NAVIGATION SYSTEM (for HDD) Microphone Circuit between Microphone and Navigation ECU

DESCRIPTION

• The navigation computer sub-assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

• Using this circuit, the navigation computer sub-assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the navigation computer sub-assembly (w/o G-BOOK System).

• Using this circuit, the telematics transceiver sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the navigation computer sub-assembly via the telematics transceiver (w/ G-BOOK System).

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. CONFIRM MODEL

   
   

   1. Choose the model to be inspected.

      Result
      Model Proceed to w/o G-BOOK System A w/ G-BOOK System B

   
   

   B

   CHECK HARNESS AND CONNECTOR Click here

   A

2. CHECK HARNESS AND CONNECTOR

   
   

   1. Disconnect the H60 navigation computer sub-assembly connector.

   2. Disconnect the T6 map light assembly connector.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition H60-20 (SNS2) - T6-11 (SNS2) Always Below 1 Ω H60-4 (MACC) - T6-14 (MACC) Always Below 1 Ω H60-5 (MIN+) - T6-13 (MCO+) Always Below 1 Ω H60-6 (MIN-) - T6-12 (MCO-) Always Below 1 Ω H60-20 (SNS2) - Body ground Always 10 kΩ or higher H60-4 (MACC) - Body ground Always 10 kΩ or higher H60-5 (MIN+) - Body ground Always 10 kΩ or higher H60-6 (MIN-) - Body ground Always 10 kΩ or higher H60-7 (SGND) - Body ground Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

3. INSPECT NAVIGATION COMPUTER SUB-ASSEMBLY

   
   

   1. Reconnect the H60 navigation computer sub-assembly connector.

   2. Reconnect the T6 map light assembly connector.

   3. 

      Text in Illustration

      *a	Component with harness connected (Navigation Computer Sub-assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition H60-4 (MACC) - Body ground Power switch on (ACC) 4 to 6 V

   4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition H60-7 (SGND) - Body ground Always Below 1 Ω H60-6 (MIN-) - Body ground Always Below 1 Ω

   5. Proceed to the next step based on the inspection result.

      Result
      Result Proceed to NG A OK B

   
   

   B

   INSPECT MAP LIGHT ASSEMBLY Click here

   A

   REPLACE NAVIGATION COMPUTER SUB-ASSEMBLY Click here

4. CHECK HARNESS AND CONNECTOR

   
   

   1. Disconnect the H60 navigation computer sub-assembly connector.

   2. Disconnect the T6 map light assembly connector.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition H60-20 (SNS2) - T6-11 (SNS2) Always Below 1 Ω

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

5. CHECK HARNESS AND CONNECTOR

   
   

   1. Disconnect the H60 navigation computer sub-assembly connector.

   2. Disconnect the H145 telematics transceiver connector.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition H60-5 (MIN+) - H145-18 (MCO+) Always Below 1 Ω H60-6 (MIN-) - H145-19 (MCO-) Always Below 1 Ω H60-5 (MIN+) - Body ground Always 10 kΩ or higher H60-6 (MIN-) - Body ground Always 10 kΩ or higher H60-7 (SGND) - Body ground Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

6. CHECK HARNESS AND CONNECTOR

   
   

   1. Disconnect the H145 telematics transceiver connector.

   2. Disconnect the T6 map light assembly connector.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition H145-33 (MCVD) - T6-14 (MACC) Always Below 1 Ω H145-34 (MCI+) - T6-13 (MCO+) Always Below 1 Ω H145-35 (MCI-) - T6-12 (MCO-) Always Below 1 Ω H145-33 (MCVD) - Body ground Always 10 kΩ or higher H145-34 (MCI+) - Body ground Always 10 kΩ or higher H145-35 (MCI-) - Body ground Always 10 kΩ or higher H145-32 (SGND) - Body ground Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

7. INSPECT NAVIGATION COMPUTER SUB-ASSEMBLY

   
   

   1. Disconnect the H145 telematics transceiver connector.

   2. 

      Text in Illustration

      *a	Component with harness connected (Navigation Computer Sub-assembly)

      Reconnect the H60 navigation computer sub-assembly connector.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition H60-7 (SGND) - Body ground Always Below 1 Ω H60-6 (MIN-) - Body ground Always Below 1 Ω

   
   

   NG

   REPLACE NAVIGATION COMPUTER SUB-ASSEMBLY Click here

   OK

8. INSPECT TELEMATICS TRANSCEIVER

   
   

   1. Reconnect the H145 telematics transceiver connector.

   2. 

      Text in Illustration

      *a	Component with harness connected (Telematics Transceiver)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition H145-33 (MCVD) - Body ground Power switch on (ACC) 4 to 6 V

   
   

   NG

   REPLACE TELEMATICS TRANSCEIVER Click here

   OK

9. INSPECT MAP LIGHT ASSEMBLY

   
   

   1. Disconnect the T6 map light assembly connector.

   2. 

      Text in Illustration

      *a	Component without harness connected (Map Light Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition T6-11 (SNS2) - T6-12 (MCO-) Always Below 1 Ω

   
   

   NG

   REPLACE TELEPHONE MICROPHONE ASSEMBLY Click here

   OK

10. INSPECT MAP LIGHT ASSEMBLY

    
    

    1. Reconnect the H60 navigation computer sub-assembly connector.

    2. Reconnect the H145 telematics transceiver connector (w/ G-BOOK System).

    3. 

       Text in Illustration

       *a	Component with harness connected (Map Light Assembly)

       Reconnect the T6 map light assembly connector.

    4. Turn the power switch on (ACC).

    5. Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the T6 map light assembly connector.

    6. Check the waveform of the telephone microphone assembly using the oscilloscope.

       Result
       Result Proceed to A waveform synchronized with the voice input to the map light assembly is output A A waveform synchronized with the voice input to the map light assembly is not output B

    
    

    B

    REPLACE TELEPHONE MICROPHONE ASSEMBLY Click here

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

11. REPLACE TELEPHONE MICROPHONE ASSEMBLY

    
    

    1. Replace the telephone microphone assembly Click here.

    2. Check if the same malfunction recurs.

       Result
       Result Proceed to Malfunction does not recur (returns to normal) A Malfunction recurs B

    
    

    B

    REPLACE MAP LIGHT ASSEMBLY Click here

    A

    END