G-BOOK SYSTEM Telematics Transceiver Malfunction

WIRING DIAGRAM

A003X7EE10

INSPECTION PROCEDURE

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precautions for G-BOOK Click here.

PROCEDURE


  1. CHECK COMMUNICATION SERVICE CONDITION


    1. Move the vehicle.


      1. If the vehicle is outside the communication service area, move the vehicle to a communication service area, wait for a while and perform the operation again.


    NEXT

  2. CHECK DTC


    1. Clear the DTCs Click here.

    2. Recheck for DTCs and check that no DTCs are output.

      Result
      Result Proceed to
      DTCs are output A
      No DTCs are output B

    B

    DCM CHECK Click here

    A

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

  3. DCM CHECK


    1. DCM Check


      1. Enter diagnostic mode Click here.

      2. Select "Failure Diagnosis" on the "Service Menu" screen.

        A003WOL

      3. Select "DCM Check" on the "Failure Diagnosis" screen.

        A003ZLY

      4. Touch "DCM Check" to perform the DCM Check.

        A003XGT
        Result
        Result Proceed to

        • DCM Check cannot be performed

        • The result of DCM check does not change from "wait"

        • "OK" is displayed for the result of DCM Check

        • "TIME OUT" is displayed for the result of DCM Check

        		 A
        "No Service" is displayed for the result of DCM Check B
        "OFF LINE" is displayed for the result of DCM Check C
        "NO CARRIER" is displayed for the result of DCM Check D
        "ERROR" is displayed for the result of DCM Check E
        "RESTRICTION" is displayed for the result of DCM Check *a

        Tech Tips


        • If the vehicle is moved while the screen is displayed, select "Back" again to renew the result.

        • *a: Retry after waiting for 10 to 30 minutes.


    B

    MOVE VEHICLE

    C

    CHECK CONTRACT FLAG Click here

    D

    CONTACT G-BOOK SUPPORT CENTER

    E

    CHECK PROBLEM SYMPTOM (IG OFF to ACC) Click here

    A

  4. CONTACT G-BOOK SUPPORT CENTER


    1. Check the contract flag.


      1. Enter diagnostic mode Click here.

      2. Select "Service Information" on the "Service Menu" screen.

        A003WOL

      3. Select "G-BOOK Info for Contract" on the "Service Information" screen.

        A003YXZ

      4. Check the flag information item.

        A003X9M

    2. Check the device information.


      1. Select "DCM Information" on the "Service Information" screen.

        A003YXZ

      2. Check the following items on the "DCM Information" screen.

        A003X4V
        Item Content
        Tel No Check if the telematics transceiver phone number is displayed. If the number is displayed, record it.
        DCM Serial Record the telematics transceiver serial number.

    3. Contact the G-BOOK support center.


      1. Contact the G-BOOK support center and inform them about the following:


        • Phenomenon: Communication has been initialized but communication is not possible.

        • Flag information

        • Telephone number (Tel No): Not displayed / Displayed number

        • Serial number (DCM Serial): Displayed number

        • VIN

        Tech Tips

        The G-BOOK support center will perform an investigation and provide the results.

      2. Check for problem symptoms after receiving a call from the G-BOOK support center.

        Result
        Result Proceed to
        Problem symptom recurs A
        System returns to normal B

    B

    END

    A

  5. INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY (USBV, USBG)


    1. Disconnect the H132 multi-media module receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H132-2 (USBG) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H132-4 (USBV) - H132-2 (USBG) Power switch on (ACC) 4.75 to 5.25 V

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)


    1. Check the installation condition.


      1. Check the USB communication cable (digital communication cable) between the multi-media module receiver assembly and the telematics transceiver for any installation or connection problems.

    2. Disconnect the H132 multi-media module receiver assembly connector.

    3. Disconnect the H133 telematics transceiver connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H132-4 (USBV) - H133-4 (USBV) Always Below 1 Ω
      H132-2 (USBG) - H133-2 (USBG) Always Below 1 Ω
      H133-4 (USBV) - Body ground Always 10 kΩ or higher
      H133-2 (USBG) - Body ground Always 10 kΩ or higher
      Standard Resistance (USB Cable)
      Tester Connection Condition Specified Condition
      H132-1-2 (USB+) - H133-1-2 (USB+) Always Below 1 Ω
      H132-1-1 (USB-) - H133-1-1 (USB-) Always Below 1 Ω
      H132-1-3 (USBS) - H133-1-3 (USBS) Always Below 1 Ω
      H133-1-2 (USB+) - Body ground Always 10 kΩ or higher
      H133-1-1 (USB-) - Body ground Always 10 kΩ or higher
      H133-1-3 (USBS) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK RECEPTION LEVEL


    1. A003Y54E01

      Check the reception level.


      1. Check the reception level of the telematics transceiver.

        Tech Tips


        • Check if the reception level is significantly lower by comparing it to a China Telecom cellular phone.

        • If there is no China Telecom cellular phone available, move the vehicle to a location where the reception level indicator shows 3 bars or more.

