs Click here.

      OK
      DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output.

      Tech Tips

      Codes other than DTCs B1825/56, B1826/56, B1827/56 and B1828/56 may be output at this time, but they are not related to this check.


    NG

    CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT) Click here

    OK

    REPLACE FRONT SEAT AIRBAG ASSEMBLY LH Click here

  3. CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)


    1. A003WTEE15
      Text in Illustration
      *1 Front Seat Airbag Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Front Seat Airbag Assembly LH)

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Disconnect SST from connector C.

    4. Disconnect the floor wire from the airbag sensor assembly.

    5. Check for a short to B+ in the circuit.


      1. Connect the cable to the negative (-) auxiliary battery terminal.

      2. Turn the power switch on (IG).

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        P2-1 (SFL+) - Body ground Power switch on (IG) Below 1 V
        P2-2 (SFL-) - Body ground Power switch on (IG) Below 1 V

    6. Check for an open in the circuit.


      1. Turn the power switch off.

      2. Disconnect the cable from the negative (-) auxiliary battery terminal.

        CAUTION:

        Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        P2-1 (SFL+) - P2-2 (SFL-) Always Below 1 Ω

    7. Check for a short to ground in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        P2-1 (SFL+) - Body ground Always 1 MΩ or higher
        P2-2 (SFL-) - Body ground Always 1 MΩ or higher

    8. Check for a short in the circuit.


      1. Release the activation prevention mechanism built into connector B Click here.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        P2-1 (SFL+) - P2-2 (SFL-) Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK AIRBAG SENSOR ASSEMBLY


    1. A003XH6E08
      Text in Illustration
      *1 Front Seat Airbag Assembly LH
      *2 Airbag Sensor Assembly

      Restore the released activation prevention mechanism of connector B to the original condition.

    2. Connect the connectors to the front seat airbag assembly LH and airbag sensor assembly.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Turn the power switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in memory Click here.

    6. Turn the power switch off.

    7. Turn the power switch on (IG), and wait for at least 60 seconds.

    8. Check for DTCs Click here.

      OK
      DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output.

      Tech Tips

      Codes other than DTCs B1825/56, B1826/56, B1827/56 and B1828/56 may be output at this time, but they are not related to this check.


    NG

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    OK

    USE SIMULATION METHOD TO CHECK Click here