PUSH-BUTTON START SYSTEM CUSTOMIZE PARAMETERS

CUSTOMIZE PUSH-BUTTON START SYSTEM

1. Customizing with the intelligent tester

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Enter the following menus: Body / Entry&Start / Utility / Customize / Entry&Start or Warning.

   5. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Auto Entry Cancel SW	OFF	Function that enables or disables the push-button start system.	ON or OFF	Certification ECU (smart key ECU assembly)
      Ignition Available Area (Entry ignition available area)	All	Function that sets the area that the key must be in before the power switch can be operated.	Front or All
      Key Low Battery Warning (Warn when key battery becomes weak)	ON	Enables or disables the sounding of the buzzer when the key battery is low and the power switch is turned off after being on (IG) for 20 minutes or more.	ON or OFF

2. Customizing with the multi-display (w/ Multi-display)

   
   

   1. Turn the power switch on (IG).

   2. Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Door Lock Settings.

   3. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Entry and Start System	On	Function that enables or disables the entry and start system.	On or Off	Certification ECU (smart key ECU assembly)

3. Customizing with the Combination meter assembly

   Tip:
   

   • Press and hold DISP (steering pad switch assembly) when entering an item.

   • Briefly press DISP (steering pad switch assembly) when selecting an item.

   
   

   1. Turn the power switch on (IG).

   2. Enter the following menus: SETTINGS / VEHICLE SETTINGS

   3. Select the setting by referring to the table below

      Display	Default	Content	Setting	Relevant ECU
      ENTRY AND START SYSTEM	ON	Function that enables or disables the push-button start system.	ON or OFF	Certification ECU (smart key ECU assembly)

   4. Press and hold DISP (steering pad switch assembly).

   5. The setting completion screen will be displayed.

   6. Return to the item selection screen.

4. Push-button start cancel function (manual operation)

   Tip:

   While the push-button start system is canceled, the push-button start system can be operated by holding the key against the power switch.

   
   

   1. The following functions are disabled when the push-button start system is canceled.

      
      

      1. Push-button start function

      2. Key lock-in prevention function

      3. Push-button start warning functions

   2. When canceling the system through manual operation:

      
      

      1. Make sure the following conditions are met:

      2. 
         

         • The power switch is off.

         • The driver door is closed.

         • The driver door is unlocked.

      3. Press the unlock button of the key.

      4. Open the driver door within 5 seconds of completing the step above (driver door: closed at beginning of step → opened).

      5. With the driver door open, press the unlock button of the key 2 times within 5 seconds of completing the step above.

         Note:

         If the driver door is closed before or while pressing the unlock button, the push-button start cancel setting mode will end.

      6. Close and open the driver door twice within 30 seconds of completing the step above (driver door: open at beginning of step → closed → opened → closed → opened).

      7. With the driver door open, press the unlock button of the key 2 times within 30 seconds of completing the step above.

         Note:

         If the driver door is closed before or while pressing the unlock button, the push-button start cancel setting mode will end.

      8. Close and open the driver door within 30 seconds of completing the step above (driver door: open at beginning of step → closed → opened)

      9. Close the driver door within 5 seconds of completing the step above.

      10. Check that the wireless buzzer sounds twice (short beeps) to confirm that the push-button start system has been canceled.

   3. Perform the following procedure to restore the push-button start system to the active state from the canceled state.

      
      

      1. Perform the procedures to cancel the push-button start system again.

      2. Check that the wireless buzzer sounds once (short beep) to confirm that the push-button start system has been restored to the active state.

         Tip:
         

         • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

         • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.