        • If a problem occurred because the G-BOOK contract has not been completed, proceed to the contract procedure and check the telematics transceiver reception level on the screen during the contract procedure.

        Result
        Result Proceed to

        • The reception level is not lower than a China Telecom cellular phone.

        • 3 or more bars are displayed for the reception level.

        		 A

        • The reception level is lower than a China Telecom cellular phone.

        • Cannot reach 3 or more bars for the reception level even after moving the vehicle.

        		 B

    B

    Click here

    A

  8. REPLACE TELEMATICS TRANSCEIVER


    1. Replace the telematics transceiver with a known good one and check if the same problem occurs again Click here

      OK
      The system returns to normal.

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    OK

    END (TELEMATICS TRANSCEIVER WAS DEFECTIVE)

  9. INSPECT ROOF ANTENNA ASSEMBLY


    1. Check the installation condition.


      1. Check the roof antenna assembly for any installation problems.

        OK
        The roof antenna assembly is installed correctly.

    2. Disconnect the roof antenna assembly connector.

    3. A003VSEE02
      Text in Illustration
      *a

      Component without harness connected

      (Roof Antenna Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 - 2a Always 4 to 11 kΩ

    NG

    REPLACE ROOF ANTENNA ASSEMBLY Click here

    OK

  10. INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY


    1. A003WPJE04
      Text in Illustration
      *a

      Front view of No. 3 antenna cord sub-assembly connector

      (to Roof Antenna Assembly)
      *b

      Front view of No. 3 antenna cord sub-assembly connector

      (to No. 2 Antenna Cord Sub-assembly)

      Disconnect the No. 3 antenna cord sub-assembly connector from the roof antenna assembly.

    2. Disconnect the No. 3 antenna cord sub-assembly connector from the vehicle side wire harness.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 - 3 Always Below 1 Ω
      2a - 3a Always Below 1 Ω
      2 - Body ground Always 10 kΩ or higher
      2a - Body ground Always 10 kΩ or higher

    NG

    REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  11. INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. A003X3OE04
      Text in Illustration
      *a

      Front view of No. 2 antenna cord sub-assembly connector

      (to No. 3 Antenna Cord Sub-assembly)
      *b

      Front view of No. 2 antenna cord sub-assembly connector

      (to Vehicle Side Wire Harness)

      Disconnect the No. 2 antenna cord sub-assembly connector from the No. 3 antenna cord sub-assembly.

    2. Disconnect the No. 2 antenna cord sub-assembly connector from the vehicle side wire harness.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 3 Always Below 1 Ω
      3a - 3a Always Below 1 Ω
      3 - Body ground Always 10 kΩ or higher
      3a - Body ground Always 10 kΩ or higher

    NG

    REPLACE NO.2 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  12. CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - TELEMATICS TRANSCEIVER)


    1. A003VO0E01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 2 Antenna Cord Sub-assembly)
      *b

      Front view of wire harness connector

      (to Telematics Transceiver)

      Disconnect the vehicle side wire harness connector from the No. 2 antenna cord sub-assembly.

    2. Disconnect the vehicle side wire harness connector from the telematics transceiver.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 1 Always Below 1 Ω
      3a - 1a Always Below 1 Ω
      3 - Body ground Always 10 kΩ or higher
      3a - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  13. REPLACE TELEMATICS TRANSCEIVER


    1. Replace the telematics transceiver with a known good one and check if the same problem occurs again Click here.

      OK
      Same problem does not occur.

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    OK

    END (TELEMATICS TRANSCEIVER WAS DEFECTIVE)

  14. CHECK CONTRACT FLAG


    1. Check the contract flag.


      1. Enter diagnostic mode Click here.

      2. Select "Service Information" on the "Service Menu" screen.

        A003WOL

      3. Select "G-BOOK Info for Contract" on the "Service Information" screen.

        A003YXZ

      4. Check if the flag information shown in the illustration indicates "1".

        A003XMA

      5. Turn the power switch off and then to on (ACC).

      6. Check again if the flag information shown in the illustration indicates "1".

    2. Recheck the problem symptom.


      1. Select G-BOOK.com and perform the contract procedure again Click here.

      2. Check for the problem symptom.

        Result
        Result Proceed to
        Contract flag indicates "1" and the system returns to normal. A
        Contract flag indicates "1" but the problem symptom recurs. B
        Contract flag does not indicate "1" and the problem symptom recurs. C

    B

    REPLACE TELEMATICS TRANSCEIVER Click here

    C

    CONTACT G-BOOK SUPPORT CENTER

    A

    END

  15. CHECK PROBLEM SYMPTOM (IG OFF to ACC)


    1. Check for the problem symptom.


      1. Turn the power switch off and then to on (ACC).

      2. Check if the problem symptom recurs.

        Result
        Result Proceed to
        System returns to normal. A
        System does not return to normal. B

    B

    REPLACE TELEMATICS TRANSCEIVER Click here

    A

    END