REAR DOOR LOCK INSPECTION

INSPECT REAR DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

1. 

   Text in Illustration

   *a	Component without harness connected (Rear Door Lock Assembly LH)
   *b	Unlock
   *c	Lock

   Check the operation of the door lock motor.

   
   

   1. Apply auxiliary battery voltage and check the operation of the door lock motor.

      OK
      Connection Result Auxiliary battery positive (+) → Terminal 4 (L) Auxiliary battery negative (-) → Terminal 1 (UL) Locks Auxiliary battery positive (+) → Terminal 1 (UL) Auxiliary battery negative (-) → Terminal 4 (L) Unlocks

      If the result is not as specified, replace the rear door lock assembly LH.

2. 

   Text in Illustration

   *a	Component without harness connected (Rear Door Lock Assembly LH)
   *b	Unlock
   *c	Lock

   Check the operation of the unlock detection switch.

   
   

   1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 6 (LSSR) - 9 (E) Locked 10 kΩ or higher 6 (LSSR) - 9 (E) Unlocked Below 1 Ω

      If the result is not as specified, replace the rear door lock assembly LH.

INSPECT REAR DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

1. 

   Text in Illustration

   *a	Component without harness connected (Rear Door Lock Assembly LH)
   *b	Unlock
   *c	Lock

   Check the operation of the door lock motor and double lock motor.

   
   

   1. Apply auxiliary battery voltage and check the operation of the door lock motor and double lock motor.

      OK
      Connection Result Auxiliary battery positive (+) → 2 (L) Auxiliary battery negative (-) → 1 (UL) Locks Auxiliary battery positive (+) → 1 (UL) Auxiliary battery negative (-) → 2 (L) Unlocks Auxiliary battery positive (+) → 4 (DL) Auxiliary battery negative (-) → 3 (UNDL) Sets Auxiliary battery positive (+) → 3 (UNDL) Auxiliary battery negative (-) → 4 (DL) Unsets

      Tech Tips

      
      

      • Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

      • Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

      If the result is not as specified, replace the rear door lock assembly LH.

2. 

   Text in Illustration

   *a	Component without harness connected (Rear Door Lock Assembly LH)
   *b	Unlock
   *c	Lock

   Check the operation of the unlock detection switch and double lock position switch.

   
   

   1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 5 (LSSR) - 6 (E) Locked 10 kΩ or higher 5 (LSSR) - 6 (E) Unlocked Below 1 Ω 9 (DLSR) - 10 (E) Unset 10 kΩ or higher 9 (DLSR) - 10 (E) Set Below 1 Ω

      If the result is not as specified, replace the rear door lock assembly LH.

INSPECT REAR DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

1. 

   Text in Illustration

   *a	Component without harness connected (Rear Door Lock Assembly RH)
   *b	Unlock
   *c	Lock

   Check the operation of the door lock motor.

   
   

   1. Apply auxiliary battery voltage and check the operation of the door lock motor.

      OK
      Connection Result Auxiliary battery positive (+) → Terminal 4 (L) Auxiliary battery negative (-) → Terminal 1 (UL) Locks Auxiliary battery positive (+) → Terminal 1 (UL) Auxiliary battery negative (-) → Terminal 4 (L) Unlocks

      If the result is not as specified, replace the rear door lock assembly RH.

2. 

   Text in Illustration

   *a	Component without harness connected (Rear Door Lock Assembly RH)
   *b	Unlock
   *c	Lock

   Check the operation of the unlock detection switch.

   
   

   1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 6 (LSSR) - 9 (E) Locked 10 kΩ or higher 6 (LSSR) - 9 (E) Unlocked Below 1 Ω

      If the result is not as specified, replace the rear door lock assembly RH.

INSPECT REAR DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

1. 

   Text in Illustration

   *a	Component without harness connected (Rear Door Lock Assembly RH)
   *b	Unlock
   *c	Lock

   Check the operation of the door lock motor and double lock motor.

   
   

   1. Apply auxiliary battery voltage and check the operation of the door lock motor and double lock motor.

      OK
      Connection Result Auxiliary battery positive (+) → 4 (L) Auxiliary battery negative (-) → 3 (UL) Locks Auxiliary battery positive (+) → 3 (UL) Auxiliary battery negative (-) → 4 (L) Unlocks Auxiliary battery positive (+) → 2 (DL) Auxiliary battery negative (-) → 1 (UNDL) Sets Auxiliary battery positive (+) → 1 (UNDL) Auxiliary battery negative (-) → 2 (DL) Unsets

      Tech Tips

      
      

      • Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

      • Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.

      If the result is not as specified, replace the rear door lock assembly RH.

2. Check the operation of the unlock detection switch and double lock position switch.

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Rear Door Lock Assembly RH)
      *b	Unlock
      *c	Lock

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 9 (LSSR) - 10 (E) Locked 10 kΩ or higher 9 (LSSR) - 10 (E) Unlocked Below 1 Ω 5 (DLSR) - 6 (E) Unset 10 kΩ or higher 5 (DLSR) - 6 (E) Set Below 1 Ω

      If the result is not as specified, replace the rear door lock assembly RH.