METER / GAUGE SYSTEM ON-VEHICLE INSPECTION


  1. INSPECT SPEEDOMETER


    1. Check speedometer operation.

      Note


      • The meter ECU receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.

      • The Data List values of the skid control ECU are used for this inspection. Therefore, make sure to perform the inspection after confirming that no DTCs are output from the brake control system.

      • If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform the inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.


      1. Before starting the following inspection, check if the Brake Control System outputs the DTCs.

      2. Check the values by referring to the table below.

        ABS/VSC/TRC
        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        Vehicle Speed Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) -
        Reference: km/h (for Australia)
        Intelligent Tester Indication (km/h) Acceptable Range (km/h)
        20 20.7 to 24.7
        40 41.3 to 45.8
        60 62.0 to 66.5
        80 82.6 to 87.6
        100 103.3 to 107.3
        120 123.9 to 128.9
        140 144.6 to 149.6
        160 165.2 to 170.2
        180 185.9 to 190.9
        200 206.5 to 211.5
        220 227.2 to 232.2
        Reference: km/h (except Australia)
        Intelligent Tester Indication (km/h) Acceptable Range (km/h)
        20 21.0 to 25.0
        40 41.7 to 46.2
        60 62.7 to 67.2
        80 83.4 to 88.4
        100 104.3 to 109.3
        120 125.1 to 130.6
        140 145.8 to 151.8
        160 166.2 to 173.2
        180 186.9 to 194.5
        200 207.7 to 215.7
        220 228.4 to 236.8
        240 249.2 to 258.0
        260 270.0 to 279.0
        Reference: mph
        Intelligent Tester Indication (mph) Acceptable Range (mph)
        20 21.0 to 23.5
        40 42.0 to 44.5
        60 62.5 to 66.0
        80 83.1 to 87.1
        100 103.9 to 108.4
        120 124.7 to 129.6
        140 145.4 to 150.7
        160 166.2 to 171.9
        180 187.0 to 193.0

  2. INSPECT TACHOMETER


    1. Connect the intelligent tester, and start the hybrid system.

    2. Compare the test results with the tachometer indications.

      DC 13.5 V, at 25°C (77°F)
      Intelligent Tester Indication (rpm)

      Acceptable Range

      Data in ( ) is for Reference
      700 (630 to 770)
      1000 (900 to 1100)
      2000 (1850 to 2150)
      3000 (2800 to 3200)
      4000 (3800 to 4200)
      5000 (4800 to 5200)
      6000 (5750 to 6250)
      7000 6700 to 7300
      8000 (7700 to 8300)