ENTRY AND START SYSTEM (for Start Function) CUSTOMIZE PARAMETERS

CUSTOMIZE ENTRY AND START SYSTEM (for Start Function)

1. Customizing with the intelligent tester

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester on.

   4. Body / Entry&Start / Utility / Customize / Entry&Start or Warning

   5. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Auto Entry Cancel SW	OFF	Function that enables or disables the entry and start system.	ON or OFF	Certification ECU (smart key ECU assembly)
      Ignition Available Area (Entry ignition available area)	All	Function that sets the area that the key must be in before the power switch can be operated.	Front or All	Certification ECU (smart key ECU assembly)
      Key Low Battery Warning (Warn when key battery becomes weak)	ON	Enables or disables the sounding of the buzzer when the key battery is low and the power switch is turned off after being on (IG) for 20 minutes or more.	ON or OFF	Certification ECU (smart key ECU assembly)

2. Customizing with the multi-display (w/ Multi-display)

   
   

   1. Turn the power switch on (IG).

   2. Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization / Door Lock Settings.

   3. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Entry and Start System	On	Function that enables or disables the entry and start system.	On or Off	Certification ECU (smart key ECU assembly)

3. Customizing with the Combination meter assembly (w/o Multi-display)

   Tech Tips

   
   

   • Press and hold the DISP (steering pad switch assembly) when entering an item.

   • Briefly press the DISP (steering pad switch assembly) when selecting an item.

   
   

   1. Turn the power switch on (IG).

   2. Enter the following menus: Settings / Vehicle Settings.

   3. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      ENTRY AND START SYSTEM	ON	Function that enables or disables the entry and start system.	ON or OFF	Certification ECU (smart key ECU assembly)

   4. Press and hold the DISP (steering pad switch assembly).

   5. The setting completion screen will be displayed.

   6. Return to the item selection screen.

4. Entry cancel function (manual operation)

   Note

   Because the key (for card type) does not have a wireless transmitter function, it cannot be used to change the entry unlock mode.

   Tech Tips

   While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the key against the power switch.

   
   

   1. The following functions are disabled when the entry and start system is canceled.

      
      

      1. Entry unlock/lock functions

      2. Push-button start function

      3. Key lock-in prevention function

      4. Entry warning functions

   2. When canceling the system through manual operation:

      
      

      1. Make sure the following conditions are met:

      
      

      • The power switch is off.

      • The driver door is closed.

      • The driver door is unlocked.

      2. Press the unlock button of the key.

      3. Open the driver door within 5 seconds of completing the step above (driver door: closed at beginning of step → opened).

      4. With the driver door open, press the unlock button of the key 2 times within 5 seconds of completing the step above.

         Note

         If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      5. Close and open the driver door twice within 30 seconds of completing the above step (driver door: open at beginning of step → closed → opened → closed → opened).

      6. With the driver door open, press the unlock button of the key 2 times within 30 seconds of completing the step above.

         Note

         If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      7. Close and open the driver door within 30 seconds of completing the step above (driver door: open at beginning of step → closed → opened).

      8. Close the driver door within 5 seconds of completing the above step.

      9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the entry and start system has been canceled.

   3. Perform the following procedure to restore the entry and start system to the active state from the canceled state.

      
      

      1. Perform the procedures to cancel the entry and start system again.

      2. Check that the wireless buzzer sounds once (short beep) to confirm that the entry and start system has been restored to the active state.

         Tech Tips

         
         

         • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

         • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.