ENTRY AND START SYSTEM (for Entry Function) SYSTEM DESCRIPTION

VEHICLE AUXILIARY BATTERY SAVING FUNCTION

1. When the entry and start system (for Entry Function) is operating, the vehicle performs key detection operations every 0.25 seconds. Therefore, if the vehicle left as is for a long period of time, the auxiliary battery may become fully discharged. The following controls help reduce the rate at which the auxiliary battery is depleted.

   
   

   1. If the hybrid system is not started for 5 days or more, periodic signal transmission from the electrical key antennas stops. However, the doors can still be unlocked by touching the unlock sensor of a front door outside handle assembly.

   2. If the hybrid system is not started for 14 days or more, the lock and unlock sensors of the front passenger door outside handle assembly are disabled. Therefore, only the unlock sensor of the front door outside handle assembly of the driver door can be used to unlock the doors.

   3. If 10 minutes or more elapse while the key is in the detection area (including the vehicle interior), entry and start system control stops operating.

2. To restore operation of the entry and start system, perform any of the following operations.

   
   

   1. While carrying the key, touch the lock or unlock sensor of the front door outside handle assembly of the driver side door and perform a door lock or unlock operation.

   2. Lock or unlock the doors with the wireless operation.

   3. Insert the mechanical key into the door key cylinder of the driver door and lock or unlock the doors.

WIRELESS BUZZER VOLUME ADJUSTMENT FUNCTION (w/ Wireless Buzzer Answer Back Function)

1. The volume of the wireless buzzer can be changed through the customize function.

   Tech Tips

   The volume of the following wireless buzzer operations cannot be adjusted.

   
   

   • Warning function buzzer operations

   • Customize function buzzer operations

   • Buzzer operations for key diagnostic mode using the intelligent tester

   • Key registration buzzer operations

WARNING FUNCTION

1. Warning

   
   

   1. When any of the situations below occur, the entry and start system causes the certification ECU (smart key ECU assembly) to sound a buzzer in the combination meter assembly and the wireless door lock buzzer*, a message to appear on the multi-information display, and the power switch illumination to operate in order to alert the driver.

      
      

      • *: w/ Door Ajar Warning Function

   2. Situation: The key reminder sounds.

      
      

      • When the driver door is open, the driver turns the power switch on (ACC) and attempts to leave the vehicle.

        Reason for warning	Vehicle theft
        Warning Start Condition (Either condition is met)	The power switch is on (ACC). The driver door is opened.
        Waning description	Buzzer in combination meter assembly sounds continuously
        Warning Stop Condition (One of conditions is met)	The warning is stopped when one of the following conditions is met: The power switch is turned on (IG). The driver door is closed. The power switch is turned off and the shift control is locked.

   3. Situation: The hybrid control system is left running and park (P) has been selected when the driver gets out of the vehicle.

      
      

      • There are 2 patterns for this situation.

      
      

      • Pattern 1:

        When the hybrid control system is left running and park (P) has been selected, the driver closes the driver door and attempts to leave the vehicle while holding the key.

        In this situation, the following control is performed:

        Reason for warning	Vehicle theft, hybrid control system cannot be restarted, discharged auxiliary battery
        Warning Start Condition (All conditions are met)	Park (P) has been selected. The power switch is in a mode other than off. The key is not in the vehicle. The driver door is opened → closed. The vehicle speed is 0 km/h (0 mph).
        Waning description	Buzzer in combination meter assembly sounds once. "Key not Detected" is displayed on multi-information display in combination meter assembly. Wireless buzzer sounds 3 times*.
        Warning Stop Condition (Either condition is met)	The power switch is turned off. The key is returned to the vehicle.

      • *: w/ Door Ajar Warning Function

      
      

      • Pattern 2:

        Under the situation of pattern 1, the driver touches the lock sensor on the door outside handle assembly.

        In this situation, the following control is performed:

        Reason for warning	Vehicle theft, discharged auxiliary battery
        Warning Start Condition (All conditions are met)	The power switch is in a mode other than off. Park (P) has been selected. All doors are closed. The key is in the outside detection areas. The lock sensor is on. The vehicle speed is 0 km/h (0 mph).
        Waning description	Buzzer in combination meter assembly sounds once. "Turn power off" is displayed on multi-information display in combination meter assembly for 60 seconds. "Key not detected" is displayed on multi-information display in combination meter assembly. Wireless buzzer sounds continuously.
        Warning Stop Condition (One of conditions is met)	The power switch is turned off. With park (P) selected, the shift lever is moved to select another shift state. The vehicle speed is above 0 km/h (0 mph). 10 seconds have elapsed after the wireless door lock buzzer is activated (only buzzer stops). Any door is opened (only buzzer stops). Key is returned to the vehicle.

   4. Situation: Door is ajar (w/ Door Ajar Warning Function).

      
      

      • The lock sensor on the door outside handle assembly is touched to perform entry lock with a door open.

