POWER MANAGEMENT CONTROL ECU REMOVAL


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. REMOVE REAR NO. 2 FLOOR BOARD


    1. Remove the rear No. 2 floor board.

  3. REMOVE REAR DECK FLOOR BOX


    1. Remove the rear deck floor box.

  4. REMOVE REAR NO. 3 FLOOR BOARD


    1. Remove the rear No. 3 floor board.

  5. REMOVE DECK FLOOR BOX RH


    1. A003Z5J

      Remove the clip.

    2. Disengage the 6 guides and remove the deck floor box RH.

  6. REMOVE REAR FLOOR BOARD UPPER NO. 3 PLATE


    1. A003VKN

      Disengage the 4 claws and 2 guides, and remove the rear floor board upper No. 3 plate.

  7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for LHD)

    Tech Tips

    Use the same procedure as for the LH side Click here.

  9. REMOVE FRONT DOOR SCUFF PLATE RH (for LHD)

    Tech Tips

    Use the same procedure as for the LH side Click here.

  10. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH (for LHD)

    Tech Tips

    Use the same procedure as for the LH side Click here.

  11. REMOVE INSTRUMENT SIDE PANEL RH (for LHD)


    1. A003ZIT

      Using a moulding remover, disengage the 3 claws, clip and 4 guides, and remove the instrument side panel RH.

    2. Disconnect the connector.

  12. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. A003ZFG

      Disengage the 2 clips, claw and guide.

    2. Disengage the clamp.

    3. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.

  13. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)

    CAUTION:

    When storing the lower No. 2 instrument panel airbag assembly, keep the airbag deployment side facing upward.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A003ZSE

      Remove the 3 bolts.

    4. A003Y7X

      Disengage the 6 claws and 2 guides to separate the lower No. 2 instrument panel airbag assembly.

    5. A003Y1EE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.

    6. Disconnect the airbag connector to remove the lower No. 2 instrument panel airbag assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  14. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (for LHD)


    1. A003ZS4

      Remove the 4 screws <C>.

    2. Disengage the 5 claws.

    3. Disengage the clamp.

    4. Disconnect the connector and remove the glove compartment door assembly.

  15. REMOVE ECU INTEGRATION BOX RH (for LHD)


    1. A003XH1

      Disconnect each connector.

    2. Disengage the clamp and disconnect the wire harness.

    3. Remove the bolt, 2 nuts and ECU integration box RH.

  16. REMOVE POWER MANAGEMENT CONTROL ECU (for LHD)


    1. A003VZJ

      Disengage the 2 claws and remove the power management control ECU as shown in the illustration.

  17. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for RHD)


    1. A003YSW

      Disconnect the front door opening trim weatherstrip.

    2. Remove the residual weatherstrip sealant from the body of the vehicle using cleaner.

      Note

      Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.

  18. REMOVE FRONT DOOR SCUFF PLATE LH (for RHD)


    1. A003VX8

      Disengage the 4 claws, 2 guides and 4 clips, and remove the front door scuff plate LH.

  19. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for RHD)


    1. A003X2U

      Remove the clip as shown in the illustration.

    2. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.

  20. REMOVE INSTRUMENT SIDE PANEL LH (for RHD)


    1. A003Z0S

      Using a moulding remover, disengage the 3 claws, clip and 4 guides, and remove the instrument side panel LH.

  21. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. A003VC3

      Disengage the 2 clips, claw and 2 guides.

    2. Disengage the clamp.

    3. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.

  22. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (for RHD)

    CAUTION:

    When storing the lower No. 2 instrument panel airbag assembly, keep the airbag deployment side facing upward.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A003ZSE

      Remove the 3 bolts.

    4. A003Y7X

      Disengage the 6 claws and 2 guides to separate the lower No. 2 instrument panel airbag assembly.

    5. A003Y1EE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.

    6. Disconnect the airbag connector to remove the lower No. 2 instrument panel airbag assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  23. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (for RHD)


    1. A003ZS4

      Remove the 4 screws <C>.

    2. Disengage the 5 claws.

    3. Disengage the clamp.

    4. Disconnect the connector and remove the glove compartment door assembly.

  24. REMOVE ECU INTEGRATION BOX LH (for RHD)


    1. A003YA0

      Disconnect each connector.

    2. Disengage the clamp and disconnect the wire harness.

    3. Remove the bolt, nut and ECU integration box LH.

  25. REMOVE POWER MANAGEMENT CONTROL ECU (for RHD)


    1. A003Y80

      Disengage the 2 claws and remove the power management control ECU as shown in the illustration.