THEFT DETERRENT SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. According to the display on the GTS, read the Data List.

      Main Body (Main Body ECU (Multiplex Network Body ECU))
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RR Door Courtesy SW Rear door courtesy light switch RH/ON or OFF

      ON: Rear door RH open

      OFF: Rear door RH closed

      		 -
      RL Door Courtesy SW Rear door courtesy light switch LH/ON or OFF

      ON: Rear door LH open

      OFF: Rear door LH closed

      		 -
      Back Door Courtesy SW Back door courtesy switch/ON or OFF

      ON: Back door open

      OFF: Back door closed

      		 -
      RR-Door Lock Pos SW Rear door RH unlock detection switch/ON or OFF

      ON: Rear door RH unlocked

      OFF: Rear door RH locked

      		 -
      RL-Door Lock Pos SW Rear door LH unlock detection switch/ON or OFF

      ON: Rear door LH unlocked

      OFF: Rear door LH locked

      		 -
      FR Door Lock Pos Front door RH unlock detection switch/LOCK or UNLOCK

      LOCK: Front door RH locked

      UNLOCK: Front door RH unlocked

      		 -
      FL Door Lock Pos Front door LH unlock detection switch/LOCK or UNLOCK

      LOCK: Front door LH locked

      UNLOCK: Front door LH unlocked

      		 -
      FR Door Courtesy Front door courtesy light switch RH/ON or OFF

      ON: Front door RH open

      OFF: Front door RH closed

      		 -
      FL Door Courtesy Front door courtesy light switch LH/ON or OFF

      ON: Front door LH open

      OFF: Front door LH closed

      		 -
      Hood Courtesy SW Security courtesy switch signal/ON or OFF

      ON: Engine hood open

      OFF: Engine hood closed

      		 -
      Intrusion Sens OFF SW Intrusion sensor cancel switch/ON or OFF

      ON: Intrusion sensor cancel switch on

      OFF: Intrusion sensor cancel switch off

      		 -
      Intrusion Sensor Status of the intrusion sensor detection/ON or OFF

      ON: Intrusion sensor detected

      OFF: Intrusion sensor not detected

      		 -
      Tilt Sensor*1 Status of the tilt sensor detection/ON or OFF

      ON: Tilt sensor detected

      OFF: Tilt sensor not detected

      		 -
      Intrusion Sen Conn Intrusion sensor connecting/ON or OFF

      ON: Intrusion sensor connected

      OFF: Intrusion sensor not connected

      		 -
      Tilt Sensor Connect*1 Tilt sensor connecting/ON or OFF

      ON: Tilt sensor connected

      OFF: Tilt sensor not connected

      		 -
      Sealed Glas Brak Sen*1 Glass breakage sensor connecting/with or without

      With: Glass breakage sensor connected

      Without: Glass breakage sensor not connected

      		 -
      Intrusion Sensor Sound Detect*2*3 State of the intrusion sensor sound detection/ON or OFF

      ON: Sound detected

      OFF: Sound not detected

      		 Only displays "ON" on the Data List once. When checking again, disconnect and reconnect the GTS.
      Intrusion Sensor Sensitivity Level*2 State of the intrusion sensor sensitivity level/Normal, Low, Lowest, High, Highest or N+Sound Customized value displayed -

      • *1: w/ Combination Meter Assembly with mph Units

      • *2: w/o Door Ajar Warning Buzzer Function

      Note

      *3: Perform the intrusion sensor operation inspection with the GTS disconnected Click here.

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. The Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body / Main Body / Active Test.

    5. According to the display on the GTS, perform the Active Test.

      Main Body (Main Body ECU (Multiplex Network Body ECU))
      Tester Display Test Part Control Range Diagnostic Note
      Hazard Hazard warning lights ON / OFF -
      Security Indicator Security indicator ON / OFF -
      Vehicle Horn Vehicle horns ON / OFF -
      Security Horn2 Theft warning siren ON / OFF -
      Power for Intrusion sensor Intrusion sensor power supply ON / OFF -
      Power for Tilt sensor* Tilt sensor power supply ON / OFF -

      • *: w/ Combination Meter Assembly with mph Units