        In this situation, the following control is performed:

        Reason for warning	Vehicle theft
        Warning Start Condition (All conditions are met)	The power switch is off. Any door other than the door that performed the entry lock operation is open. The lock sensor on a door outside handle assembly is on (touched). The key is in the outside detection areas.
        Waning description	Wireless buzzer sounds continuously.
        Warning Stop Condition (One of conditions is met)	The power switch is turned to a mode other than off. All doors are closed. An unlock operation is performed using the wireless door lock remote function. The touch sensor on the inner side of a door outside handle assembly is used to perform entry unlock. 10 seconds have elapsed after the wireless door lock buzzer is activated.

   5. Situation: The hybrid control system is left running when a passenger gets out of the vehicle while holding the key.

      
      

      • When the hybrid control system is left running, a passenger leaves the vehicle while holding the key.

        In this situation, the following control is performed:

        Reason for warning	Hybrid control system cannot be restarted
        Warning Start Condition (All conditions are met)	The power switch is in a mode other than off. A door other than the driver door is opened → closed. The vehicle speed is 0 km/h (0 mph). The key is not in the vehicle.
        Waning description	Buzzer in combination meter assembly sounds once. "Key not detected" is displayed on multi-information display in combination meter assembly. Wireless buzzer sounds 3 times.
        Warning Stop Condition (Either condition is met)	The power switch is turned off. The key is returned to the vehicle.

   6. Situation: The key is not in the detection areas.

      
      

      • When the key is not in the vehicle or the key battery is dead, the driver attempts to start the hybrid control system or turn the power switch on (IG).

        In this situation, the following control is performed:

        Reason for warning	Confuses the user
        Warning Start Condition (All conditions are met)	The power switch is pushed. The key is not in the vehicle or the key battery is dead.
        Waning description	Buzzer in combination meter assembly sounds once. "Key not detected" is displayed on multi-information display in combination meter assembly for 15 seconds.
        Warning Stop Condition (One of conditions is met)	The power switch is turned off. The key is in the vehicle or replace the key battery.

   7. Situation: The key is left in the vehicle.

      
      

      • There are two patterns for this situation.

      
      

      • Pattern 1:

        The lock sensor on a door outside handle assembly is touched to perform entry lock with the key left in the vehicle.

        In this situation, the following control is performed:

        Reason for warning	Vehicle theft
        Warning Start Condition (All conditions are met)	The power switch is off. All doors are closed. The key is in the vehicle. The lock sensor on a door outside handle assembly is on (touched). Any door is unlocked.
        Waning description	Buzzer in combination meter assembly sounds once. "Key Detected in Vehicle" is displayed on multi-information display in combination meter assembly for 60 seconds. Wireless buzzer sounds continuously*.
        Warning Stop Condition (One of conditions is met)	The power switch is turned to a mode other than off. Lock operation is detected. 10 seconds have elapsed after the wireless door lock buzzer is activated (only buzzer stops)*. Any door is opened (only buzzer stops)*.

      • *: w/ Door Ajar Warning Function

      
      

      • Pattern 2:

        With a door open and the key in the vehicle, the lock knob is locked and then the door is closed with the door handle being pulled.

        In this situation, the following control is performed:

        Reason for warning	Vehicle theft
        Warning Start Condition (All conditions are met)	With a door open, the lock knob is locked and then the door is closed with the door handle being pulled. The key is in the vehicle.
        Waning description	Buzzer in combination meter assembly sounds once. "Key Detected in Vehicle" is displayed on multi-information display in combination meter assembly for 60 seconds. Wireless buzzer sounds continuously*.
        Warning Stop Condition (One of conditions is met)	The power switch is turned to a mode other than off. The vehicle speed is above 0 km/h (0 mph). Lock operation is detected. 10 seconds have elapsed after the wireless door lock buzzer is activated (only buzzer stops)*. Any door is opened (only buzzer stops)*.

      • *: w/ Door Ajar Warning Function

   8. Situation: The key battery is weak.

      
      

      • The vehicle is driven using a key that has a low battery.

        In this situation, the following control is performed:

        Reason for warning	Entry and start system does not function
        Warning Start Condition (Both conditions are met)	The power switch is turned off after being left on (IG) for more than 20 minutes. The key battery voltage is low.
        Waning description	Buzzer in combination meter assembly sounds once. "Key Battery Low" is displayed on multi-information display in combination meter assembly for 15 seconds.
        Warning Stop Condition	The key battery is replaced with a new one.

   9. Situation: The power management ECU is malfunctioning.

      
      

      • A malfunction of the power management control ECU is detected.

        In this situation, the following control is performed:

        Reason for warning	Malfunction detection
        Warning Start Condition	A malfunction of the power management ECU is detected.
        Waning description	Power switch indicator blinks amber at 2 second intervals for 15 seconds.
        Warning Stop Condition	The power management control ECU returns to normal.

   10. Situation: The hybrid control system does not start. (Situation A)

       
       

       • There are two patterns for this situation.

