REAR DOOR LOCK REMOVAL


  1. PRECAUTION

    Note

    After the power switch is turned off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. REMOVE REAR NO. 2 FLOOR BOARD


    1. Remove the rear No. 2 floor board.

  3. REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  4. REMOVE REAR NO. 3 FLOOR BOARD


    1. Remove the rear No. 3 floor board.

  5. REMOVE DECK FLOOR BOX RH


    1. A003Z5J

      Remove the clip.

    2. Disengage the 6 guides and remove the deck floor box RH.

  6. REMOVE REAR FLOOR BOARD UPPER NO. 3 PLATE


    1. A003VKN

      Disengage the 4 claws and 2 guides, and remove the rear floor board upper No. 3 plate.

  7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A003YVN

      Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.

  9. REMOVE REAR DOOR REAR FRAME BRACKET


    1. A003WT2

      Disengage the clip, 3 claws and 3 guides and remove the rear door rear frame bracket.

  10. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A003X74

      Using a moulding remover, disengage the 3 clips, 4 claws and 2 guides as shown in the illustration.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  11. REMOVE REAR DOOR ARMREST COVER


    1. A003WKN

      Remove the rear door armrest cover.

  12. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A003WA9E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the rear door panel.

    2. A003VT0

      Remove the 2 screws.

    3. Using a clip remover, disengage the 9 clips.

    4. A003XWL

      Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    5. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

    6. Disconnect the connector.

    7. A003ZHN

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    8. Remove the rear door trim board clip (blue) from the rear door trim board.

  13. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    1. A003ZV5E01
      Text in Illustration
      *1 Screwdriver

      Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.

  14. REMOVE REAR DOOR TRIM BRACKET


    1. A003VYL

      Remove the 2 screws and rear door trim bracket.

  15. REMOVE REAR DOOR SERVICE HOLE COVER


    1. A003YUO

      Disengage the clamp.

    2. Disconnect the connector and remove the rear door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  16. REMOVE REAR DOOR CHECK ASSEMBLY


    1. A003WBD

      Remove the 3 bolts and rear door check assembly.

  17. REMOVE REAR DOOR WEATHERSTRIP


    1. A003YQNE01
      Text in Illustration
      *1 Double-sided Tape

      Using a clip remover, disengage the 23 clips and remove the rear door weatherstrip.

  18. REMOVE REAR DOOR GLASS RUN


    1. A003VUE

      Remove the rear door glass run.

  19. REMOVE NO. 1 REAR DOOR VENT SEAL


    1. A003ZME

      Remove the No. 1 rear door vent seal.

  20. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. A003ZUUE01
      Text in Illustration
      *1 Temporary Bolt

      Loosen the temporary bolt.

    2. Remove the bolt and screw and rear door window division bar sub-assembly.

      Note

      When the rear door window division bar sub-assembly is removed, do not allow the rear door quarter window glass to fall.

    3. Remove the temporary bolt from the rear door window division bar sub-assembly.

  21. REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. A003XAR

      Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.

    2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

  22. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. A003XXI

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  23. REMOVE REAR DOOR LOCK ASSEMBLY (w/o Double Locking System)


    1. A003XN0

      Using a T30 "TORX" socket wrench, remove the 3 screws.

    2. Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.

    3. A003V8C

      Remove the door lock wiring harness seal from the rear door lock assembly.

    4. A003ZP1

      Using a screwdriver, disengage the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    5. A003XT0

      Remove the rear door lock remote control cable assembly.

    6. A003VFV

      Using a screwdriver, disengage the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    7. A003Y8W

      Remove the rear door inside locking cable assembly.

  24. REMOVE REAR DOOR LOCK ASSEMBLY (w/ Double Locking System)


    1. A003XN0

      Using a T30 "TORX" socket wrench, remove the 3 screws.

    2. Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.

    3. A003V8C

      Remove the door lock wiring harness seal from the rear door lock assembly.

    4. A003WQH

      Using a screwdriver, disengage the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    5. A003ZCT

      Remove the rear door lock remote control cable assembly.

    6. A003WD0

      Using a screwdriver, disengage the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    7. A003ZB2

      Remove the rear door inside locking cable assembly.