METER / GAUGE SYSTEM Fuel Receiver Gauge Malfunction

DESCRIPTION

• The meter ECU uses the fuel sender gauge assembly to determine the level of the fuel in the fuel tank. The resistance of the fuel sender gauge will vary between approximately 12 Ω with the float at the full position, and 415 Ω with the float at the empty position. The meter outputs auxiliary battery voltage through two resistors of 820 Ω that are mounted in parallel inside the meter ECU. The meter ECU measures the voltage between the variable resistor in the fuel sender gauge and the two resistors mounted in parallel in the meter. Voltage measured at this point will vary as the float of the fuel sender gauge is moved. The highest voltage observed should be approximately half of the auxiliary battery voltage.

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL METER OPERATION)

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Enter following menus: Body / Combination Meter / Active Test.

   5. Check the operation by referring to the table below.

      Combination Meter

      Tester Display	Test Part	Control Range	Diagnostic Note
      Fuel Meter Operation	Fuel receiver gauge	Empty, 1/2, Full	-

      OK
      Fuel receiver gauge indication is normal.

   
   

   NG

   REPLACE COMBINATION METER ASSEMBLY Click here

   OK

2. READ VALUE USING INTELLIGENT TESTER (FUEL INPUT)

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Enter following menus: Body / Combination Meter / Data List.

   5. Check the values by referring to the table below.

      Combination Meter

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      Fuel Input	Fuel input signal/Min.: 0, Max.: 127.5	Fuel indicates F: 39.6	Unit: Liter
      		Fuel indicates 3/4: 31.0
      		Fuel indicates 1/2: 22.8
      		Fuel indicates 1/4: 14.3
      		Fuel indicates E: 5.1

      OK
      Fuel level signal displayed on the intelligent tester is almost the same as fuel receiver gauge indication.

   
   

   NG

   REPLACE COMBINATION METER ASSEMBLY Click here

   OK

3. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SENDER GAUGE ASSEMBLY)

   
   

   1. Disconnect the H19 and P9 connectors.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition H19-27 (L) - P9-2 (FS) Always Below 1 Ω H19-30 (FE) - P9-3 (FE) Always Below 1 Ω H19-27 (L) - Body ground Always 10 kΩ or higher H19-30 (FE) - Body ground Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

4. INSPECT FUEL SENDER GAUGE ASSEMBLY

   
   
   1. 

      Text in Illustration

      *a	Front view of wire harness connector (to Fuel Sender Gauge Assembly)

      Remove the fuel sender gauge assembly Click here.

   2. Check that the float moves smoothly between F and E.

   3. Check if the fuel sender gauge arm is deformed.

   4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 1 - 2 Float level is F (upper) 12 to 18 Ω 1 - 2 Float level is between F (upper) and E (lower) 12 to 415 Ω (Gradually changes) 1 - 2 Float level is E (lower) 405 to 415 Ω

   
   

   NG

   REPLACE FUEL SENDER GAUGE ASSEMBLY Click here

   OK

   REPLACE COMBINATION METER ASSEMBLY Click here