       
       

       • Pattern 1:

         A warning message appears on the multi-information display when the driver does not follow the proper procedure to start the vehicle.

         In this situation, the following control is performed:

         Reason for warning	Usability function
         Warning Start Condition (All conditions are met)	The power switch is turned off. Driver door is closed → opened. The power switch is turned from off to on (ACC) more than twice with the hybrid control system off and the brake pedal not depressed.
         Waning description	Buzzer in combination meter assembly sounds once. "Depress Brake Pedal and Push Power Switch to Start" is displayed on multi-information display in combination meter assembly for 10 seconds.
         Warning Stop Condition (One of conditions is met)	The power switch is turned off. The power switch is turned on (IG).

       • Pattern 2:

         A message indicating how to start the hybrid control system appears on the multi-information display when the shift lever is in a position in which the hybrid control system cannot be started.

         In this situation, the following control is performed:

         Reason for warning	Usability function
         Warning Start Condition (All conditions are met)	The hybrid control system is stopped. The vehicle speed is 0 km/h (0 mph). More than 0.5 seconds have elapsed after the power switch is turned on (IG). The shift state other than park (P).
         Waning description	Buzzer in combination meter assembly sounds once. "Shift to P Position to Start" is displayed on multi-information display in combination meter assembly.
         Warning Stop Condition (One of conditions is met)	The P position switch (transmission shift main switch) is pushed. The vehicle speed is above 0 km/h (0 mph). The power switch is turned off or on (ACC). The hybrid control system is started.

   11. Situation: The hybrid control system does not start. (Situation B)

       
       

       • There are two patterns for this situation.

       
       

       • Pattern 1:

         When the power switch is pushed, the key cannot be detected in the vehicle two times in a row.

         In this situation, the following control is performed:

         Reason for warning	Usability function
         Warning Start Condition (All conditions are met)	The immobiliser system is set. The key is not in the vehicle. Key code verification error occurs when the power switch is pushed twice.
         Waning description	Buzzer in combination meter assembly sounds once. "Depress Brake Pedal, Touch Power Switch with Key" is displayed on multi-information display in combination meter assembly for 60*1 or 30*2 seconds.
         Warning Stop Condition (Either condition is met)	The immobiliser system certification result is OK. The key is in the vehicle.

         *1: When the brake pedal is depressed.

         *2: When the brake pedal is not depressed.

       • Pattern 2:

         The driver attempts to start the hybrid control system after performing a driver door key linked unlock operation.

         In this situation, the following control is performed:

         Reason for warning	Usability function
         Warning Start Condition (All conditions are met)	A driver door key linked unlock operation is performed. The immobiliser system is set. The power switch is pushed. The key is not in detected the vehicle.
         Waning description	Buzzer in combination meter assembly sounds once. "Depress Brake Pedal, Touch Power Switch with Key" is displayed on multi-information display in combination meter assembly for 60 seconds.
         Warning Stop Condition (Either condition is met)	The immobiliser system certification result is OK. The key is detected to the vehicle.

   12. Situation: Immobiliser system certification completion occurs.

       
       

       • A warning message appears on the multi-information display when a key with a depleted battery is touched to the power switch while depressing the brake.

         In this situation, the following control is performed:

         Reason for warning	Malfunction detection
         Warning Start Condition	Key certification result is OK.
         Waning description	Buzzer in combination meter assembly sounds once. "Depress Brake Pedal and Push Power Switch to Start" is displayed on multi-information display in combination meter assembly for 10 seconds. Power switch indicator blinks amber.
         Warning Stop Condition (Either condition is met)	The hybrid control system is started. The key is detected to the vehicle. The immobiliser system is set and room recognize is stopped or cannot be recognized.

   13. Situation: Auto power off operation occurs.

       
       

       • A warning message appears on the multi-information display when automatic power off operation occurs.

         In this situation, the following control is performed:

         Reason for warning	Auxiliary battery saving function
         Warning Start Condition (All conditions are met)	Park (P) has been selected. The power switch is on (ACC) or on (IG). The vehicle speed is 0 km/h (0 mph). The hybrid control system is stopped. The power source control system is turned off by automatic power off function.
         Waning description	"Auto Power Off to Conserve Battery" is displayed on multi-information display in combination meter assembly for 10 seconds.
         Warning Stop Condition	The power switch is turned to a mode other than off.

   14. Situation: The vehicle is driven without a key.

       
       

       • A warning message appears on the multi-information display when the vehicle starts moving without the registered key in the vehicle.

         In this situation, the following control is performed:

         Reason for warning	Hybrid control system cannot be restarted
         Warning Start Condition	When vehicle speed is detected after the key is removed from the vehicle, the warning is activated (only for first time).
         Waning description	Buzzer in combination meter assembly sounds once. "Key not Detected" is displayed on multi-information display in combination meter assembly.
         Warning Stop Condition (Either condition is met)	The power switch is turned off. The key is returned to the vehicle.